The Trend T421/35 hinge cutter is typically used by kitchen unit manufacturers and fitters for cutting 35mm blind holes ready to accept recessed circular hinges, it has a TCT blade for longer life.This bit is best suited for use on thinner section laminate covered board.Diameter - 35mmShank - 1/4in
The Trend PH/JIG Pocket Hole Jig is great for fast and accurate joining of timber and plywood, giving strong instant joints. Solid hardened bushes with variable pitch of 29mm to 63mm. Use on timber, MDF, plywood and block board. Allows a variety of joints to be created individually. Uses square drive self tapping screws. Work piece can be handled immediately after gluing and screwing, creating time saving benefits. No clamps required.This replacement stepped drill bit for the Pocket Hole Jig has a diameter of 9.5mm (3/8in).
The Trend CB counterbore is extensively used for recessing bolt and screw heads. Supplied with a HSS slow spiral drill bit. Fully adjustable, a hex key is supplied. TCT version is used for plywood, particle boards and plastics (abrasive). Use at drilling speeds only. Not suitable for ferrous and non-ferrous metals. When setting-up, ensure flutes of drill are aligned with flute of counterbore. For replacement Twist Drills, use slow spiral type e.g 501/532 to 501/012.
Trend Bearing Guided Template Profile Cutter for rebating and trimming edges. Extra care must be taken to avoid breakage of the cutter. Two flute carbide TCT tips for clean, professional finish on timber lippings, plastic laminates and veneers. Specially designed PTFE coated bodies to minimise heat and resin build-up and Micro-granular Tungsten Carbide tips ensure a premium finish in hard and soft woods, and abrasive man-made boards such as ply, MDF and chipboard, to meet the needs of the woodworker and tradesman for quality and performance. All Trend router cutters also have a safety ‘K’ mark insertion indicator on each shank to ensure a quick and easy set up whether for hand held or table work.This Trend Bearing Guided Template Profile Cutter has the following specification: (D) Diameter: 12.7mm(C) Cutting Length: 9.5mmShank: 1/4in
Trend dovetail cutters are designed for use with commercial dovetailing and stair housing jigs. Also cutters to produce sliding and lapped dovetails, through dovetails and end on dovetails. Suitable for use on natural timbers and man-made boards, they are used extensively in cabinet work, furniture making, stair trenching, dovetail jointing and carcass construction.T.C.T.1/4in Shank.A = 104° C = 12.7mmD = 13.2 mm
Trend Craft Pro Intumescent Strip Cutter cuts the perfect sized slot into door edges and door frames for fast, perfectly flush fitting of intumescent strip. A bearing guide ensures the correct depth and width is always achieved to meet Fire Regulations. PTFE coating to minimise heat and resin build-up, for increased cutter performance and longevity. All Trend router cutters also have a safety ‘K’ mark insertion indicator on each shank to ensure a quick and easy set up, whether for handheld or table work.Trend C209 x 1/4 TCT Intumescent Recessor to suit 4mm thick strip of 10mm width. Specification: Diameter: 24mmCutting Depth: 10mmBearing: 16mmShank: 1/4in
Designed to meet the needs of both the professional tradesman and the home handyman.All are Tungsten Carbide Tipped, to ensure longevity of working life, coupled with a good quality finish to the work.Ovolo produces a stepped rounded profile along the edge of the material. The guide pin enables the cutter to follow intricate shapes. 1/4in Shank.Radius 6.3mmDepth of Cutter 13.3mmShank Diameter 1/4in
The Trend 50 Piece Router Bit Starter Set contains a range of popular 1/4in tungsten carbide tipped cutters for a variety of applications. Suitable for softwood, hardwood, chipboard, plywood and MDF. Supplied in an aluminium carry case. Contains: 2 x Single Flute Straight: 3 x 12.7mm and 4 x 12.7mm.8 x Two Flute Straight: 6 x 16mm, 8 x 19mm, 9.5 x 19mm, 12.7 x 19mm, 14.2 x 19mm, 15.9 x 19mm, 19 x 19mm and 20 x 19mm.4 x Guided Flush Trim: 9.5 x 12.7mm, 9.5 x 25.4mm, 12.7 x 12.7mm and 12.7 x 25.4mm.1 x Combination Bevel: 12.7mm x 60°.1 x Mortiser Cutter: 12.7 x 12.7mm.1 x Classic Panel Cutter: 12.7 x 9mm.1 x Keyhole Cutter: 9.5mm.3 x Core Box: R3.2, R4.8 and R6.35mm.2 x Long Series Core Box: R4.8 and R6.35mm.2 x 60° V-Groove: 9.5mm and 16mm.2 x 90° V-Groove: 9.5mm and 12.7mm.4 x 14° Dovetail: 9.5mm, 12.7mm, 14.3mm and 16mm.1 x Pierce & Trim: 6.35 x 18mm.2 x Guided Cove: R6.35 and R9.5mm.4 x Guided Round Over: R3.2, R6.3, R7.9 and R9.5mm.4 x Guided Ovolo: R3.2, R6.35, R7.9 and R9.5mm.2 x Guided Roman Ogee: R4 and R6.35mm.2 x Guided Chamfer: 25° and 45°.2 x Guided Slotter: 6.35mm kerf and 9.5mm kerf.1 x Guided Rebater (Ø x cut): 28 x12.7mm, Rebate: 9.5mm.1 x Guided Classic Decor: R9mm.
Trend guide bushes can be attached to the base of the Router. They are designed to follow the contours of a template.Guide bush guides the router when using a template. Fits directly to Trend T3,T4,T5,T5 MK2, T9,T10 and T11, and some other light duty routers. Will fit other makes when used with GB/5, GB/PLATE or UNIBASE Sub-base. GB12 = 12mm, Outside Diameter of Bush.
This Trend 3/2 x 1/4 TCT Two Flute Cutter has the following specification: D: 6.0mm (15/64in)C: 16mmOL: 48mmShank Diameter: 1/4in Trend Two Flute Straight Cutters produce a cleaner finish than the single flute cutters. Suitable for grooving, rebating, morticing, drilling and shallow lateral routing cuts such as recessing hinges. Corners will require a final trimming square with a hand chisel or a corner chisel. Suitable for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.
Integral clamping jaws and a locking lever provide a quick way of clamping the guide batten. It is ideal for holding and clamping work pieces and the aluminium extrusion incorporating T-slots. The clamp is fitted with a metric/imperial scale for setting lengths and stop positions and the scale can be be positioned by removing 20mm of the self adhesive backing.
The manufacturing specification for Faithfull router bit cutters ensures that they are suitable for use by all professional tradesmen, craftsmen and conscientious DIY enthusiasts. Every Faithfull router cutter tip is made from tungsten carbide, brazed onto a steel body and designed to cut a wide variety of timber and abrasive material such as MDF and plywood. With careful handling and under normal conditions, they will outlast HSS grade cutters many times. These top quality cutters will ensure an excellent finish and provide the user with long lasting and reliable service. 1/2in ShankCutting Diameter: 10.0 mm 3/8in. Cutting Length 19 mm Shank Diameter: 1/2in
The manufacturing specification for Faithfull router bit cutters ensures that they are suitable for use by all professional tradesmen, craftsmen and conscientious DIY enthusiasts. Every Faithfull router cutter tip is made from tungsten carbide, brazed onto a steel body and designed to cut a wide variety of timber and abrasive material such as MDF and plywood. With careful handling and under normal conditions, they will outlast HSS grade cutters many times. These top quality cutters will ensure an excellent finish and provide the user with long lasting and reliable service. 1/4in ShankCutting Diameter: 12.7 mm 1/2in. Cutting Length 25 mm Shank Diameter: 1/4in.
The Trend C168 x 1/4TC Guided Trimmer has two flute carbide TCT tips. Used for trimming plastic or plywood overlays. Its 6.3mm diameter allows it to follow more intricate curves. 25.4mm cutting depth for replication of thin components with templates. Fitted with a bottom bearing guide for following an edge to trim laminates and veneers for a professional finish. PTFE coating to minimise heat and resin build-up, for increased cutter performance and longevity. All Trend router cutters also have a safety ‘K’ mark insertion indicator on each shank to ensure a quick and easy set up, whether for handheld or table work.
Starter cutter set containing a range of 15 popular cutters supplied in a plastic carry case. Including: Single flute, two flute, dovetail, guided round and over guided chamfer, rebater, trimmer, cove and roman ogee, v groove and core box cutters. Size: 1/2in shank. Type: tungsten carbide tipped.
Self guiding cutters with bearings mounted for trimming and bevelling timber, lippings and plastic laminate edges for cabinet making, countertop production or any shaping applications. Bearing guided cutters are suitable for both straight and curved work, bearings are normally fractionally larger than cutter diameter, to avoid surface scoring. Uses:Trimming plastic or plywood overlay.Copy profiling - use the bearing to follow a template or base edge of board. A 3 mm approximate overlap should be left before copy profiling, also when using plastic laminate always allow laminate adhesive to dry before trimming. This avoids clogging the guide bearing. Tooling Tungsten Carbide1/2in Shank.Tooling Tungsten Carbide1/4in Shank.Angle A = 90 D = 12.7 mmC = 25 mm
Four piece router bit set for use with kitchen worktop jigs. Tungsten carbide bits suitable for all routers with 1/2in collet. Set contains: 1 Straight Cutter: 12.7mm x 60mm x 1/2in shank 2 Straight Cutters: 12.7mm x 50mm x 1/2in shank 1 Flush Trim Cutter: 12.7mm x 25.4mm x 1/4in shank
Trend Craft Pro Two Fluted Tungsten Carbide Tipped straight cutters are suitable for a wide range of applications such as engraving, grooving, rebating and shallow morticing. They can be used on a wide range of materials such as softwoods, hardwoods, MDF, plywood and chipboard. All cutters are TCT and have a bottom cut feature. When deep cuts are required, more than one pass should be taken. Shank: 1/4inSuitable for a wide range of applications such as engraving, grooving, rebating and shallow morticing. Use on softwoods, hardwoods, MDF, plywood and chipboard. All cutters have a bottom cut feature. D1 1/2 inch D1 12.7 mm Cut length 2 inches Cut length 50 mm Shank Diameter 1/2 inch
The Trend Craft Pro Round Over Cutter is used for edge detailing on curved and straight work with additional bearing for quirked, Ovolo detail option. Its 9.5mm radius will cut a full bullnose profile for detailing work on 19mm stock. 1/4in shank for easy control in smaller routers with 'K' mark shank to ensure safe working practices. Specially designed PTFE coated bodies to minimise heat and resin build-up and Micro-granular Tungsten Carbide tips ensure a premium finish in hard and soft woods, and abrasive man-made boards such as ply, MDF and chipboard, to meet the needs of the woodworker and tradesman for quality and performance.
Trend CO76X1 Rounding over, self-guiding TCT cutter for rounding over edges do not require a side fence with a 6.3 mm radius x 12.7 mm cut. Supplied with two bearings - use the larger bearing for a round-over. If the cutter is lowered, a top quirk can be produced. Bullnose mouldings can also be produced by taking a second pass from the opposite side of the workpiece.
Trend Craft Pro Two Fluted Tungsten Carbide Tipped straight cutters are suitable for a wide range of applications such as engraving, grooving, rebating and shallow morticing. They can be used on a wide range of materials such as softwoods, hardwoods, MDF, plywood and chipboard. All cutters are TCT and have a bottom cut feature. When deep cuts are required, more than one pass should be taken. Shank: 1/4inD - Diameter - 3/8in 9.5mmC - Cutting Length - 3/4in 19.1mmT.C.T. 2 Flutes.
The Trend PH/JIG Pocket Hole Jig is great for fast and accurate joining of timber and plywood, giving strong instant joints. Solid hardened bushes with variable pitch of 29mm to 63mm. Use on timber, MDF, plywood and block board. Allows a variety of joints to be created individually. Uses square drive self tapping screws. Work piece can be handled immediately after gluing and screwing, creating time saving benefits. No clamps required.The Trend PH/JIG Pocket Hole Jig is supplied with: 100 x Dome Head Screws, 1 x Face Clamp, 1 x HSS Drill Bit With Collar, 1 x 75mm Square Drive Bit, 1 x 150mm Square Drive Bit.
The Trend Corner Chisel is used to square up rounded corners on hinge and lock recesses. Fitted with a high speed steel (HSS) anvil. Use with a Hammer. The chisel can be resharpened. Ideal for use with hinge and lock jigs.
The Trend Kitchen Worktop Jig is a hard-wearing solid laminate, 12mm thick jig that enables cutting both parts of the joint in 15 minutes including setting up. The jig has the following features: Left and right hand corners, 400mm radius peninsular joint, 45° end cut with slight radius, 45° trade corner, 40mm radius corner, 35mm kitchen door hole and 3/4inch BSP hole for mixer taps. Engraved lines for 65mm bolts and worktop cross-cut. 6 x 10mm diameter ABS plastic pins with tapered shoulders for a tight fit and 3 point pin contact to ensure ease of setting up.This pack contains 4 spare location pins, which are suitable for the KWJ700 and KWJ900 worktop jigs. Made from ABS plastic for strength.
The Trend Skeleton Hinge Jig is a 2-part, adjustable portable template set designed for recessing hinges in wooden doors and frames with a router. It is easy to use with minimal setting-up time, ensuring that the job can be completed accurately and quickly. It is ideal for use on-site and in joinery shops to increase productivity with excellent results. The jig has fully adjustable apertures for fire door requirements and renovation work. It is ideal for fitting a new door into an old frame, and is suitable for timber based doors and square butt hinges. The jig is supplied with a carry case, bradawls and a special 16mm guide bush. Specifications: Preset hinge sizes: 20mm, 25mm and 30mm. Hinge sizes possible:Minimum length: 67mm (2.5/8in).Maximum length: 127mm (5in).Minimum width: 12.7mm (1/2in).Maximum width: 35mm (1.3/8in). Door sizes possible:Minimum height: 1,956mm (6ft5in).Maximum height: 2,100mm (6ft10in).Minimum thickness: 16mm (5/8in).Maximum thickness: 51mm (2in). Weight: 2.9kg.Overall length: 1,956mm.
The manufacturing specification for Faithfull router bit cutters ensures that they are suitable for use by all professional tradesmen, craftsmen and conscientious DIY enthusiasts. Every Faithfull router cutter tip is made from tungsten carbide, brazed onto a steel body and designed to cut a wide variety of timber and abrasive material such as MDF and plywood. With careful handling and under normal conditions, they will outlast HSS grade cutters many times. These top quality cutters will ensure an excellent finish and provide the user with long lasting and reliable service. 1/2in ShankCutting Diameter: 12.7 mm 1/2in. Cutting Length 32 mm Shank Diameter: 1/2in.
Trend guide bushes can be attached to the base of the Router. They are designed to follow the contours of a template.Trend guide bushes can be attached to the base of the Router. They are designed to follow the contours of a template.. GB30 = 30mm, Outside Diameter of Bush.
Trend C074 x 1/4 TC Round Over Two Flute Cutter. 1/8in imperial radius for matched replication. Leaves perfect fine round over detail for a contemporary eased edge profile on straight and curved edges. Specification: Radius: 3.2mmDepth: 9.5mmOverall Length: 61mmShank: 1/4in
Trend Trade range two flute router cutters have extra long shanks and are designed to meet the demanding needs of the professional trademen. They have a 2mm micrograin Tungsten Carbide tips for cutting the most abrasive materials to give extra long life. They have a PTFE coat, indicated by distinctive black colouring and produce a clean finish to abrasive timbers such as chipboard, MDF, plywood and certain hardwoods. The dimensions are etched on the extra long 40mm shanks for quick identification and are suitable for mortice and worktops applications.TR18D have a centre tip for drilling abrasive materials.Dimensions:Shank: 1/2 inCutting Diameter (D): 12.7mm (1/2 in)Cutting Length (C): 63mm
The manufacturing specification for Faithfull router bit cutters ensures that they are suitable for use by all professional tradesmen, craftsmen and conscientious DIY enthusiasts. Every Faithfull router cutter tip is made from tungsten carbide, brazed onto a steel body and designed to cut a wide variety of timber and abrasive material such as MDF and plywood. With careful handling and under normal conditions, they will outlast HSS grade cutters many times. These top quality cutters will ensure an excellent finish and provide the user with long lasting and reliable service. 1/4in ShankCutting Diameter: 12.0 mm 15/32in. Cutting Length: 19 mm. Shank Diameter: 1/4in.
The Faithfull 12 Piece Router Bit Set with 1/4in shank. Tungsten Carbide tips ensure long life and the storage case provides a safe place to store the bits when they are not being used. Different cutter shapes enable the creation of a variety of profiles, grooves and mouldings in softwoods, hardwoods, MDF or plywood. Shank: 6.3mm (1/4in). Set Contains: (Diameter/Depth) 1 x Dovetail (12.7/13mm).1 x Straight (6/20mm).1 x Straight (12/20mm).1 x Straight (16/20mm).1 x Flush trim (12.7/13mm).1 x Rounding over R7.9mm (25/14mm).1 x Rounding over R9.5mm (28/14mm).1 x Roman ogee R4mm (25/12mm).1 x Core box R6.3mm (12.7/10mm).1 x Cove R6.3mm (22/12mm).1 x 45° Chamfer (32/13mm).1 x 90° V Grooving (12.7/9mm).
The Trend Solid Tungsten Carbide two flute cutters are turned, milled and ground from a solid piece of Tungsten Carbide and provide the greatest durability when used under stress load conditions. They offer better plunge cutting characteristics than TCT.Dimensions:Shank: 1/4inCutting Diameter (D): 6.3mmCutting Length (C): 28.0mm
The Multiscribe is a profile matching tool used to transfer contours from one shape to another and mark on to various materials. 15-functions including parallel scribe, convex scribe, contour profile scribing and line block. Multi-function tool for a variety of marking out applications. For use by all trades, carpenters, joiners, builders etc. Built-in spirit level and pencil sharpener. Steel blade with 5 mm & 1/4 inch graduations for profiling. Patent No. GB2380164. Design Reg. 3021163.
The manufacturing specification for Faithfull router bit cutters ensures that they are suitable for use by all professional tradesmen, craftsmen and conscientious DIY enthusiasts. Every Faithfull router cutter tip is made from tungsten carbide, brazed onto a steel body and designed to cut a wide variety of timber and abrasive material such as MDF and plywood. With careful handling and under normal conditions, they will outlast HSS grade cutters many times. These top quality cutters will ensure an excellent finish and provide the user with long lasting and reliable service. 1/4in ShankCutting Diameter: 22.0 mm 7/8in. Cutting Length 19 mm Shank Diameter: 1/4in.
The manufacturing specification for Faithfull router bit cutters ensures that they are suitable for use by all professional tradesmen, craftsmen and conscientious DIY enthusiasts. Every Faithfull router cutter tip is made from tungsten carbide, brazed onto a steel body and designed to cut a wide variety of timber and abrasive material such as MDF and plywood. With careful handling and under normal conditions, they will outlast HSS grade cutters many times. These top quality cutters will ensure an excellent finish and provide the user with long lasting and reliable service. 1/4in ShankCutting Diameter: 7.0 mm 9/32in. Cutting Length 19 mm Shank Diameter: 1/4in.
