The Trend CR/DWS/CC/FC is a double sided credit card size diamond stone. It has monocrystalline diamonds for fast, clean, stock removal and excellent sharpening performance. Double sided for coarse sharpening and fine honing. Coarse 360 grit (nom. 40 microns) and fine 600 grit (nom. 25 microns). Ideal for fluted, shaped and small router bits, carbide or HSS, turning tools, chisels, plane blades, carving tools and all general tooling. Recommended for use with Trend lapping fluid to prevent clogging or rusting and assist in keeping tools clean.
Trend guide bushes can be attached to the base of the Router. They are designed to follow the contours of a template.Guide bush guides the router when using a template. Fits directly to Trend T3,T4,T5,T5 MK2, T9,T10 and T11, and some other light duty routers. Will fit other makes when used with GB/5, GB/PLATE or UNIBASE Sub-base.
Attractive edge moulds and a full corner bead can be produced by making a second pass at 90° with this TCT cutter. Used on all man-made boards such as medium density fibre board, chipboard, and also natural timbers and most plastics. T.C.T.Shank = 1/4in.R = 4.8 mmD = 26 mmd = 22 mmC = 16 mmB = 15.9 mm Craft Range - They can be used on all man-made boards such as medium density fibre board, chipboard, and also natural timbers and most plastics Bead & Reed Cutters Bead and Reed cutters are ideally suited to form straight or curved decorative edge mouldings on table tops, chair legs and frames. They can also be used to produce complete round over profiles for window boards and stair tread nosings. Cutters can be combined to form compounded one-off mouldings for individual applications. Certain staff bead cutters are used to join boards and produce hinged joints for table tops.
Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. T.C.T. Tooling1/2in Shank.C = 25 mmD = 25.4 mm 1in
Trend 12 Piece Starter Cutter Set containing a range of the most widely used cutters for decorative woodworking. Made from tungsten carbide with 1/4in shanks and supplied in a plastic carry case. 1 x Straight 6.3mm x 16mm1 x Straight 12.7mm x 19mm1 x Dovetail 104° x 1/2in2 x Guided Round Over radius: 6.35mm and 9.5mm1 x Guided Chamfer 45°1 x Guided Rebater 9.5mm1 x Guided Trimmer 12.7mm1 x Guided Cove 6.3mm1 x 'V' Groove 45°1 x Core Box radius 6.35mm1 x Guided Ogee radius 4mm
The Trend Hinge Jig is a portable template set designed for recessing hinges in wooden doors and frames. Used on-site and in joinery shops to increase productivity with excellent results. Four apertures for fire door requirements. No need for marking out in the conventional way. Quick and simple to set-up as the hinge is used as the pattern. Clean and accurate recesses are achieved every time. Suitable for timber based doors and square butt hinges. Use with a light duty router with 1/4inch collet. Long reach router cutter required, 12mm diameter with 70mm overall length. Angled position slots to prevent creep. Patent No. GB2285410. Includes: 4 x Apertures, 2 x Bradawls, 1 x 16mm Guide Bush, 1 x T-Handle Hex Key, 1 x 4mm Spacing Gauge and 1 x Plastic Storage Tube. Specification Hinge Sizes Possible: Length Min/Max: 67-127mm (2.5/8-5in).Width Min/Max: 9.5-35mm (3/8-1.3/8in). Door Sizes Possible: Height Min/Max: 1955-2032mm (6ft 5in - 6ft 10in).Thickness Min/Max: 16-44mm.
Trend Trade range two flute router cutters have extra long shanks and are designed to meet the demanding needs of the professional trademen. They have a 2mm micrograin Tungsten Carbide tips for cutting the most abrasive materials to give extra long life. They have a PTFE coat, indicated by distinctive black colouring and produce a clean finish to abrasive timbers such as chipboard, MDF, plywood and certain hardwoods. The dimensions are etched on the extra long 40mm shanks for quick identification and are suitable for mortice and worktops applications.The TR40D has a center tip for drilling abrasive materials.Dimensions:Shank: 1/4 inCutting Diameter (D): 15mmCutting Length (C): 25mm
Trend Craft Pro Intumescent Strip Cutter cuts the perfect sized slot into door edges and door frames for fast, perfectly flush fitting of intumescent strip. A bearing guide ensures the correct depth and width is always achieved to meet Fire Regulations. PTFE coating to minimise heat and resin build-up, for increased cutter performance and longevity. All Trend router cutters also have a safety ‘K’ mark insertion indicator on each shank to ensure a quick and easy set up, whether for handheld or table work.Trend C220 x 1/4 TCT Intumescent Cutter to suit 4mm thick strip of 15mm width. Specification: Diameter: 24mmCutting Depth: 15mmBearing: 16mmShank: 1/4in
The manufacturing specification for Faithfull router bit cutters ensures that they are suitable for use by all professional tradesmen, craftsmen and conscientious DIY enthusiasts. Every Faithfull router cutter tip is made from tungsten carbide, brazed onto a steel body and designed to cut a wide variety of timber and abrasive material such as MDF and plywood. With careful handling and under normal conditions, they will outlast HSS grade cutters many times. These top quality cutters will ensure an excellent finish and provide the user with long lasting and reliable service. 1/4in ShankCutting Diameter: 15.0 mm 19/32in. Cutting Length 25 mm Shank Diameter: 1/4in.
Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. Two flutes give a clean finish to cut edges. 1/4in Shank.C = 19 mmD = 10 mm 25/64 in
Shell style 90º countersink produced from the best grade carbon steel designed to leave a clean cut finish by virtue of their multi-tooth deep ground gullets. Not suitable for abrasive materials or metals.This TCT Countersink clamps onto any drill between 3 mm and 7.2 mm in diameter. The drill passes through the body of the countersink and is secured by two hexagon bolts which clamp the countersink onto the drill at the required position. Recommended for wood and man made boards.By reversing the countersink on the drill the UNI / CS can be used as a non-cutting depth stop. NOTE:- Drills not included.
Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. T.C.T. Tooling1/2in Shank.Ideal for cutting kitchen worktops. This cutter is especially suited for drilling. C = 50 mmD = 12.7 mm 1/2 in
Tooling for use on webbed aluminium and UPVC extrusions by window and door fabricators. Cutters are produced in special high speed steel (HSSE) to ensure a clean cut and resist the abrasive nature of anodised aluminium extrusions. Cutters are designed to plunge and machine or mill lateral slots All tooling for aluminium should be used with a coolant, wax stick, or lubricant. The material being worked on should always be securely clamped in a machine vice. HSSE.One Flute helical Plunge-slotting bit.8 mm Shank.D = 5 mmC = 12 mmOL = 60 mm
Trend collet reduction sleeve, used to reduce the collet size to take cutters with smaller shanks. Should only be used as a stop-gap, as the correct size collet is recommended. Should not be used for extensive periods or heavy work.The TRE8127 Collet Sleeve has the following specifications:Diameter: 12.7mm (1/2in).Bore: 8mm.Overall length: 30mm.
Trend collet reduction sleeve, used to reduce the collet size to take cutters with smaller shanks. Should only be used as a stop-gap, as the correct size collet is recommended. Should not be used for extensive periods or heavy work.The TRE63127 Collet Sleeve has the following specifications: Diameter: 12.7mm (1/2in)Internal Bore 6.35mm (1/4in)Bore: 8mm.Overall length: 30mm.
Profilers with shank mounted bearings for guidance, for use with router mounted above or below a table when following a template. Bearing guided cutters are suitable for both straight and curved work. For profiling and rebating applications only. NOT for plunge, cutting or grooving. A 3 mm approximate overlap should be left before copy profiling, also when using plastic laminate always allow laminate adhesive to dry before trimming. This avoids clogging the guide bearing.A 3 mm approximate overlap should be left before copy profiling, also when using plastic laminate always allow laminate adhesive to dry before trimming. This avoids clogging the guide bearing. Tooling Tungsten Carbide1/2 in Shank. Angle A = 90° D = 19.1 mmC = 50 mm
These types of cutters are used for edging work and chamfer cutting on man made fibre boards, natural timbers and plastics. Tools are offered to produce various angles for chamfering. Ball bearing and pin guarded cutters enable curved work to be undertaken with bearings running along the board edge or a template. Typical trade applications include sign making, freehand engraving, cabinet making and decorative joinery.T.C.T.1/4in Shank.A = 45° C1 = 12 mmC2 = 16 mmD = 31.8 mmB = 9.5 mm
Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. Two flutes give a clean finish to cut edges. 1/4in Shank.C = 25 mmD = 20 mm 25/32in
Profilers with shank mounted bearings for guidance, for use with router mounted above or below a table when following a template. Bearing guided cutters are suitable for both straight and curved work. For profiling and rebating applications only. NOT for plunge, cutting or grooving. A 3 mm approximate overlap should be left before copy profiling, also when using plastic laminate always allow laminate adhesive to dry before trimming. This avoids clogging the guide bearing.A 3 mm approximate overlap should be left before copy profiling, also when using plastic laminate always allow laminate adhesive to dry before trimming. This avoids clogging the guide bearing.Tooling Tungsten Carbide1/4 in Shank.Angle A = 90 D = 12.7 mmC = 25.4 mm
Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. T.C.T. Tooling1/2in Shank.C = 63 mmD = 12.7 mm 1/2 in
Self guiding cutters with bearings mounted for trimming and bevelling timber, lippings and plastic laminate edges for cabinet making, countertop production or any shaping applications. Bearing guided cutters are suitable for both straight and curved work, bearings are normally fractionally larger than cutter diameter, to avoid surface scoring. Uses:Trimming plastic or plywood overlay.Copy profiling - use the bearing to follow a template or base edge of board. A 3 mm approximate overlap should be left before copy profiling, also when using plastic laminate always allow laminate adhesive to dry before trimming. This avoids clogging the guide bearing. Tooling Tungsten Carbide1/2in Shank.Angle A = 90 D = 12.7 mmC = 50 mm
Two flute TC cutter giving good chip clearance. Ideal for shallow lateral routing cuts such as recessing hinges.Corners will require final trimming square with a hand chisel or a corner chisel. Diameter: 12.7mm.Cutting length: 19mm.Shank: 1/4in.
Trend Craft Pro Two Fluted Tungsten Carbide Tipped straight cutters are suitable for a wide range of applications such as engraving, grooving, rebating and shallow morticing. They can be used on a wide range of materials such as softwoods, hardwoods, MDF, plywood and chipboard. All cutters are TCT and have a bottom cut feature. When deep cuts are required, more than one pass should be taken. Shank: 1/4inDiameter - 1/8in 3.2mmCutting Length - 3/8in 9.5mmT.C.T. 2 Flutes.
Self-guided trimming bits. Used for trimming plastic or plywood overlays. Also for copy profiling with a template. Raise cutter in stages to spread wear of cutting edges TCT. Diameter = 12.7 mmCitting Length = 25.4 mmSelf-guided trimming bits. Used for trimming plastic or plywood overlays. Also for copy profiling with a template. Raise cutter in stages to spread wear of cutting edges D = 9.5 mmC = 12.7 mm
This Trend C172X1/2TC Two Flute Router Cutter has the following specification: Shank: 1/2inDiameter: 12mm (1/2in)Cutting Length: 63mm (2.1/2in)Overall Length: 115mm (
These types of cutters are used for edging work and chamfer cutting on man made fibre boards, natural timbers and plastics. Tools are offered to produce various angles for chamfering. Ball bearing and pin guarded cutters enable curved work to be undertaken with bearings running along the board edge or a template. Typical trade applications include sign making, freehand engraving, cabinet making and decorative joinery.T.C.T.1/2in Shank.A = 45° C1 = 19 mmC2 = 26 mmD = 51.5 mmB = 12.7 mm
Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. T.C.T. Tooling1/2in Shank.T.C.T. Tooling1/2in Shank.C = 25 mmD = 18 mm 45/64 in
Self-guided trimming bits. Used for trimming plastic or plywood overlays. Also for copy profiling with a template. Raise cutter in stages to spread wear of cutting edges TCT. Diameter = 12.7 mmCitting Length = 25.4 mmShank size: 1/4in.
The manufacturing specification for Faithfull router bit cutters ensures that they are suitable for use by all professional tradesmen, craftsmen and conscientious DIY enthusiasts. Every Faithfull router cutter tip is made from tungsten carbide, brazed onto a steel body and designed to cut a wide variety of timber and abrasive material such as MDF and plywood. With careful handling and under normal conditions, they will outlast HSS grade cutters many times. These top quality cutters will ensure an excellent finish and provide the user with long lasting and reliable service. 1/4in ShankCutting Diameter: 15.9 mm 5/8in. Cutting Length: 19 mm. Shank Diameter: 1/4in.
Trend Bearing Guided Template Profile Cutter for rebating and trimming edges. Extra care must be taken to avoid breakage of the cutter. Two flute carbide TCT tips for clean, professional finish on timber lippings, plastic laminates and veneers. Specially designed PTFE coated bodies to minimise heat and resin build-up and Micro-granular Tungsten Carbide tips ensure a premium finish in hard and soft woods, and abrasive man-made boards such as ply, MDF and chipboard, to meet the needs of the woodworker and tradesman for quality and performance. All Trend router cutters also have a safety ‘K’ mark insertion indicator on each shank to ensure a quick and easy set up whether for hand held or table work.This Trend Bearing Guided Template Profile Cutter has the following specification: (D) Diameter: 12.7mm(C) Cutting Length: 25.4mmShank: 1/4in
Trend C056A TCT Radius Cove Cutter with two flutes and carbide TCT tips for a cleaner cut and fast clearance of waste in all timber and timber-based materials. 9.5mm radius, 12.7mm cut depth for classic decorative mouldings and edge details. 1/2in shank ideal for heavy-duty applications and router table use, with a 'K' marked shank to ensure safe working practices. PTFE coating to minimise heat and resin build-up for increased cutter performance and longevity. Specification: Radius: 9.5mmCutting Depth: 12.7mmShank: 1/2in
Collets designed to fit DEWALT routers.The DEWALT DE6952 Replacement Router Collet is suitable for the following DEWALT machines: DW609, DW613, DW614, DW615, DW620, DW621/K, D26204/K, D26200 & D26203 routers. Collet Size: 8mm.
Trend guide bushes can be attached to the base of the Router. They are designed to follow the contours of a template.Guide bush guides the router when using a template. Fits directly to Trend T3,T4,T5,T5 MK2, T9,T10 and T11, and some other light duty routers. Will fit other makes when used with GB/5, GB/PLATE or UNIBASE Sub-base. GB12 = 12mm, Outside Diameter of Bush.
Trend guide bushes can be attached to the base of the Router. They are designed to follow the contours of a template.Guide bush guides the router when using a template. Fits directly to Trend T3,T4,T5,T5 MK2, T9,T10 and T11, and some other light duty routers. Will fit other makes when used with GB/5, GB/PLATE or UNIBASE Sub-base. GB18 = 18mm, Outside Diameter of Bush.
Replacement bearing to suit all Trend bearing guided router cutters. The Bearings are shielded to prevent penetration of dust and grease packed for life and should not be cleaned with solvent or lubricated as this will dissolve the grease and cause premature bearing failure.Outside Diameter:- 1/2inInside Diameter:- 1/4inThickness:- 3/16in
