Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. T.C.T. Tooling1/2in Shank.T.C.T. Tooling1/2in Shank.C = 50 mmD = 12 mm 15/32 in
Trend C056A TCT Radius Cove Cutter with two flutes and carbide TCT tips for a cleaner cut and fast clearance of waste in all timber and timber-based materials. 9.5mm radius, 12.7mm cut depth for classic decorative mouldings and edge details. 1/2in shank ideal for heavy-duty applications and router table use, with a 'K' marked shank to ensure safe working practices. PTFE coating to minimise heat and resin build-up for increased cutter performance and longevity. Specification: Radius: 9.5mmCutting Depth: 12.7mmShank: 1/2in
Trend Craft Pro Two Fluted Tungsten Carbide Tipped straight cutters are suitable for a wide range of applications such as engraving, grooving, rebating and shallow morticing. They can be used on a wide range of materials such as softwoods, hardwoods, MDF, plywood and chipboard. All cutters are TCT and have a bottom cut feature. When deep cuts are required, more than one pass should be taken. Shank: 1/4inSuitable for a wide range of applications such as engraving, grooving, rebating and shallow morticing. Use on softwoods, hardwoods, MDF, plywood and chipboard. All cutters have a bottom cut feature. D1 1/2 inch D1 12.7 mm Cut length 2 inches Cut length 50 mm Shank Diameter 1/2 inch
Profilers with shank mounted bearings for guidance, for use with router mounted above or below a table when following a template. Bearing guided cutters are suitable for both straight and curved work. For profiling and rebating applications only. NOT for plunge, cutting or grooving. A 3 mm approximate overlap should be left before copy profiling, also when using plastic laminate always allow laminate adhesive to dry before trimming. This avoids clogging the guide bearing.A 3 mm approximate overlap should be left before copy profiling, also when using plastic laminate always allow laminate adhesive to dry before trimming. This avoids clogging the guide bearing.Tooling Tungsten Carbide1/4 in Shank.Angle A = 90 D = 12.7 mmC = 9.5 mm
A bearing guided tungsten carbide tipped cutter designed to produce a decorative edge when working on MDF, softwoods, hardwoods, and plywood. 1/4in Shank Radius: 3.2mm Diameter: 22mm
Tooling for use on webbed aluminium and UPVC extrusions by window and door fabricators. Cutters are produced in special high speed steel (HSSE) to ensure a clean cut and resist the abrasive nature of anodised aluminium extrusions. Cutters are designed to plunge and machine or mill lateral slots All tooling for aluminium should be used with a coolant, wax stick, or lubricant. The material being worked on should always be securely clamped in a machine vice. HSSE.One Flute helical Plunge-slotting bit.8 mm Shank.D = 6 mmC = 14 mmOL = 60 mm
Trend Craft Pro Two Fluted Tungsten Carbide Tipped straight cutters are suitable for a wide range of applications such as engraving, grooving, rebating and shallow morticing. They can be used on a wide range of materials such as softwoods, hardwoods, MDF, plywood and chipboard. All cutters are TCT and have a bottom cut feature. When deep cuts are required, more than one pass should be taken. Shank: 1/4inD - Diameter - 15/32in 12.0mmC - Cutting Length - 3/4in 19.1mmT.C.T. 2 Flutes
Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. T.C.T. Tooling1/2in Shank.T.C.T. 1/2 in Shank.C = 25 mmD = 19.1mm 3/4in
Cutter Set Ref. 348 is used for the grooving of door edges to receive 10mm intumescent strip. The arbor can be lowered or raised to give a wider groove for 20mm strip. Choose alternative bearings to suit other thicknesses of intumescent strip. D1 40 mm Cut length 15 mm B 32 mm E 4 mm L 41 mm Shank Diameter 1/2 inch.
The manufacturing specification for Faithfull router bit cutters ensures that they are suitable for use by all professional tradesmen, craftsmen and conscientious DIY enthusiasts. Every Faithfull router cutter tip is made from tungsten carbide, brazed onto a steel body and designed to cut a wide variety of timber and abrasive material such as MDF and plywood. With careful handling and under normal conditions, they will outlast HSS grade cutters many times. These top quality cutters will ensure an excellent finish and provide the user with long lasting and reliable service. Tungsten carbide cutting edges and bearing guided, making these trimmers ideal for professional and DIY use. Used when trimming timber, lippings and plastic laminates.Type: Flush Trimmer 2 flute Cutting Diameter: 6.3 mm 1/4in Cutting Length: 25.4 mm Shank Diameter: 1/4in
Tungsten carbide cutting edges, suitable for DIY and Professional use. The guide bearing can follow complex and intricate shapes and the cutters are suitable for use on softwoods, hardwoods, MDF and plywood.Supplied with 2 bearings 9.5 and 12.7 mm to enable use as either ovolo or rounding over bits.Diameter 32 mmRadius 9.5 mmDepth 16 mmShank 1/4in
The Trend Loc block workpiece is a pack of four interlocking gripping blocks that lock together to allow the workpiece to be held in place when sanding, drilling and finishing. No need to use clamps. Sets-up in seconds by gripping the workpiece and bench raising the workpiece from the bench, to allow complete access to every edge. Size when four blocks interlocked 173mm x 173mm.
The Trend CDJ300 Craft Dovetail Jig is accurate and easy-to-use for a variety of elegant dovetail joints. It cuts 12.7mm (1/2in) wide half blind dovetails or rebated dovetails in one operation. The CDJ300 is precision made laser cut zinc plated steel template with packing piece. Please note a Unibase and fine height adjuster may be required for certain makes of router. Supplied with: 1 x 1/4in shank TCT 104º Dovetail Cutter and 1 x 15.8mm Guide Bush. Specification Rating: Craftsman.Dovetail Size: 12.7mm.Workpiece Width Max: 300mm.Workpiece Thickness Min: 12mm.Workpiece Thickness Max: 25mm.Guide Bush Size: 15.8mm.Router Base Diameter Max: 180mm.
This cutter is self guiding and can be used to produce rebates, lapjoints, tongues and rebated corners. Alternative bearings can be purchased to vary the rebate. Diameter . 35.0mm.C = 12.7mm.E = 11.1mm.B = 12.7mm. T.C.T.1/4IN Shank.
Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. T.C.T. Tooling1/2in Shank.T.C.T. Tooling1/2in Shank.C = 25 mmD = 18 mm 45/64 in
Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. T.C.T. Tooling1/2in Shank.T.C.T. Tooling1/2in Shank.C = 19 mmD = 8 mm 5/16 in
The manufacturing specification for Faithfull router bit cutters ensures that they are suitable for use by all professional tradesmen, craftsmen and conscientious DIY enthusiasts. Every Faithfull router cutter tip is made from tungsten carbide, brazed onto a steel body and designed to cut a wide variety of timber and abrasive material such as MDF and plywood. With careful handling and under normal conditions, they will outlast HSS grade cutters many times. These top quality cutters will ensure an excellent finish and provide the user with long lasting and reliable service. 1/4in ShankCutting Diameter: 20.0 mm 25/32in. Cutting Length 25 mm Shank Diameter: 1/4in.
Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. T.C.T. Tooling1/2in Shank.C = 25 mmD = 20 mm 25/32 in
Trend Craft Pro Two Fluted Tungsten Carbide Tipped straight cutters are suitable for a wide range of applications such as engraving, grooving, rebating and shallow morticing. They can be used on a wide range of materials such as softwoods, hardwoods, MDF, plywood and chipboard. All cutters are TCT and have a bottom cut feature. When deep cuts are required, more than one pass should be taken. Shank: 1/4inD1 3/8 inch D1 9.5 mm Cut length 1 inch Cut length 25.4 mm Shank Diameter 1/4 inch
Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. Two flutes give a clean finish to cut edges. 1/4in Shank.C = 19 mmD = 25.4 mm 1in
These plug cutters are designed to exactly fit the counterbored holes produced by group 62 and 63 Trend cutters. Recommended speed - 1,000-20,000 /min.TC1/4in Shank. Plug Depth Max. 16mmPlug Depth Min. 12mmPlug Body Diameter. 12mm
Tooling for use on webbed aluminium and UPVC extrusions by window and door fabricators. Cutters are produced in special high speed steel (HSSE) to ensure a clean cut and resist the abrasive nature of anodised aluminium extrusions. Cutters are designed to plunge and machine or mill lateral slots All tooling for aluminium should be used with a coolant, wax stick, or lubricant. The material being worked on should always be securely clamped in a machine vice. HSSE.One Flute helical Plunge-slotting bit.8 mm Shank.D = 8 mmC = 14 mmOL = 120 mm
These Cutters produce recesses with a lower rebate - double rebate. Designed to accept library/bookcase strip (Tonk Strip).Tooling : T.C.T.1/2in Shank.D1 = 9.5 mmD2 = 19 mmC1 = 13 mmC2 = 6 mm
Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. T.C.T. Tooling1/2in Shank.T.C.T. Tooling1/2in Shank.C = 25 mmD = 6.3 1/4 in
