The Trend CR/DWS/CC/FC is a double sided credit card size diamond stone. It has monocrystalline diamonds for fast, clean, stock removal and excellent sharpening performance. Double sided for coarse sharpening and fine honing. Coarse 360 grit (nom. 40 microns) and fine 600 grit (nom. 25 microns). Ideal for fluted, shaped and small router bits, carbide or HSS, turning tools, chisels, plane blades, carving tools and all general tooling. Recommended for use with Trend lapping fluid to prevent clogging or rusting and assist in keeping tools clean.
Collets designed to fit DEWALT routers.The DEWALT DE6952 Replacement Router Collet is suitable for the following DEWALT machines: DW609, DW613, DW614, DW615, DW620, DW621/K, D26204/K, D26200 & D26203 routers. Collet Size: 8mm.
Trend guide bushes can be attached to the base of the Router. They are designed to follow the contours of a template.Guide bush guides the router when using a template. Fits directly to Trend T3,T4,T5,T5 MK2, T9,T10 and T11, and some other light duty routers. Will fit other makes when used with GB/5, GB/PLATE or UNIBASE Sub-base. GB12 = 12mm, Outside Diameter of Bush.
Trend guide bushes can be attached to the base of the Router. They are designed to follow the contours of a template.Guide bush guides the router when using a template. Fits directly to Trend T3,T4,T5,T5 MK2, T9,T10 and T11, and some other light duty routers. Will fit other makes when used with GB/5, GB/PLATE or UNIBASE Sub-base. GB18 = 18mm, Outside Diameter of Bush.
Trend Craft Pro Two Fluted Tungsten Carbide Tipped straight cutters are suitable for a wide range of applications such as engraving, grooving, rebating and shallow morticing. They can be used on a wide range of materials such as softwoods, hardwoods, MDF, plywood and chipboard. All cutters are TCT and have a bottom cut feature. When deep cuts are required, more than one pass should be taken. Shank: 1/4inDiameter - 1/8in 3.2mmCutting Length - 3/8in 9.5mmT.C.T. 2 Flutes.
Replacement bearing to suit all Trend bearing guided router cutters. The Bearings are shielded to prevent penetration of dust and grease packed for life and should not be cleaned with solvent or lubricated as this will dissolve the grease and cause premature bearing failure.Outside Diameter:- 1/2inInside Diameter:- 1/4inThickness:- 3/16in
Trend collet reduction sleeve, used to reduce the collet size to take cutters with smaller shanks. Should only be used as a stop-gap, as the correct size collet is recommended. Should not be used for extensive periods or heavy work.The TRE63127 Collet Sleeve has the following specifications: Diameter: 12.7mm (1/2in)Internal Bore 6.35mm (1/4in)Bore: 8mm.Overall length: 30mm.
Self guiding cutters with bearings mounted for trimming and bevelling timber, lippings and plastic laminate edges for cabinet making, countertop production or any shaping applications. Bearing guided cutters are suitable for both straight and curved work, bearings are normally fractionally larger than cutter diameter, to avoid surface scoring. Uses:Trimming plastic or plywood overlay.Copy profiling - use the bearing to follow a template or base edge of board. A 3 mm approximate overlap should be left before copy profiling, also when using plastic laminate always allow laminate adhesive to dry before trimming. This avoids clogging the guide bearing. Tooling Tungsten Carbide1/2in Shank.Angle A = 90 D = 12.7 mmC = 50 mm
The manufacturing specification for Faithfull router bit cutters ensures that they are suitable for use by all professional tradesmen, craftsmen and conscientious DIY enthusiasts. Every Faithfull router cutter tip is made from tungsten carbide, brazed onto a steel body and designed to cut a wide variety of timber and abrasive material such as MDF and plywood. With careful handling and under normal conditions, they will outlast HSS grade cutters many times. These top quality cutters will ensure an excellent finish and provide the user with long lasting and reliable service. 1/2in ShankCutting Diameter: 10.0 mm 3/8in. Cutting Length 19 mm Shank Diameter: 1/2in
The manufacturing specification for Faithfull router bit cutters ensures that they are suitable for use by all professional tradesmen, craftsmen and conscientious DIY enthusiasts. Every Faithfull router cutter tip is made from tungsten carbide, brazed onto a steel body and designed to cut a wide variety of timber and abrasive material such as MDF and plywood. With careful handling and under normal conditions, they will outlast HSS grade cutters many times. These top quality cutters will ensure an excellent finish and provide the user with long lasting and reliable service. 1/4in ShankCutting Diameter: 4.0 mm 5/32in. Cutting Length: 11 mm. Shank Diameter: 1/4in.
This two wing slotting cutter is ideal for grooving and rebating operations. A 1/2in diameter bearing is supplied with every cutter. Depth of cut can be changed by purchasing alternative bearing sizes. T.C.T.Shank = 1/4in.C = 6.3 mm (Slots) Depth with standard cutter = 3/8in.
Tooling for use on webbed aluminium and UPVC extrusions by window and door fabricators. Cutters are produced in special high speed steel (HSSE) to ensure a clean cut and resist the abrasive nature of anodised aluminium extrusions. Cutters are designed to plunge and machine or mill lateral slots All tooling for aluminium should be used with a coolant, wax stick, or lubricant. The material being worked on should always be securely clamped in a machine vice. HSSE.One Flute helical Plunge-slotting bit.8 mm Shank.D = 5 mmC = 12 mmOL = 60 mm
Trend Trade range two flute router cutters have extra long shanks and are designed to meet the demanding needs of the professional trademen. They have a 2mm micrograin Tungsten Carbide tips for cutting the most abrasive materials to give extra long life. They have a PTFE coat, indicated by distinctive black colouring and produce a clean finish to abrasive timbers such as chipboard, MDF, plywood and certain hardwoods. The dimensions are etched on the extra long 40mm shanks for quick identification and are suitable for mortice and worktops applications.The TR40D has a center tip for drilling abrasive materials.Dimensions:Shank: 1/4 inCutting Diameter (D): 15mmCutting Length (C): 25mm
Trend D-Namic two flute cutters with extra long shanks for deep grooving, rebating and morticing which are useful for template work when thickness of template restricts depth. Extra care must be taken to avoid breakage. Take more passes than usual and only cut up to half the diameter of the cutter in one pass.C = 12 mmD = 19 mm 15/32 inOL = 66mm
Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. Two flutes give a clean finish to cut edges. 1/4in Shank.C = 11 mmD = 3.2 mm 1/8 in
Self guiding cutters with bearings mounted for trimming and bevelling timber, lippings and plastic laminate edges for cabinet making, countertop production or any shaping applications. Bearing guided cutters are suitable for both straight and curved work, bearings are normally fractionally larger than cutter diameter, to avoid surface scoring. Uses:Trimming plastic or plywood overlay.Copy profiling - use the bearing to follow a template or base edge of board. A 3 mm approximate overlap should be left before copy profiling, also when using plastic laminate always allow laminate adhesive to dry before trimming. This avoids clogging the guide bearing. Tooling Tungsten Carbide1/2in Shank.Tooling Tungsten Carbide1/4in Shank. Angle A = 90° D = 6.3 mmC = 12.7 mm
The manufacturing specification for Faithfull router bit cutters ensures that they are suitable for use by all professional tradesmen, craftsmen and conscientious DIY enthusiasts. Every Faithfull router cutter tip is made from tungsten carbide, brazed onto a steel body and designed to cut a wide variety of timber and abrasive material such as MDF and plywood. With careful handling and under normal conditions, they will outlast HSS grade cutters many times. These top quality cutters will ensure an excellent finish and provide the user with long lasting and reliable service. 1/4in ShankCutting Diameter: 9.0 mm 11/32in. Cutting Length 19 mm Shank Diameter: 1/4in.
The manufacturing specification for Faithfull router bit cutters ensures that they are suitable for use by all professional tradesmen, craftsmen and conscientious DIY enthusiasts. Every Faithfull router cutter tip is made from tungsten carbide, brazed onto a steel body and designed to cut a wide variety of timber and abrasive material such as MDF and plywood. With careful handling and under normal conditions, they will outlast HSS grade cutters many times. These top quality cutters will ensure an excellent finish and provide the user with long lasting and reliable service. 1/4in ShankCutting Diameter: 8.0 mm 5/16in. Cutting Length: 19 mm. Shank Diameter: 1/4in.
Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. Two flutes give a clean finish to cut edges. 1/4in Shank.C = 12mmD = 19mm
Ovollo and rounding over bearing guided cutters are ideal for curved work, they can be used on natural timbers, man-made particles and fibre boards. Popular uses include edging window frames, glazing bars, cabinets, table tops, pencil rounds, trophies, shelves and fire surrounds. They can also be used to produce bullnose edge moulds. All cutters supplied with two bearings, larger bearing removes the quirk producing a round over profile.Tooling : T.C.T.1/4in Shank.R = 4.8 mmD = 22 mmC = 12.7 mmBearings = 9.5 and 12.7 mm
These types of cutters are used for edging work and chamfer cutting on man made fibre boards, natural timbers and plastics. Tools are offered to produce various angles for chamfering. Ball bearing and pin guarded cutters enable curved work to be undertaken with bearings running along the board edge or a template. Typical trade applications include sign making, freehand engraving, cabinet making and decorative joinery.T.C.T.1/2in Shank.A = 45° C1 = 19 mmC2 = 26 mmD = 51.5 mmB = 12.7 mm
Self-guided trimming bits. Used for trimming plastic or plywood overlays. Also for copy profiling with a template. Raise cutter in stages to spread wear of cutting edges TCT. Diameter = 12.7 mmCitting Length = 25.4 mmShank size: 1/2in.
Trend Craft Pro Two Fluted Tungsten Carbide Tipped straight cutters are suitable for a wide range of applications such as engraving, grooving, rebating and shallow morticing. They can be used on a wide range of materials such as softwoods, hardwoods, MDF, plywood and chipboard. All cutters are TCT and have a bottom cut feature. When deep cuts are required, more than one pass should be taken. Shank: 1/4inD - Diameter - 3/8 in 9.5mmC - Cutting Length - 1 1/4in 31.8mmT.C.T. 2 Flutes.
Profilers with shank mounted bearings for guidance, for use with router mounted above or below a table when following a template. Bearing guided cutters are suitable for both straight and curved work. For profiling and rebating applications only. NOT for plunge, cutting or grooving. A 3 mm approximate overlap should be left before copy profiling, also when using plastic laminate always allow laminate adhesive to dry before trimming. This avoids clogging the guide bearing.A 3 mm approximate overlap should be left before copy profiling, also when using plastic laminate always allow laminate adhesive to dry before trimming. This avoids clogging the guide bearing.Tooling Tungsten Carbide1/4 in Shank.Angle A = 90 D = 12.7 mmC = 25.4 mm
The manufacturing specification for Faithfull router bit cutters ensures that they are suitable for use by all professional tradesmen, craftsmen and conscientious DIY enthusiasts. Every Faithfull router cutter tip is made from tungsten carbide, brazed onto a steel body and designed to cut a wide variety of timber and abrasive material such as MDF and plywood. With careful handling and under normal conditions, they will outlast HSS grade cutters many times. These top quality cutters will ensure an excellent finish and provide the user with long lasting and reliable service. 1/2in ShankCutting Diameter: 12.7 mm 1/2in. Cutting Length 32 mm Shank Diameter: 1/2in.
Trend Craft Pro Two Fluted Tungsten Carbide Tipped straight cutters are suitable for a wide range of applications such as engraving, grooving, rebating and shallow morticing. They can be used on a wide range of materials such as softwoods, hardwoods, MDF, plywood and chipboard. All cutters are TCT and have a bottom cut feature. When deep cuts are required, more than one pass should be taken. Shank: 1/4inD - Diameter - 5/32in 4.0mmC - Cutting Length - 7/16in 11.1mmT.C.T. 2 Flutes.
Trend C074 x 1/4 TC Round Over Two Flute Cutter. 1/8in imperial radius for matched replication. Leaves perfect fine round over detail for a contemporary eased edge profile on straight and curved edges. Specification: Radius: 3.2mmDepth: 9.5mmOverall Length: 61mmShank: 1/4in
Trend Craft Pro Intumescent Strip Cutter cuts the perfect sized slot into door edges and door frames for fast, perfectly flush fitting of intumescent strip. A bearing guide ensures the correct depth and width is always achieved to meet Fire Regulations. PTFE coating to minimise heat and resin build-up, for increased cutter performance and longevity. All Trend router cutters also have a safety ‘K’ mark insertion indicator on each shank to ensure a quick and easy set up, whether for handheld or table work.Trend C220 x 1/4 TCT Intumescent Cutter to suit 4mm thick strip of 15mm width. Specification: Diameter: 24mmCutting Depth: 15mmBearing: 16mmShank: 1/4in
Trend Craft Pro Two Fluted Tungsten Carbide Tipped straight cutters are suitable for a wide range of applications such as engraving, grooving, rebating and shallow morticing. They can be used on a wide range of materials such as softwoods, hardwoods, MDF, plywood and chipboard. All cutters are TCT and have a bottom cut feature. When deep cuts are required, more than one pass should be taken. Shank: 1/4inD - Diameter - 1/4in 6.3mmC - Cutting Length - 3/4in 19.1mmT.C.T. 2 Flutes.
Ovollo and rounding over bearing guided cutters are ideal for curved work, they can be used on natural timbers, man-made particles and fibre boards. Popular uses include edging window frames, glazing bars, cabinets, table tops, pencil rounds, trophies, shelves and fire surrounds. They can also be used to produce bullnose edge moulds. All cutters supplied with two bearings, larger bearing removes the quirk producing a round over profile.Tooling : T.C.T.1/4in Shank.R = 6.3 mmD = 25.4 mmC = 13 mmBearings = 9.5 and 12.7 mm
The Faithfull Router Bit TCT 45° Chamfer is a bearing guided tungsten carbide tipped cutter producing a 45° chamfer to a maximum depth of 10mm. Suitable for use on softwood, hardwood and all man-made boards. 1/4in Shank
Hinge Sinkers for drilling machines. TCT Hinge sinking cutter for pillar drills only. Designed for recessing holes in melamine covered chipboard to receive circular hinges. Diameter. 35mm.Shank. 8mm.
Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. T.C.T. Tooling1/2in Shank.T.C.T. Tooling1/2in Shank.C = 32 mmD = 12.7 mm 1/2 in
Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. Two flutes give a clean finish to cut edges. 1/4in Shank.Use High Speed tooling when working with softwoods such as Pine. H.S.S Tooling1/4in Shank.C = 28 mmD = 6.3 mm 1/4 in
The Trend Kitchen Worktop Jig is a hard-wearing solid laminate, 12mm thick jig that enables cutting both parts of the joint in 15 minutes including setting up. The jig has the following features: Left and right hand corners, 400mm radius peninsular joint, 45° end cut with slight radius, 45° trade corner, 40mm radius corner, 35mm kitchen door hole and 3/4inch BSP hole for mixer taps. Engraved lines for 65mm bolts and worktop cross-cut. 6 x 10mm diameter ABS plastic pins with tapered shoulders for a tight fit and 3 point pin contact to ensure ease of setting up.The KWJ700 has fixed lengths for 250mm, 300mm, 400mm, 500mm, 550mm, 600mm, 616mm, 650mm and 700mm worktops. Length: 985mm.Width: 390mm.Thickness: 12 mm.Weight: 5.4 kg.End Cut: 45°.Corner Radii: 40mm, 100mm and 400mm.Corner Mitre Joint: 45°.Female cut material width loss: 35 mm.
