Combination pierce and trim cutters. These cutters pierce and cut out aperture in laminate worktops. The base of the cutter acts as a guide follower. Single Flute cutters. Single Flute cutters.Cutting Length: 18mm, Diameter: 6.3mm.Shank. 1/4in.
Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. T.C.T. Tooling1/2in Shank.C = 25 mmD = 25.4 mm 1in
Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. Two flutes give a clean finish to cut edges. 1/4in Shank.C = 4.5 mmD = 11 mm
Ovollo and rounding over bearing guided cutters are ideal for curved work, they can be used on natural timbers, man-made particles and fibre boards. Popular uses include edging window frames, glazing bars, cabinets, table tops, pencil rounds, trophies, shelves and fire surrounds. They can also be used to produce bullnose edge moulds. All cutters supplied with two bearings, larger bearing removes the quirk producing a round over profile.Tooling : T.C.T.1/2in Shank.R = 6.3 mmD = 25.4 mmC = 13 mmBearings = 9.5 and 12.7 mm
Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. Two flutes give a clean finish to cut edges. 1/4in Shank.C = 16 mmD = 5 mm 13/64in
The Trend CR/DWS/F4/FC is a 4 inch double sided diamond stone with folding handle and monocrystalline diamonds for fast, clean, stock removal which gives excellent sharpening performance. It is double sided for coarse sharpening and fine honing: Coarse 360 grit (nom. 40 microns) and fine 600 grit (nom. 25 microns). The Coarse is ideal for carpentry as it rapidly fixes or restores a damaged edge or blunt tools, including chisels and plane irons. The Fine is ideal for cabinet making for a fine finish and refines the cutting edges of chisels, small knives, etc - achieves a razor edge in seconds. With plastic ABS folding handle, that folds to protects diamond surface and oval holes design to collect and hold metal residue. Ideal for saw blades, chisels, knives, domestic and garden tools. Recommended use with Trend lapping fluid to prevent clogging or rusting and assist in keeping tools clean.
Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. Two flutes give a clean finish to cut edges. 1/4in Shank.C = 19 mmD = 8 mm 5/16in
The world's fastest professional worktop scriber tool. It completes traditional scribing chores with precision, speed and ease. Quick and easy-to-use by remaining stable whilst scribing directly onto work-surfaces, flooring, shelves etc. It works by running a wheeled scribe unit along an irregular feature. The sprung pencil in its centre will accurately copy the profile directly onto the work-piece to be installed. It can then be cut and fitted to the surface resulting in a perfect butt! Four sizes of quick fit track wheels to cope with a variety of situations. Design Reg. No. 3014615. Includes: 1 x pencil, 1 x body, 1 x 29 mm wheel, 1 x 50 mm wheel, 1 x 70 mm wheel, 1 x 90 mm wheel.
Trend GAUGE/D60 Digital depth gauge for router tables and saw benches. Horizontal and vertical measuring, ideal for hand routers, router tables and saw benches. It has an LCD readout for mm, imperial and fractions with auto shut off 5 mins. The removable pin allows hole depths to be measured, the pin can be parked on arm. Hole depth 50.8mm (2 inch).
The Trend Door Stand holds door on its edge while routing hinge recess and mortice for locks. Holds door securely. Non-scratch base. Adjustable clamp for doors 32 to 55mm thick. Allows door to be tilted back to assist fitting into frame. Maximum door weight 50kg.
Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. Two flutes give a clean finish to cut edges. 1/4in Shank.C = 25 mmD = 18 mm 45/64in
Rota-Tip Cutters are highly economical for use in production applications.The blades, which are manufactured from a harder grade of Tungsten Carbide than conventional tooling are rotated to expose a new cutting edge ensuring the diameter of the tool remains constant.Blades are replaced when all edges become chipped or dull.The blades are fixed directly onto the tool bodies using torx screws and may be replaced without removing the cutter from the router.All Rota-Tip cutters are supplied with blade(s) fitted and a torx key.T.C.T.1/2in Shank.29.5mm Cut. 89 mm O/L
The jig requires a router fitted with a 30 mm guide bush and 12 mm diameter long reach cutter. For most common sash mortice and dead locks with up to 3in deep mortices and a 7/8in or 1in face plate. Deeper mortices can be achieved with a suitable size of auger bit. Also suits face plate on a 1in mortice latch. NOTE. Use on doors 34 to 58mm thick
Trend Craft Pro Two Fluted Tungsten Carbide Tipped straight cutters are suitable for a wide range of applications such as engraving, grooving, rebating and shallow morticing. They can be used on a wide range of materials such as softwoods, hardwoods, MDF, plywood and chipboard. All cutters are TCT and have a bottom cut feature. When deep cuts are required, more than one pass should be taken. Shank: 1/4inThe Trend CO12AX two flute router cutter is suitable for a wide range of applications such as engraving, grooving, rebating and shallow morticing. Ideal for use on softwoods, hardwoods, MDF, plywood and chipboard.All cutters have a bottom cut feature.Diameter: 8 mm.Cutting Depth: 25 mm.Shank Diameter: 1/4 in.
Trend Craft Pro Two Fluted Tungsten Carbide Tipped straight cutters are suitable for a wide range of applications such as engraving, grooving, rebating and shallow morticing. They can be used on a wide range of materials such as softwoods, hardwoods, MDF, plywood and chipboard. All cutters are TCT and have a bottom cut feature. When deep cuts are required, more than one pass should be taken. Shank: 1/4inD - Diameter - 3/4in 19.1mmC - Cutting Length - 1.0in 25.4mmT.C.T. 2 Flutes
This Trend C172X1/2TC Two Flute Router Cutter has the following specification: Shank: 1/2inDiameter: 12mm (1/2in)Cutting Length: 63mm (2.1/2in)Overall Length: 115mm (
The Trend Anglefix Mitre Guide halves the angle for mitre joints and is ideal for mitre cutting of frames, skirting, architrave and beading as well as basic marking out. It halves angles to achieve correct cutting angle before cutting mitres and sets internal and external angles.Can be used with hand mitre and snip-off saws.Patent No. PCT WO 00/67969.
Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. T.C.T. Tooling1/2in Shank.C = 63 mmD = 15.9 mm - 5/8in
Collets designed to fit DEWALT routers.The DEWALT DE6952 Replacement Router Collet is suitable for the following DEWALT machines: DW609, DW613, DW614, DW615, DW620, DW621/K, D26204/K, D26200 & D26203 routers. Collet Size: 8mm.
Ovollo and rounding over bearing guided cutters are ideal for curved work, they can be used on natural timbers, man-made particles and fibre boards. Popular uses include edging window frames, glazing bars, cabinets, table tops, pencil rounds, trophies, shelves and fire surrounds. They can also be used to produce bullnose edge moulds. All cutters supplied with two bearings, larger bearing removes the quirk producing a round over profile.Tooling : T.C.T.1/4in Shank.R = 6.3 mmD = 25.4 mmC = 13 mmBearings = 9.5 and 12.7 mm
Ref 334 recessing cutter will accomodate the Schlegal Aquamac 21 seal. This cutter is designed for use with the Aquamac seal in a wiping mode and comes complete with a guide bearing to reduce setting up time and simplify machining operations.Alternatively bearing Ref B35C is available to use the cutter for seals fitted in a compression mode of the seal.This larger bearing removes the rebate. TCT.Tooling : 1/2 ShankD = 54.5 mmd = 34.3 mmC1 = 10.3 mmC2 = 2.7 mmB = 28.5 mmOL = 90 mm
This TCT two wing slotting cutter is ideal for biscuit jointing sizes The set is supplied with 3 ball bearing guides to suit the three sizes of biscuits available. A slighlty longer cut than the length of the biscuit is required for ease of alignment during assembly Supplied with instructions. No. 0 - 45 mm x 15 mm x 4 mm Suitable for 8-12 mm boardsUse bearing B19A 9.05 mm depth No. 10 - 53 mm x 19 mm x 4 mmSuitable for 13-18 mm boardsUse bearing B16A 10.6 mm depth No. 20 - 58 mm x 23 mm x 4 mmSuitable for 19 mm + boardUse bearing B127A D1 37.2 mm Cut length 4 mm B 12.7 mm B2 16.0 mm B3 19.0 mmShank = 1/2in
The manufacturing specification for Faithfull router bit cutters ensures that they are suitable for use by all professional tradesmen, craftsmen and conscientious DIY enthusiasts. Every Faithfull router cutter tip is made from tungsten carbide, brazed onto a steel body and designed to cut a wide variety of timber and abrasive material such as MDF and plywood. With careful handling and under normal conditions, they will outlast HSS grade cutters many times. These top quality cutters will ensure an excellent finish and provide the user with long lasting and reliable service. 1/4in ShankCutting Diameter: 19.0 mm 3/4in. Cutting Length: 25 mm. Shank Diameter: 1/4in.
