Hexagonal bodied parallel pin punches with extra long pins. Used for driving out long retaining pins. The pin should be first started with a hand or taper punch to avoid damage to the point of the pin punch. Pin length: 63mm (2.1/2in).Overall length: 152mm (6in).Size. 4mm (5/32 in).
Straight edge for accurate marking out with a carpenters pencil or metal scriber. Accuracy is 0.01% of the length of the straight edge.Size: 450 x 53mm (18 x 2.08in).
Designed for maximum strength and rigidity, this clamp is hardened and extremely useful for holding work together in tapping, drilling and various machine setups. The ends of the jaws are rounded to permit clamping under shoulders or in recesses.Capacity: 70mm (2 3/4 in). Throat Depth: 45mm (1 25/32 in).
Nail punches are designed to drive nail heads below the surface of the wood. Square head provides a large striking area which also stops the punch from rolling off the bench. Knurled body with hardened, slightly cupped head.Size. 1/16 in.Length 4 in
Straight edge for accurate marking out with a carpenters pencil or metal scriber. Accuracy is 0.01% of the length of the straight edge.Size: 600 x 53mm (24 x 2.08in).
Dormer Bolt Removal Kits for the easy removal of broken bolts. Each set contains: 1 x Bolt Milling Burr (P100)1 x Bolt Centring Burr (P101)1 x Stub Drill HSS-Co (A117)1 x Screw Extractor (X106X) HOW TO USE Use a right-handed straight grinder or drill. Ensure that the bolt face mill is perpendicular to the broken bolt Step 1: Cut the broken bolt flat with P100 Step 2: Cut a centre in the rough surface to ensure the hole is drilled centrally in the bolt using P101 Step 3: Drill a hole in the bolt for the screw extractor using A117 Step 4: Remove the bolt with the screw extractor X106X1 x Dormer Bolt Removal Kit M8-M10
SB-3753N series centre punches made from vanadium steel with a hexagonal shank. Fully polished steel surfaces and a brilliant chrome finish.Size: 2mm (5/64 in).Length: 100mm (4 in)
The Facom 249.G sheathed drift punches are tough and durable. With very high tensile strength, these punches feature a head hardened to 43 HRc and a long shank hardened to 58 HRc. The handles are ergonomically shaped for comfort and shock absorption. Ideal as an aid in aligning bolt or rivet holes prior to inserting a fastener.The FCM249G4Point diameter: 3.95mm.Length: 190mm.
SB-373N series parallel pin punches made from vanadium extra steel with a hexagonal shank. Fully polished steel surfaces and a brilliant chrome finish.Length: 150mm (6 in).Size: 3mm (1/8 in).
A quick and easy way to cut clean imperial sized holes in sheet metal up to 16 gauge. The special design allows an even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches boxed singly without key, which should be ordered separately. To use these punches they require a hole to be drilled through the sheet metal (large enough to clear the heagonal Screw) then the Die and hexagonal screw are threaded through the sheet metal then onto the die nut and screw die nut. When the hexagonal screw is tightened the punch will cut cleanly and evenly through the metal.Size. 9/16 in.Key Type. 7/32 in hexagonal wrench
A quick and easy way to cut clean metric sized holes in sheet metal up to 16 gauge. The special design allows even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches are sold singly without key, which should be ordered separately. Thread the punch onto the hexagonal screw and then pass the hexagonal screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting hexagonal screw until it touches the metal sheet. Use a hexagonal key to turn the hexagonal screw. The screw will pull the punch through the metal and a hole will result. Please note these instructions apply to cutters up to 15 mm in size, for cutters 15 mm and over have a different configuration. Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.Size.28.3mm.Key Type.MB. 8mm hexagonal wrench
A quick and easy way to cut clean metric sized holes in sheet metal up to 16 gauge. The special design allows even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches are sold singly without key, which should be ordered separately. Thread the punch onto the hexagonal screw and then pass the hexagonal screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting hexagonal screw until it touches the metal sheet. Use a hexagonal key to turn the hexagonal screw. The screw will pull the punch through the metal and a hole will result. Please note these instructions apply to cutters up to 15 mm in size, for cutters 15 mm and over have a different configuration. Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.Size.24.0mm.Key Type.MB. 8mm hexagonal wrench
A quick and easy way to cut clean imperial sized holes in sheet metal up to 16 gauge. The special design allows an even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches boxed singly without key, which should be ordered separately. To use these punches they require a hole to be drilled through the sheet metal (large enough to clear the heagonal Screw) then the Die and hexagonal screw are threaded through the sheet metal then onto the die nut and screw die nut. When the hexagonal screw is tightened the punch will cut cleanly and evenly through the metal.Size. 1 5/8 in.Key Type.B. 5/16 in hexagonal wrench
Extra long pin punch. Hardened and tempered with a knurled grip. The drive pin sections are 90mm (3.1/2in) long and the diameters of the punches are slightly under the sizes listed. Length: 200mm (8in).1 x Starrett S248PC Long Pin Punch Set 5 Piece Sizes: 3mm (1/8in), 5mm (3/16in), 6mm (1/4in), 8mm (5/16in) and 9.5mm (3/8in).
Used to adjust tappets, spark plugs, distributor points, checking bearing clearances and gear play, fitting pistons, rings and pins and gauging narrow slots. Leaves are tempered steel, easily removed and replaced. Locking device on all sets.Inch Reading Gauges with Straight leaves 1/2 x 4 1/2 in No. of leaves: 13 Range: 0.0015 - 0.200 Inch (0.0015, 0.002, 0.003, 0.004, 0.006, 0.008, 0.010 to 0.040 by 0.01 in steps , 0.075, 0.100, 0.200 in).
Extra long pin punch. Hardened and tempered with a knurled grip. The drive pin sections are 90mm (3.1/2in) long and the diameters of the punches are slightly under the sizes listed. Length: 200mm (8in).Size 9.5mm (3/8 in)
Extra long pin punch. Hardened and tempered with a knurled grip. The drive pin sections are 90mm (3.1/2in) long and the diameters of the punches are slightly under the sizes listed. Length: 200mm (8in).Size 3mm (1/8 in)
The Moore & Wright Engineer's Levels have a precision ground cast base with a V-groove for location on cylindrical work. Each level is fitted with a main, cross and plumb vial and the main vial is protected by a rotating shroud. The solution in the vials maintains colour and fluidity under all workshop conditions and the main vial has a sensitivity of 1 minute.The Moore & Wright ELS Engineer's Levels have the following specification: Length: 165mm (6.5in).Width: 34mm (1.34in).Height: 46mm (1.81in).Resolution: 0.3mm per metre (0.0035in per foot).
These Dormer 2 piece sets each feature a tap and its corresponding pre-hole drill in one convenient package, helping to save time and error.The packs contain an A002 split-point jobber drill and a straight flute tap. The taps are suitable for threading up to 1.5x their diameter in most materials (ISO Standard). Two tap options are available: Second tap for through drilling, or a bottoming tap for blind holes.Specifications: Tap Type: BottomingThread Size: M5
Dormer E500 straight flute taps are the only type of taps that can be used by hand, but they may also be used in a machine if required. Extremely versatile, can tap through or blind holes in most materials. When tapping blind holes straight flute taps should be used in sets. The three taps which form a set are known by more than one name. 1. Taper or First tap2. Second or Intermediate tap3. Bottoming, third or plug tap. Metric coarse straight flute taps. Tolerance: Class 2 for 6H FitSurface treatment: BrightMaterial: HSS High Speed SteelChamfer No: 1,2 and 3, Serial no 4 and 5Flute Geometry: Straight Flutes ISO529Size: 3.0mm x 0.5 Second.
Dormer E500 straight flute taps are the only type of taps that can be used by hand, but they may also be used in a machine if required. Extremely versatile, can tap through or blind holes in most materials. When tapping blind holes straight flute taps should be used in sets. The three taps which form a set are known by more than one name. 1. Taper or First tap2. Second or Intermediate tap3. Bottoming, third or plug tap. Metric coarse straight flute taps. Tolerance: Class 2 for 6H FitSurface treatment: BrightMaterial: HSS High Speed SteelChamfer No: 1,2 and 3, Serial no 4 and 5Flute Geometry: Straight Flutes ISO529Size 14.0 x 2.0 second
