Metric 333mm lengths of high carbon bright steel, precision ground to very close tolerances; Above 25mm + - 0.025mm.Below 25mm + - 0.0127mm. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 18mm
Dormer Dienuts are used to reclaim worn or damaged threads in most materials. Metric Coarse Dienuts. Application: For reclamation of screw threads. Also available in MF, UNC, G(BSPF) thread forms. Tolerance: 6g.Chamfer Lead: Two Threads.Surface treatment: Bright.Material: HSS - High Speed Steel. BS1127:1950Size: 12mm x 1.75.
Dormer E500 straight flute taps are the only type of taps that can be used by hand, but they may also be used in a machine if required. Extremely versatile, can tap through or blind holes in most materials. When tapping blind holes straight flute taps should be used in sets. The three taps which form a set are known by more than one name. 1. Taper or First tap2. Second or Intermediate tap3. Bottoming, third or plug tap. Metric coarse straight flute taps. Tolerance: Class 2 for 6H FitSurface treatment: BrightMaterial: HSS High Speed SteelChamfer No: 1,2 and 3, Serial no 4 and 5Flute Geometry: Straight Flutes ISO529Size 4.0mm x 0.7 bottoming
The Moore & Wright Spring Dividers are manufactured from polished tool steel and the points are hardened to over 550Hv. The bow spring ensures uniform tension over working range and they are fitted with a centrally mounted adjustment screw. These Spring Dividers comply with BS3123 standards. Note: The nominal size is the distance between the centre of the roller and the working ends of the legs.The Moore & Wright 503 Spring Dividers have the following specifications: Size: 75mm (3in).
A quick and easy way to cut clean imperial sized holes in sheet metal up to 16 gauge. The special design allows an even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches boxed singly without key, which should be ordered separately. To use these punches they require a hole to be drilled through the sheet metal (large enough to clear the heagonal Screw) then the Die and hexagonal screw are threaded through the sheet metal then onto the die nut and screw die nut. When the hexagonal screw is tightened the punch will cut cleanly and evenly through the metal.Size. 5/8 in.Key Type. 7/32 in hexagonal wrench
A quick and easy way to cut clean metric sized holes in sheet metal up to 16 gauge. The special design allows even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches are sold singly without key, which should be ordered separately. Thread the punch onto the hexagonal screw and then pass the hexagonal screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting hexagonal screw until it touches the metal sheet. Use a hexagonal key to turn the hexagonal screw. The screw will pull the punch through the metal and a hole will result. Please note these instructions apply to cutters up to 15 mm in size, for cutters 15 mm and over have a different configuration. Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.Size.29.0mm.Key Type.MB. 8mm hexagonal wrench
Stanley 158501 FatMax® Interchangeable Nail Set with two nail set sizes (1/32in and 1/16in). Bi-material grip for comfort and reduced slipping. 1/4in locking system accepts standard screwdriver bits.
This hollow punch is made from carbon steel. It has a ground tapered section with a milled clearway for removing waste materials. It is intended for cutting soft materials such as leather.
Number punches are for marking metals and other solid materials. Produced from quality steel, heat treated to give maximum endurance and accuracy of impression. Set contains 0-9 with the latter inverted to double up as a 6. Packed in attractive plastic box.Size. 5mm (3/16 in).
SB-373N series parallel pin punches made from vanadium extra steel with a hexagonal shank. Fully polished steel surfaces and a brilliant chrome finish.Length: 150mm (6 in).Size: 5mm (3/16 in).
Kits comprise of a single wad punch handle onto which screws a series of nine interchangeable punches. The handles are blackened and punches heat treated and chemically blacked. The handle should be struck with a hammer or mallet onto a wooden block. The spring loaded plunger in the handle enables holes to be accurately centred and serves to eject the slug. The metric set contains: 5, 6, 8, 10, 12.5, 16, 20, 25 and 32mm sizes. The imperial set contains: 1/4, 5/16, 3/8, 7/16, 1/2, 5/8, 3/4, 7/8 and 1in sizes.Set contains: 1/4,5/16,3/8,7/16,1/2,5/8,3/4,7/8 and 1 in sizes.
These Dormer 2 piece sets each feature a tap and its corresponding pre-hole drill in one convenient package, helping to save time and error.The packs contain an A002 split-point jobber drill and a straight flute tap. The taps are suitable for threading up to 1.5x their diameter in most materials (ISO Standard). Two tap options are available: Second tap for through drilling, or a bottoming tap for blind holes.Specifications: Tap Type: BottomingThread Size: M3
Dormer E500 straight flute taps are the only type of taps that can be used by hand, but they may also be used in a machine if required. Extremely versatile, can tap through or blind holes in most materials. When tapping blind holes straight flute taps should be used in sets. The three taps which form a set are known by more than one name. 1. Taper or First tap2. Second or Intermediate tap3. Bottoming, third or plug tap. Metric coarse straight flute taps. Tolerance: Class 2 for 6H FitSurface treatment: BrightMaterial: HSS High Speed SteelChamfer No: 1,2 and 3, Serial no 4 and 5Flute Geometry: Straight Flutes ISO529Size 3.5mm x 0.6 taper
The Moore & Wright Spring Joint Internal Calipers are manufactured from polished tool steel. Their bow spring ensures uniform tension over the working range. The adjustment screw is centrally mounted. These spring joint internal calipers conform to BS3123 standards.The Moore & Wright 514R Spring Joint Internal Caliper has the following specification: Size: 100mm (4in).
Imperial 13in lengths of high carbon bright steel, precision ground to very close tolerances; Above 1 in + - 0.0005in.Below 1 in + - 0.00025in. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 5/32 in
Imperial 13in lengths of high carbon bright steel, precision ground to very close tolerances; Above 1 in + - 0.0005in.Below 1 in + - 0.00025in. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 3/8 in
This Blue Spot 6 Piece Pin Punch Set contains the following sizes:2.5 x 150mm, 3.5 x 150mm, 4.5 x 150mm, 6 x 150mm, 8 x 150mm and 10 x 150mm. The punches are manufactured from heat treated alloy tool steel and are hardened to Rockwell HRC49-53.
Recoil inserts are the quick and easy way to repair damaged threads or creating stronger original threads in alloys and composite materials in original equipment manufacture.Made from corrosion resistant stainless steel, they create stronger threads in most materials and simplify changeover from unified to metric or vice versa. Recoil thread repair kits contain a quality HSS tap, Installation tool, precision stainless steel inserts and instructions.Supplied in a sturdy container.Supplied with a tapping drill.Kit 3/8 Whit x 16 tpiLength 1 1/2 x Diameter
The Moore & Wright Spring Dividers are manufactured from polished tool steel and the points are hardened to over 550Hv. The bow spring ensures uniform tension over working range and they are fitted with a centrally mounted adjustment screw. These Spring Dividers comply with BS3123 standards. Note: The nominal size is the distance between the centre of the roller and the working ends of the legs.The Moore & Wright 504 Spring Dividers have the following specifications: Size: 100mm (4in).
The BlueSpot 3 Piece Centre Punch Set is specially designed to create an indented hole for stable drilling. Manufactured from heat-treated alloy steel for increased durability. Colour coded, knurled handles provide a secure grip. Sizes: 1/32, 1/16 and 3/32in.
Wad punches are used for cutting holes in soft materials or for producing discs from the material being cut.One piece forging with ground and polished tapered section.Size 10mm (3/8 in)
