Faithfull Centre punch with a square head which provides a larger striking area and prevents the punch rolling when laid on the bench. Carefully hardened and tempered and with a 90° ground point.Point Diameter: 2.5mm (3/32in).Length: 100mm (4in).
The Moore & Wright Firm Joint Inside Calipers are manufactured from polished tool steel and have a large headed nut and screw assembly that provides a firm and rigid friction joint, with no play. The sizes listed are the effective leg length which is measured from the joint assembly. The Firm Joint Inside Calipers are manufactured to BS3123 standards. Note: Firm joint caliper capacities are generally 1/3 greater than the effective leg length.The Moore & Wright 3306R Firm Joint Inside Caliper has the following specification: Size: 150mm (6in).
Dormer E500 straight flute taps are the only type of taps that can be used by hand, but they may also be used in a machine if required. Extremely versatile, can tap through or blind holes in most materials. When tapping blind holes straight flute taps should be used in sets. The three taps which form a set are known by more than one name. 1. Taper or First tap2. Second or Intermediate tap3. Bottoming, third or plug tap. Metric coarse straight flute taps. Tolerance: Class 2 for 6H FitSurface treatment: BrightMaterial: HSS High Speed SteelChamfer No: 1,2 and 3, Serial no 4 and 5Flute Geometry: Straight Flutes ISO529Size 3.5mm x 0.6 second
This hollow punch is made from carbon steel. It has a ground tapered section with a milled clearway for removing waste materials. It is intended for cutting soft materials such as leather.
A quick and easy way to cut clean imperial sized holes in sheet metal up to 16 gauge. The special design allows an even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches boxed singly without key, which should be ordered separately. To use these punches they require a hole to be drilled through the sheet metal (large enough to clear the heagonal Screw) then the Die and hexagonal screw are threaded through the sheet metal then onto the die nut and screw die nut. When the hexagonal screw is tightened the punch will cut cleanly and evenly through the metal.Size. 11/16 in.Key Type. 7/32 in hexagonal wrench
These Dormer 2 piece sets each feature a tap and its corresponding pre-hole drill in one convenient package, helping to save time and error.The packs contain an A002 split-point jobber drill and a straight flute tap. The taps are suitable for threading up to 1.5x their diameter in most materials (ISO Standard). Two tap options are available: Second tap for through drilling, or a bottoming tap for blind holes.Specifications: Tap Type: SecondThread Size: M12
Hardened steel punches carefully heat treated for long life. Precisely knurled body with square head which gives a good striking area and prevents the punch from rolling.Size 4mm (5/32 in).Length 100mm (4 in)
Set of 7 Power Grip Screw Extractors have reverse spiral flutes for maximum gripping power. Universal shape fits metric and fractional sizes and features a 1/4in hexagon shank suitable for use with power drills and nut drivers. Made from durable high carbon steel for longer life. Sizes: 3/16in, 1/4in, 8mm (5/16in), 3/8in, 10mm, 11mm (7/16in) and 1/2in.Drive Size: 1/4in.
The Faithfull Engineer's Set has been carefully crafted from high-quality tool steel, these squares are accurate to BS939 Grade B standard. The stock and blade are precision ground to ensure straightness and accuracy, and the spring steel blade is hardened and tempered for increased durability. Set of 4 in a wooden storage case containing 50mm, 75mm, 100mm and 150mm (2in, 3in, 4in, 6in).
Manufactured from high quality C45 carbon steel, this Faithfull tap and die set is suitable for cleaning and cutting threads in mild steel, aluminium and brass. Each set contains a tap wrench, die holder, screwdriver and a range of metric taps and dies, featuring the most commonly used European threads. The Faithfull FAITAPDSET39 39 piece metric tap & die set contains the following: 1 x Tap wrench: M3-121 x Die stock holder: 25mm (1 inch)1 x Screwdriver1 x Screwpitch1 x Tap wrench16 x Metric Taps: 3x0.5mm, 3x0.6mm, 4x0.7mm, 4x0.75mm, 5x0.8mm, 5x0.9mm, 6x0.75mm, 6x1.0mm, 7x0.75mm, 7x1.0mm, 8x1.0mm, 8x1.25mm, 10x1.25mm, 10x1.5mm, 12x1.5mm, 12x1.75mm1 x Tap: 1/8 inch NPT16 x Metric Dies (same sizes as metric taps)1 x Die: 1/8 inch NPT.
The Faithfull Spring Dividers have polished natural steel finish legs made of flat stock. They are carefully balanced, with heat treated points. A strong but flexible bow spring and centrally located adjustment screw give a smooth and precise action.Size 150mm (6 in)
Faithfull Letter and number punches are used for hand marking metals and other hard materials. They are useful for stamping personal identification or post codes on tools, cycles etc., as frequently recommended by police and insurers. The letter or number sizes as shown, relate to the height of the characters. The punches are manufactured from high quality tested carbon steel with double induction hardened heads to ensure high quality impressions. The body is hardened and the head is tempered to prevent chipping when hammered.Contents : 1, 2, 3, 4, 5, 6, 7, 8, 9, 0 (9 is achieved by reversing 6).Set supplied in plastic box.Size : 6mm (1/4 in).
Manufactured from high quality C45 carbon steel, this Faithfull tap and die set is suitable for cleaning and cutting threads in mild steel, aluminium and brass. Each set contains a tap wrench, die holder, screwdriver and a range of metric taps and dies, featuring the most commonly used European threads. The Faithfull FAITAPDSET21 21 piece metric tap & die set contains the following: 1 x Tap wrench: M3-121 x Die stock holder: 25mm (1 inch)1 x Screwdriver8 x Metric Taps: 3 x 0.5mm, 4 x 0.7mm, 5 x 0.8mm, 6 x 1.0mm, 7 x 1.0mm, 8 x 1.25mm, 10 x 1.5mm and 12 x 1.75mm.1 x Tap: 1/8 inch NPT8 x Metric Dies (same sizes as metric taps)1 x Die: 1/8 inch NPT.
Hexagonal bodied parallel pin punches with extra long pins. Used for driving out long retaining pins. The pin should be first started with a hand or taper punch to avoid damage to the point of the pin punch. Pin length: 63mm (2.1/2in).Overall length: 152mm (6in).Size. 4mm (5/32 in).
The Faithfull Engineers Square has been carefully crafted from high quality tool steel, these squares are accurate to BS939 Grade B standard. The stock and blade are precision ground to ensure straightness and accuracy, and the spring steel blade is hardened and tempered for increased durability. Size: 150mm (6in) External size: 173 x 100mmInternal size: 150 x 75mmStock thickness: 11mmBlade thickness: 1.7mm
Faithfull Long series pin punch with extended parallel shank, used for the removal of tight pin and metal dowels from mechanical fittings and machinery. Designed for heavy-duty use and made from uniformly heat treated tool steel with a round head and a knurled body for a firm grip. Pin length: 90mm (3.1/2in).Overall length: 200mm (8in).Size: 2.4mm (3/32 in)
A quick and easy way to cut clean metric sized holes in sheet metal up to 16 gauge. The special design allows even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches are sold singly without key, which should be ordered separately. Thread the punch onto the hexagonal screw and then pass the hexagonal screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting hexagonal screw until it touches the metal sheet. Use a hexagonal key to turn the hexagonal screw. The screw will pull the punch through the metal and a hole will result. Please note these instructions apply to cutters up to 15 mm in size, for cutters 15 mm and over have a different configuration. Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.Size.22.5mm.Key Type.MB. 8mm hexagonal wrench
A quick and easy way to cut clean metric sized holes in sheet metal up to 16 gauge. The special design allows even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches are sold singly without key, which should be ordered separately. Thread the punch onto the hexagonal screw and then pass the hexagonal screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting hexagonal screw until it touches the metal sheet. Use a hexagonal key to turn the hexagonal screw. The screw will pull the punch through the metal and a hole will result. Please note these instructions apply to cutters up to 15 mm in size, for cutters 15 mm and over have a different configuration. Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.Size.20.4mm.Key Type.MB. 8mm hexagonal wrench
A quick and easy way to cut clean metric sized holes in sheet metal up to 16 gauge. The special design allows even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches are sold singly without key, which should be ordered separately. Thread the punch onto the hexagonal screw and then pass the hexagonal screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting hexagonal screw until it touches the metal sheet. Use a hexagonal key to turn the hexagonal screw. The screw will pull the punch through the metal and a hole will result. Please note these instructions apply to cutters up to 15 mm in size, for cutters 15 mm and over have a different configuration. Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.Size.25.0mm.Key Type.MB. 8mm hexagonal wrench
A quick and easy way to cut clean metric sized holes in sheet metal up to 16 gauge. The special design allows even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches are sold singly without key, which should be ordered separately. Thread the punch onto the hexagonal screw and then pass the hexagonal screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting hexagonal screw until it touches the metal sheet. Use a hexagonal key to turn the hexagonal screw. The screw will pull the punch through the metal and a hole will result. Please note these instructions apply to cutters up to 15 mm in size, for cutters 15 mm and over have a different configuration. Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.Size.52.0mm.Key Type.ME. 14mm hexagonal wrench
A quick and easy way to cut clean metric sized holes in sheet metal up to 16 gauge. The special design allows even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches are sold singly without key, which should be ordered separately. Thread the punch onto the hexagonal screw and then pass the hexagonal screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting hexagonal screw until it touches the metal sheet. Use a hexagonal key to turn the hexagonal screw. The screw will pull the punch through the metal and a hole will result. Please note these instructions apply to cutters up to 15 mm in size, for cutters 15 mm and over have a different configuration. Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.Size. 50.0mm.Key Type. MC. 10mm hexagonal wrench
A quick and easy way to cut clean metric sized holes in sheet metal up to 16 gauge. The special design allows even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches are sold singly without key, which should be ordered separately. Thread the punch onto the hexagonal screw and then pass the hexagonal screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting hexagonal screw until it touches the metal sheet. Use a hexagonal key to turn the hexagonal screw. The screw will pull the punch through the metal and a hole will result. Please note these instructions apply to cutters up to 15 mm in size, for cutters 15 mm and over have a different configuration. Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.Size.40.0mm.Key Type.MC. 10mm hexagonal wrench
A quick and easy way to cut clean metric sized holes in sheet metal up to 16 gauge. The special design allows even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches are sold singly without key, which should be ordered separately. Thread the punch onto the hexagonal screw and then pass the hexagonal screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting hexagonal screw until it touches the metal sheet. Use a hexagonal key to turn the hexagonal screw. The screw will pull the punch through the metal and a hole will result. Please note these instructions apply to cutters up to 15 mm in size, for cutters 15 mm and over have a different configuration. Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.Size.60.0mm.Key Type. ME. 14mm hexagonal wrench
A quick and easy way to cut clean metric sized holes in sheet metal up to 16 gauge. The special design allows even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches are sold singly without key, which should be ordered separately. Thread the punch onto the hexagonal screw and then pass the hexagonal screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting hexagonal screw until it touches the metal sheet. Use a hexagonal key to turn the hexagonal screw. The screw will pull the punch through the metal and a hole will result. Please note these instructions apply to cutters up to 15 mm in size, for cutters 15 mm and over have a different configuration. Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.Size.18.6mm.Key Type. MB. 8mm hexagonal wrench
A quick and easy way to cut clean metric sized holes in sheet metal up to 16 gauge. The special design allows even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches are sold singly without key, which should be ordered separately. Thread the punch onto the hexagonal screw and then pass the hexagonal screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting hexagonal screw until it touches the metal sheet. Use a hexagonal key to turn the hexagonal screw. The screw will pull the punch through the metal and a hole will result. Please note these instructions apply to cutters up to 15 mm in size, for cutters 15 mm and over have a different configuration. Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.Size:17.5mm.Key Type. 6mm hexagonal wrench.
A quick and easy way to cut clean metric sized holes in sheet metal up to 16 gauge. The special design allows even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches are sold singly without key, which should be ordered separately. Thread the punch onto the hexagonal screw and then pass the hexagonal screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting hexagonal screw until it touches the metal sheet. Use a hexagonal key to turn the hexagonal screw. The screw will pull the punch through the metal and a hole will result. Please note these instructions apply to cutters up to 15 mm in size, for cutters 15 mm and over have a different configuration. Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.Size.14.0mm.Key Type. 6mm hexagonal wrench
A quick and easy way to cut clean metric sized holes in sheet metal up to 16 gauge. The special design allows even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches are sold singly without key, which should be ordered separately. Thread the punch onto the hexagonal screw and then pass the hexagonal screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting hexagonal screw until it touches the metal sheet. Use a hexagonal key to turn the hexagonal screw. The screw will pull the punch through the metal and a hole will result. Please note these instructions apply to cutters up to 15 mm in size, for cutters 15 mm and over have a different configuration. Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.Size.11.0mm.Key Type. 5mm hexagonal wrench
A quick and easy way to cut clean imperial sized holes in sheet metal up to 16 gauge. The special design allows an even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches boxed singly without key, which should be ordered separately. To use these punches they require a hole to be drilled through the sheet metal (large enough to clear the heagonal Screw) then the Die and hexagonal screw are threaded through the sheet metal then onto the die nut and screw die nut. When the hexagonal screw is tightened the punch will cut cleanly and evenly through the metal.Size.1 1/8in.Key Type.B. 5/16 in hexagonal wrench
Faithfull Centre punch with a square head which provides a larger striking area and prevents the punch rolling when laid on the bench. Carefully hardened and tempered and with a 90° ground point.Point Diameter: 5mm (3/16in).Length: 100mm (4in).
Faithfull Centre punch with a square head which provides a larger striking area and prevents the punch rolling when laid on the bench. Carefully hardened and tempered and with a 90° ground point.Point Diameter: 3mm (1/8in).Length: 100mm (4in).
Nail punches are designed to drive nail heads below the surface of the wood. Square head provides a large striking area which also stops the punch from rolling off the bench. Knurled body with hardened, slightly cupped head.Set of 4 in wallet. 1 of each 1/16in, 3/32in, 1/8in, 3/16in. Length 4in
A hexagonal bodied Rivet Snap with the working end heat-treated to ensure a long life.This tool is used for the forming of heads on solid rivets.Size 3 X 115mm (1/8 x 4 1/2 in)
Manufactured from heat-treated tool steel, this dual function tool is used firstly to set the rivet up and then to form the head.Size 3 x 115mm (1/8 x 4 3/4 in).
A hardened and tempered parallel pin punch, which is used for removing pins in parallel holes. The pin should be first started with a hand or taper punch to avoid damage to the point of the parallel punch.Size 6.4mm (1/4 in).
This hollow punch is made from carbon steel. It has a ground tapered section with a milled clearway for removing waste materials. It is intended for cutting soft materials such as leather.
