Bondloc B603 is an anaerobic formulation designed for direct use on as received parts such as those with protective films. It is an Oil tolerant retainer and is designed for direct application onto as received parts where a light oily film exists or where surrounding parts contamination is a problem in maintenance. Specifications: Resin: Mod. Methacrylate.Colour: Green.Cure speed: <15 mins @ 20°C.Viscosity: 125 cps.Gap fill: 0.1mm.Flash point: >85°C.Shelf life: 12 months @ 20°C.Specific gravity: 1.04.Max operating temp: -53°C to +150°C. Cured Performance: Full Cure Time: 24 hours.Static shear (degreased): 28 N/mm².Static shear (oiled film): 21 - 24 N/mm². Size: 50ml.
Bondloc B577 Pipe Seal is a high viscosity thixotropic gel paste which cures rapidly, sealing instantly to 10 bar through its Anaerobic cure system in contact with metals in the absence of air (oxygen). When fully cured it resists pressure up to 350 bar. B577 is not suitable for oxygen systems. Good chemical/solvent resistance to Ethanol, Motor Oil, Unleaded Petrol, Acetone and Brake Fluid. Typical applications are in sealing of all types of threaded connections against water, oil, gases and most common materials conveyed by pipes. Specification: Resin: Dimethacrylate.Colour: Yellow.Cure Speed with Activator: <10 minutes.Cure Speed without Activator: <15 mins @ 20°C.Viscosity: >50,000 cps.Gap Fill: 0.05mm to 0.4mm.Flash Point: >100°C.Shelf Life: 12 months @ 20°C.Specific Gravity: 1.09.Max. Operating Temperature: +150°C. Cured Performance: Full Cure Time: 6-12 hours.Typical Breakaway Strength: >6 to <15 N/mm (2).Prevailing Torque: >3 to < 9 N/mm (2).Static Shear Strength: >5 to <15 N/mm (2). Size: 50ml.
Bondloc B574 is an Instant Gasket material that forms in place, making almost any size and shape, replacing paper, cork etc. It eliminates relaxation and on loads loss. The assembled parts are usually suitable for immediate Low Pressure ( 6 bar) service and once cured can resist 350 Bar Pressure depending on gap size. Suitable for all formed in place applications such as gear box sealing, pump flanges, transmission assemblies, cover plates on tanks, cam shaft sealing, bearing gaps, outer housings, crank case and sump assemblies and flange pipe fittings. Specifications: Resin: Dimethacrylate.Colour: Orange paste.Cure speed with Activator: 10 mins.Cure speed without Activator: 15-30 mins.Viscosity - Brookfield Sp3 @ 20rpm: 50,000cps.Gap Fill/Max Threadform: 0.5mm/M36.Flash Point: >100°C.Shelf Life: 12 months @ 20°C.Specific Gravity: 1.10.Max operating temperature: -55°C to 150°C. Cured Performance: Full Cure Time: 24 hours @ 20°C.Breakloose Strength: 8N.m.Static Shear Strength: 10N.m. Size: 50ml.
Bondloc B572 White Pipe Seal is designed for the locking and sealing of metal pipes and fittings. The product cures when confined in the absence of air between close fitting metal surfaces and prevents loosening and leakage from shock and vibration. The thixotropic nature reduces the migration of liquid product after application to the substrate. Has a good chemical/solvent resistance to Ethanol, Motor Oil, Unleaded Petrol and Brake Fluid. B572 is unusual in that it does not fully cure until some 60 hours after application, allowing for re-alignment of elbows and joints. Replaces tapes and dopes, stops gas and fluid leaks on most metals and assists in lubricating during assembly. Will not shred or tear which would contaminate your system. Use it to seal against oils, gases, chemicals, water and steam etc. Specifications: Resin: Dimethacrylate.Colour: White paste.Cure speed with activator: Not recommended.Cure speed Without Activator: up to 60 hours.Viscosity Brookfield Sp3 @ 20rpm: 20,000cps.Gap fill / Max threadform: 0.4 mm / M36.Flash Point: >85°C.Shelf Life: 36 months @ 20°C. Specific Gravity: 1.25.Max Operating Temperature: -55°C to + 150°C. Cured Performance: Full Cure Time: 60 hours.Typical breakaway strength: 6 N.m.Typical prevailing strength: 2 N.m. Size: 50ml.
Bondloc B542 Hydraulic Seal is a thixotropic liquid which cures anaerobically to form a tough, high pressure seal on all types of threaded couplings used on low, medium and high pressure lines. Used for all types of hydraulic connections, and sealing against typical pressure line ratings. Can also be used to fit valves, threaded couplings, adaptors, quick disconnect parts, compression fittings and vibration proofing joints. Specifications: Resin: Dimethacrylate.Colour: Brown.Fixture Speed No Activator: 10 - 20 mins. Fixture Speed With Activator: <5 mins. Spindle 2 @ 2.5 rpm: 1000 to 2750 cps.Spindle 2 @ 20rpm: 400 to 800 cps.Gap fill: 0.05mm to 0.25 mm.Flash point: >100°C.Shelf life: 2 Years @ 20°C.Specific gravity: 1.06.Max operating temp: -55°C to + 150°C. Cured Performance: Full Cure Time: 12 hours.Typical breakway ISO 10964: 15 N.m.Typical prevailing ISO 10964: >8 N.m.DIN 10964 Breakloose: 24 N.m.DIN 10964 Prevailing: 15 to 35 N.m.Typical Break and Prevailing: 20N.m/15N.m.Bondloc Hydraulic Seal Pneumatic Fittings. Size: 50ml.
Bondloc Gasket Seal Type B518 is a Red, smooth, thick paste. Easily applied, cures once confined between the parts to form in place a tough, flexible gasket. Gives an instant low pressure seal. Used for fuel and water pumps, split crank cases on engines, gearbox covers, engine thermostats, air compressor end caps, engine timing cam covers onto blocks, pump couplings, fuel tanks on small implements, chain saws, lawn mowers etc. Use B518 for dressing gaskets, spacers etc. Specifications: Resin: Modified Urethane Acrylate.Colour: Red Paste.Fixture Speed No Activator: Up to 12 hours.Fixture Speed With Activator: <2 hours.Viscosity: >3,500,000 cps.Gap fill: 0.5 mm.Flash point: >100°C.Shelf life: 12 months @ 20°C.Specific gravity: 1.13.Max operating temp: -55°C to + 150°C. Cured Performance: Full Cure Time: 12 hours.Tensile strength: 8 N/mm(2).Static Shear strength: 12.5 N/mm(2). Size: 50ml.
Bondloc B480 is a black rubber toughened Cyanoacrylate that bonds metals, plastics, wood, ceramics, rubber, leather, card, glass and many other materials. Cyanoacrylate adhesives cure through reaction with moisture held on the surface to be bonded. They need close fitting joints and usually solidify in seconds which has resulted in the universal generic name of 'Superglues'. Curing is started by the film of moisture found on most surfaces which is usually slightly alkaline and it is this alkalinity which causes the polymerisation. Most grades have varying viscosities and therefore they need close fitting joints. Newer developments of gelled variants allow cure in wider gaps and application to vertical surfaces. Cyanoacrylates are suited to small plastic parts and to rubber bonding. Liquid Properties:Ester base: Ethyl cyanoacrylateAppearance: Black Opaque LiquidSpecific Gravity: 25°C 1.06 g/cm²Shelf life: 6 months unopenedViscosity @ 25°C: 350 - 450 mPasSize: 20g
Bondloc B454 is a Thixotropic Non-Drip Gel Cyanoacrylate that bonds metals, plastics, wood, ceramics, rubber, leather, card, glass and many other materials. Cyanoacrylate adhesives cure through reaction with moisture held on the surface to be bonded. They need close fitting joints and usually solidify in seconds which has resulted in the universal generic name of 'Superglues'. Curing is started by the film of moisture found on most surfaces which is usually slightly alkaline and it is this alkalinity which causes the polymerisation. Most grades have varying viscosities and therefore they need close fitting joints. Newer developments of gelled variants allow cure in wider gaps and application to vertical surfaces. Cyanoacrylates are suited to small plastic parts and to rubber bonding. Liquid Properties:Ester base: Ethyl cyanoacrylateAppearance: Clear, colourlessSpecific Gravity: 25°C 1.1 g/cm²Shelf life: 12 months unopenedViscosity @ 25°C: GelSize: 20g
Bondloc B415 is a high viscosity Cyanoacrylate that bonds metals, plastics, wood, ceramics, rubber, leather, card, glass and many other materials. Cyanoacrylate adhesives cure through reaction with moisture held on the surface to be bonded. They need close fitting joints and usually solidify in seconds which has resulted in the universal generic name of 'superglues'. Curing is started by the film of moisture found on most surfaces which is usually slightly alkaline and it is this alkalinity which causes the polymerisation. Most grades have varying viscosities and therefore they need close fitting joints. Newer developments of gelled variants allow cure in wider gaps and application to vertical surfaces. Cyanoacrylates are suited to small plastic parts and to rubber bonding. Liquid Properties: Ester base: Ethyl cyanoacrylateAppearance: Clear, colourlessSpecific Gravity: 25°C 1.06 g/cm²Shelf life: 12 months unopenedViscosity @ 25°C: 1200 - 1800 Size: 20g
Bondloc B401 is a Medium Viscosity Cyanoacrylate. It bonds metals, plastics, wood, ceramics, rubber, leather, card, glass and many other materials. Cyanoacrylate adhesives cure through reaction with moisture held on the surface to be bonded. They need close fitting joints and usually solidify in seconds which has resulted in the universal generic name of 'superglues'. Curing is started by the film of moisture found on most surfaces which is usually slightly alkaline and it is this alkalinity which causes the polymerisation. Most grades have varying viscosities and therefore they need close fitting joints. Newer developments of gelled variants allow cure in wider gaps and application to vertical surfaces. Cyanoacrylates are suited to small plastic parts and to rubber bonding. Liquid Properties: Ester base: Ethyl cyanoacrylateAppearance: Clear, colourlessSpecific Gravity: 25°C 1.06 g/cm²Shelf life: 12 months unopenedViscosity @ 25°C: 90 - 120 Size: 20g
Bondloc B3294 is a toughened structural adhesive formulated for bonding dissimilar substrates as well as unprepared metals, ceramics, wood, concrete and standard thermoset plastics. The final adhesive bond is designed to be load bearing and resistant to weathering, humidity and wide temperature variations. Outdoor weathering or solvent exposure thermoformed plastic assemblies, PVC, fibreglass, vinyls, ABS, steel aluminium, stainless steel, acrylics, phenolic, polycarbonate, styrenics, Noryl, PET, wood, concrete and ceramic magnet and speaker assembly. Specifications: Viscosity: 55,000cpsColour: Off whiteWeight: 8.44 lbs/galMixed Density: 8.28lbs/galFlash Point: 51°FMixed Viscosity: No sagging gelOpen Time: 3 minutes @ 72°F, 22°CAssembly Time: 6 minutes @ 72°F, 22°CFunctional Cure: 3/4-1 hourFull Cure: 4 hoursSolvents: NoneCoverage: (based on 25ml) 152 sq.in @ 0.010in
Bondloc B270 Studlock is a permanent green coloured general-purpose adhesive for permanent threaded assemblies. B270 locks studs up to 1in, sealing against leakage and corrosion. It is chemical-resistant, resisting fuels, lubricants and most industrial liquids and gases. It eliminates double nutting and/or welding of critical assemblies. It also permits reduced casting thickness and ultimate lightness, reduced assembly stress and eliminates cracked castings due to interference fit stresses. Specifications: Resin: DimethacrylateColour: GreenFixture Speed No Activator: 10 min.Fixture Speed With Activator: 5 min. Viscosity: 500 cpsGap fill: 0.25mmFlash Point: >100°CShelf Life: minimum 12 monthSpecific Gravity: 1.06.Max Operating Temperature: -55°C to +180°C Cured Performance: Full Cure Time: 12 hours.Cure Time with good % of final strength: 2 hoursTypical Breakaway Strength DIN : 40 Nm (25/55)Typical Prevailing Strength DIN : 55 Nm (45/70)Typical Breakaway ISO 10964: 26 Nm (16/36)Typical Prevailing ISO 10964: 36 Nm (22/50)Bondloc Studlock High Strength Threadlocker Size: 50ml.
Bondloc B270 Studlock is a permanent green coloured general-purpose adhesive for permanent threaded assemblies. B270 locks studs up to 1in, sealing against leakage and corrosion. It is chemical-resistant, resisting fuels, lubricants and most industrial liquids and gases. It eliminates double nutting and/or welding of critical assemblies. It also permits reduced casting thickness and ultimate lightness, reduced assembly stress and eliminates cracked castings due to interference fit stresses. Specifications: Resin: DimethacrylateColour: GreenFixture Speed No Activator: 10 min.Fixture Speed With Activator: 5 min. Viscosity: 500 cpsGap fill: 0.25mmFlash Point: >100°CShelf Life: minimum 12 monthSpecific Gravity: 1.06.Max Operating Temperature: -55°C to +180°C Cured Performance: Full Cure Time: 12 hours.Cure Time with good % of final strength: 2 hoursTypical Breakaway Strength DIN : 40 Nm (25/55)Typical Prevailing Strength DIN : 55 Nm (45/70)Typical Breakaway ISO 10964: 26 Nm (16/36)Typical Prevailing ISO 10964: 36 Nm (22/50)Bondloc Studlock High Strength Threadlocker Size: 10ml.
Bondloc B243 is an Anaerobic formulation designed to be used on parts in an as received condition, such as those with protective films (oils) etc. Oil tolerant B243 is designed for direct application onto as received parts where a light oily film exists or where surrounding parts contamination is a problem in maintenance. Specifications: Resin: Mod MethacrylateColour: Blue ThixotropicCure speed: <15 mins @ 20°CViscosity: 1200-1800 thixotropicGap fill: 0.1mmFlash Point: >85°CShelf life: 12 months @ 20°CSpecific gravity: 1.04Max. Operating Temperature: -53°C to + 150°C Cured Performance: Full Cure Time: 24 hoursTypical Breakaway Strength: 12 N/mm²Typical Prevailing Strength: 8-10N/mm²Bondloc Nutlock Medium Strength Threadlocker Size: 50ml.
Bondloc B243 is an Anaerobic formulation designed to be used on parts in an as received condition, such as those with protective films (oils) etc. Oil tolerant B243 is designed for direct application onto as received parts where a light oily film exists or where surrounding parts contamination is a problem in maintenance. Specifications: Resin: Mod MethacrylateColour: Blue ThixotropicCure speed: <15 mins @ 20°CViscosity: 1200-1800 thixotropicGap fill: 0.1mmFlash Point: >85°CShelf life: 12 months @ 20°CSpecific gravity: 1.04Max. Operating Temperature: -53°C to + 150°C Cured Performance: Full Cure Time: 24 hoursTypical Breakaway Strength: 12 N/mm²Typical Prevailing Strength: 8-10N/mm²Bondloc Nutlock Medium Strength Threadlocker Size: 10ml.
Bondloc B222 Screwlock is a Thixotropic anaerobic threadlocker of low strength designed for easy disassembly of treated components. B222’s Anaerobic nature allows it to cure only when confined between metal parts. Applications include all small fasteners, where vibration loosening prevention and non-leakage through threaded fastening is required. Ideal on small set screws, brass and most types of small threaded nuts, bolts, screws, hex and slot driven components including keyed fasteners etc. Specifications: Resin: DimethacrylateColour: Purple White tintCure speed with Activator: <15 mins @ 20°CCure speed without Activator: 15 minutesViscosity- Brookfield Sp3 @ 20rpm: 1200 cps (thixo), Sp3 @ 20rpm: 5000cpsGap Fill/Max Threadform: 0.5mm/M36Flash Point: >100°CShelf Life: 12 months @ 20°CSpecific Gravity: 1.06 Cured performance: Full Cure Time: 12 hours @ 20°CTypical Strength: ISO 10964: 6Nm M10’sRange of Strength: Breakaway: 4Nm up to 12Nm, Prevailing: 2Nm up to 6 NmDIN 54454 Breakloose: 10Nm max 20NmDIN 54454 Prevailing: 6Nm up to 20NmBondloc Screwlock Low Strength Threadlocker Size: 50ml.
Bondloc B222 Screwlock is a Thixotropic anaerobic threadlocker of low strength designed for easy disassembly of treated components. B222’s Anaerobic nature allows it to cure only when confined between metal parts. Applications include all small fasteners, where vibration loosening prevention and non-leakage through threaded fastening is required. Ideal on small set screws, brass and most types of small threaded nuts, bolts, screws, hex and slot driven components including keyed fasteners etc. Specifications: Resin: DimethacrylateColour: Purple White tintCure speed with Activator: <15 mins @ 20°CCure speed without Activator: 15 minutesViscosity- Brookfield Sp3 @ 20rpm: 1200 cps (thixo), Sp3 @ 20rpm: 5000cpsGap Fill/Max Threadform: 0.5mm/M36Flash Point: >100°CShelf Life: 12 months @ 20°CSpecific Gravity: 1.06 Cured performance: Full Cure Time: 12 hours @ 20°CTypical Strength: ISO 10964: 6Nm M10’sRange of Strength: Breakaway: 4Nm up to 12Nm, Prevailing: 2Nm up to 6 NmDIN 54454 Breakloose: 10Nm max 20NmDIN 54454 Prevailing: 6Nm up to 20NmBondloc Screwlock Low Strength Threadlocker Size: 10ml.
Bondloc B2060 is a 60 second, 2-part, rapid cold curing epoxy adhesive. It is suitable for bonding a wide variety of surfaces including steel, aluminium and galvanised iron. It reacts within a minute to give a tough resilient bond on a wide variety of surfaces. Specifications: Mix Ratio 1:1Work Life as a Mix: 40 - 70 secondsSize: 25ml Part 1 Physical Form: Viscous liquidChemical Type: EpoxyAppearance: ClearViscosity @ 25°C: 100 poiseSpecific Gravity: 1.17 Part 2 Physical Form: Viscous liquidChemical Type: Mercaptan and PolyamideAppearance: BlueViscosity @ 25°C: 130 PoiseSpecific Gravity: 1.14
Bondloc B2001 is a hand kneadable, specialty epoxy putty that mixes in 1 minute for permanent repairs to many substrates. Contains fading black dye that becomes grey after mixing. May be applied under water (fresh or salt). Bonds to fibreglass, metal, wood, concrete and glass. Will not yellow to UV exposure. Hardens in 10 minutes, back in service in an hour, full strength in 24 hours. Can be used for repairing tanks and drums, patching holes in pipes, stopping leaks and repairing porosity holes in castings. Specification: Typical Properties: 7 days cured at 24°CColour: Black, changes to grey after mixingViscosity: putty/hand kneadablePot Life @24°C: 20 minutesComprehensive Strength: 83 N/mm2Adhesive Tensile Shear: 5 N/mm2Cured Hardness Shore: D 75Dielectric Strength: volts/mil 300Solids: 100%Temperature Resistance: Wet: 49°C, Dry: 121°CSize: 50g
Bakers Fluid No.3 is a specially formulated liquid flux ideal for soldering and tinning of copper and tinned materials.Easy to apply.Fast acting and economical in use, ensuring sound strong joints.No.3.Size 125ml.
Bahco 2681 Riveter is a swivel head rivet tool, the head swivels 360° to rivet at any angle. Will fasten metal, leather, canvas, and vinyl using 2.4, 3.2, 4.0 or 4.8mm rivets. With 4 interchangeable nosepieces which can be stored in the handle. Length: 285mm. Weight: 740g.
The BlueSpot Bungee Cordshave a heavy-duty elastic design provides constant tension and a firm hold. Offering quick, convenient load binding with non-marring high strength hooks to eliminate knots. 12mm (1/2in) diameter provides maximum holding power and is ideal for tarpaulins, cars, trucks, trailers, bikes and motorcycles.These BlueSpot Tools Bungee Cords have the following specification: Size: 60cm (24in).Quantity: 6 Piece.
The BlueSpot Tools Snap Clip Bungee Cords are designed to provide quick convenient load binding for use around the home and workplace. The 10mm diameter heavy-duty elastic cord provides excellent holding power and constant tension. The two high strength spring-loaded snap clips allow for safe and secure load binding.The BlueSpot Tools Snap Clip Bungee Cord has the following specification: Length: 120cm.Maximum Stretch: 180cm.
The BlueSpot Bungee Cordshave a heavy-duty elastic design provides constant tension and a firm hold. Offering quick, convenient load binding with non-marring high strength hooks to eliminate knots. 12mm (1/2in) diameter provides maximum holding power and is ideal for tarpaulins, cars, trucks, trailers, bikes and motorcycles.These BlueSpot Tools Bungee Cords have the following specification: Size: 120cm (48in).Quantity: 2 Piece.
The BlueSpot Tools Snap Clip Bungee Cords are designed to provide quick convenient load binding for use around the home and workplace. The 10mm diameter heavy-duty elastic cord provides excellent holding power and constant tension. The two high strength spring-loaded snap clips allow for safe and secure load binding.The BlueSpot Tools Snap Clip Bungee Cord has the following specification: Length: 90cm.Maximum Stretch: 135cm.
The BlueSpot Tools Snap Clip Bungee Cords are designed to provide quick convenient load binding for use around the home and workplace. The 10mm diameter heavy-duty elastic cord provides excellent holding power and constant tension. The two high strength spring-loaded snap clips allow for safe and secure load binding.The BlueSpot Tools Snap Clip Bungee Cord has the following specification: Length: 60cm.Maximum Stretch: 90cm.
The BlueSpot Bungee Cordshave a heavy-duty elastic design provides constant tension and a firm hold. Offering quick, convenient load binding with non-marring high strength hooks to eliminate knots. 12mm (1/2in) diameter provides maximum holding power and is ideal for tarpaulins, cars, trucks, trailers, bikes and motorcycles.These BlueSpot Tools Bungee Cords have the following specification: Size: 90cm (36in).Quantity: 2 Piece.
The BlueSpot Bungee Cordshave a heavy-duty elastic design provides constant tension and a firm hold. Offering quick, convenient load binding with non-marring high strength hooks to eliminate knots. 12mm (1/2in) diameter provides maximum holding power and is ideal for tarpaulins, cars, trucks, trailers, bikes and motorcycles.These BlueSpot Tools Bungee Cords have the following specification: Size: 60cm (24in).Quantity: 2 Piece.
The BlueSpot ratchet cargo strap has a ratchet action which quickly tightens belt to the load.45412: 25ft x 2in strap, 2 x J hooks.Rated loading capacity: 105kgMaximum loading capacity: 210kg.
The BlueSpot Ratchet Tie-Down Straps are designed for quick and easy securing and transporting of cargo. They are ideal for cars, trucks, boats, bikes and trailers. They feature a quick thumb release mechanism for easy adjustment and removal of strap. With vinyl coated S hooks, metal buckle and wide nylon webbing that provides a secure hold without scratching. Specification Length: 4.5m.Width: 25mm.Load Capacity: 225kg.Breaking Strength: 450kg.
The BlueSpot S Hook Cam Buckle is manufactured from polyester webbing with stitched reinforcement for increased durability. Fitted with plastic coated, steel S hooks for increased corrosion protection. The automatic locking cam has a quick-release function for quick and easy use and the polyester webbing is resistant to cutting and friction abrasion. The cam buckle is ideal for the securing of large, bulky or awkwardly shaped loads during transportation. Specification: Working Capacity: 250kgBreaking Capacity: 500kgLength: 2mWidth: 25mm
