Bostik Blu Tack is a permanently plastic, reusable adhesive supplied in the form of rectangular slabs between sheets of release paper. Packed in individual wallets, Blu Tack is both clean and economical in use. Clean, safe and easy-to-use. Provides an ideal alternative to drawing pins and sticky tape. It has hundreds of uses, including holding up posters, cards, children's paintings and party decorations without the need for drawing pins or sticky tape. It can even be used to clean fluff from fabric and dirt from typewriters, or it can be rolled and manipulated to make 3 dimensional artistic models.1 x Bostik Blu Tack Economy Pack
Bostik Blu Tack is a permanently plastic, reusable adhesive supplied in the form of rectangular slabs between sheets of release paper. Packed in individual wallets, Blu Tack is both clean and economical in use. Clean, safe and easy-to-use. Provides an ideal alternative to drawing pins and sticky tape. It has hundreds of uses, including holding up posters, cards, children's paintings and party decorations without the need for drawing pins or sticky tape. It can even be used to clean fluff from fabric and dirt from typewriters, or it can be rolled and manipulated to make 3 dimensional artistic models.1 x Bostik Blu Tack Handy Pack
Bostik Super Glu is effective on a large range of materials and surfaces, including china, metals, rubber, hard plastic, laminate and much more. It bonds in seconds without the need for heat or hardener and provides very strong bonds of high tensile strength. Super Glu Non-Drip Gel is supplied in a 3g tube with a fine nozzle for precise application. Its non-drip gel formula is ideal for porous surfaces.
Bostik Super Glu is effective on a large range of materials and surfaces, including china, metals, rubber, hard plastic, laminate and much more. It bonds in seconds without the need for heat or hardener and provides very strong bonds of high-tensile strength. Super Glu Easy Flow is a thin liquid glue which gives greater surface cover. It is supplied in a 5g bottle.
Bostik Super Glu is effective on a large range of materials and surfaces, including china, metals, rubber, hard plastic, laminate and much more. It bonds in seconds without the need for heat or hardener and provides very strong bonds of high tensile strength. Super Glu Liquid is supplied in a 3g tube.
Bostik Fast Tak is a strong aerosol adhesive that allows for repositioning. Clear, fast setting, non-staining adhesive for paper. Convenient spray application for larger areas. Ideal for household repairs, craft and much more.1 x Bostik Fast Tak Contact Adhesive Spray 500ml
Bostik Soft Plastic Clear Adhesive ia a strong, water-resistant clear adhesive, suitable for most soft plastics. Extra strong bond, supplied with PVC repair patch. Type: Soft plastic.Size. 20ml.
BOSTIK - CONTACT ADHESIVE Extra Strong Contact Adhesive. Water-Resistant. Dries in minutes - immediate strength on contact. Ideal for DIY and household repairs. Ideal for sticking rubber, leather, wood and much more. Type. Contact.Size. 50ml.
Bostik all purpose adhesive is a fast drying clear strong adhesive that is ideal for household repairs, DIY tasks, craft and hobby and much more.Size 50ml Tube.
Bostik all purpose adhesive is a fast drying clear strong adhesive that is ideal for household repairs, DIY tasks, craft and hobby and much more.Size 20ml Tube
Bostik All-Purpose Glue Sticks are clean and easy-to-use, giving a strong secure bond. They are extremely economical, with no waste. Water-resistant, and contain no hazardous solvents. NOTE. For use with the Standard Bostik hot melt glue gun only. Length/Diameter: 300mm x 11mm. Weight of Pack: 5Kg. (Approx 150 sticks)
Bostik All-Purpose Glue Sticks are clean and easy-to-use, giving a strong secure bond. They are extremely economical, with no waste. Water resistant, and contain no hazardous solvents. Length/Diameter: 100mm x 7mm. Approx 240 per pack.
Powerslam staples available in packs of 5,000, for use with the Powerslam Hand Tacker (BOSPC2K).Crown (mm) 10.0 Length 12 SKU STCR501912E Finish GALV Point CP Description STCR5019 STAPLE 12MM GALV 5M Qty per box 5000
Powerslam staples available in packs of 5,000, for use with the Powerslam Hand Tacker (BOSPC2K).Crown (mm) 10.0 Length 10 SKU STCR501910E Finish GALV Point CP Description STCR5019 STAPLE10MM GALV 5M Qty per box 5000
Powerslam staples available in packs of 5,000, for use with the Powerslam Hand Tacker (BOSPC2K).Crown (mm) 10.0 Length 8 SKU STCR501908E Finish GALV Point CP Description STCR5019 STAPLE 8MM GALV 5M Qty per box 5000
Powerslam staples available in packs of 5,000, for use with the Powerslam Hand Tacker (BOSPC2K).Crown (mm) 10.0 Length 6 SKU STCR501906E Finish GALV Point CP Description STCR5019 STAPLE 6MM GALV 5M Qty per box 5000
Bondloc B641 is a single part anaerobic securing compound, designed for fitting cylindrical metal assemblies and cures when confined between the parts. It will secure all types and sizes of bearings, shafts and cylindrical parts which will require disassembly in the future. It is medium strength and is colour-coded yellow for job identification. Specifications: Resin: Mod. Dimethacrylate.Colour: Yellow. Fixture Speed No Activator: 10-15 mins.Fixture Speed With Activator: <5 mins. Viscosity: 400-800 cps.Gap fill: 0.2 mm. Flash Point: >100°C. Shelf Life: 12 month min.Specific Gravity: 1.06.Max Operating Temperature: -55°C to + 150°C. Cured Performance: Full Cure Time: 12 hours.Static shear strength: 12N/mm².ISO 10123 pin/collars range: 1-16 N/mm(²).Bondloc Bearing Fit Retaining Compound. Size: 50ml.
Bondloc B641 is a single part anaerobic securing compound, designed for fitting cylindrical metal assemblies and cures when confined between the parts. It will secure all types and sizes of bearings, shafts and cylindrical parts which will require disassembly in the future. It is medium strength and is colour-coded yellow for job identification. Specifications: Resin: Mod. Dimethacrylate.Colour: Yellow. Fixture Speed No Activator: 10-15 mins.Fixture Speed With Activator: <5 mins. Viscosity: 400-800 cps.Gap fill: 0.2 mm. Flash Point: >100°C. Shelf Life: 12 month min.Specific Gravity: 1.06.Max Operating Temperature: -55°C to + 150°C. Cured Performance: Full Cure Time: 12 hours.Static shear strength: 12N/mm².ISO 10123 pin/collars range: 1-16 N/mm(²).Bondloc Bearing Fit Retaining Compound. Size: 10ml.
Bondloc B638 Retainer is designed to give high strength retention under cyclic loading. It can retain its full strength and not suffer fatigue under load stress. It is a cylindrical parts supplement, suited to structural components such as cylindrical parts under dynamic load, keys, splines, even structural tubing with close tolerance fit. Specifications: Resin: Urethane Acrylate.Colour: Green.Fixture Speed No Activator: 5 mins.Fixture Speed With Activator: <5 mins.Viscosity: 2500 cps.Gap fill: 0.2mm.Flash Point: >85°C.Shelf Life: 12 months min.Specific Gravity: 1.08.Max Operating Temperature: -55°C to + 150°C. Cured Performance: Full Cure Time: 24 hours.Static shear strength: 30 N/mm².Bondloc High Strength Retaining Compound. Size: 50ml.
Bondloc B638 Retainer is designed to give high strength retention under cyclic loading. It can retain its full strength and not suffer fatigue under load stress. It is a cylindrical parts supplement, suited to structural components such as cylindrical parts under dynamic load, keys, splines, even structural tubing with close tolerance fit. Specifications: Resin: Urethane Acrylate.Colour: Green.Fixture Speed No Activator: 5 mins.Fixture Speed With Activator: <5 mins.Viscosity: 2500 cps.Gap fill: 0.2mm.Flash Point: >85°C.Shelf Life: 12 months min.Specific Gravity: 1.08.Max Operating Temperature: -55°C to + 150°C. Cured Performance: Full Cure Time: 24 hours.Static shear strength: 30 N/mm².Bondloc high strength retaining Compound. Size: 10ml.
Bondloc B603 is an anaerobic formulation designed for direct use on as received parts such as those with protective films. It is an Oil tolerant retainer and is designed for direct application onto as received parts where a light oily film exists or where surrounding parts contamination is a problem in maintenance. Specifications: Resin: Mod. Methacrylate.Colour: Green.Cure speed: <15 mins @ 20°C.Viscosity: 125 cps.Gap fill: 0.1mm.Flash point: >85°C.Shelf life: 12 months @ 20°C.Specific gravity: 1.04.Max operating temp: -53°C to +150°C. Cured Performance: Full Cure Time: 24 hours.Static shear (degreased): 28 N/mm².Static shear (oiled film): 21 - 24 N/mm². Size: 50ml.
Bondloc B577 Pipe Seal is a high viscosity thixotropic gel paste which cures rapidly, sealing instantly to 10 bar through its Anaerobic cure system in contact with metals in the absence of air (oxygen). When fully cured it resists pressure up to 350 bar. B577 is not suitable for oxygen systems. Good chemical/solvent resistance to Ethanol, Motor Oil, Unleaded Petrol, Acetone and Brake Fluid. Typical applications are in sealing of all types of threaded connections against water, oil, gases and most common materials conveyed by pipes. Specification: Resin: Dimethacrylate.Colour: Yellow.Cure Speed with Activator: <10 minutes.Cure Speed without Activator: <15 mins @ 20°C.Viscosity: >50,000 cps.Gap Fill: 0.05mm to 0.4mm.Flash Point: >100°C.Shelf Life: 12 months @ 20°C.Specific Gravity: 1.09.Max. Operating Temperature: +150°C. Cured Performance: Full Cure Time: 6-12 hours.Typical Breakaway Strength: >6 to <15 N/mm (2).Prevailing Torque: >3 to < 9 N/mm (2).Static Shear Strength: >5 to <15 N/mm (2). Size: 50ml.
Bondloc B574 is an Instant Gasket material that forms in place, making almost any size and shape, replacing paper, cork etc. It eliminates relaxation and on loads loss. The assembled parts are usually suitable for immediate Low Pressure ( 6 bar) service and once cured can resist 350 Bar Pressure depending on gap size. Suitable for all formed in place applications such as gear box sealing, pump flanges, transmission assemblies, cover plates on tanks, cam shaft sealing, bearing gaps, outer housings, crank case and sump assemblies and flange pipe fittings. Specifications: Resin: Dimethacrylate.Colour: Orange paste.Cure speed with Activator: 10 mins.Cure speed without Activator: 15-30 mins.Viscosity - Brookfield Sp3 @ 20rpm: 50,000cps.Gap Fill/Max Threadform: 0.5mm/M36.Flash Point: >100°C.Shelf Life: 12 months @ 20°C.Specific Gravity: 1.10.Max operating temperature: -55°C to 150°C. Cured Performance: Full Cure Time: 24 hours @ 20°C.Breakloose Strength: 8N.m.Static Shear Strength: 10N.m. Size: 50ml.
Bondloc B572 White Pipe Seal is designed for the locking and sealing of metal pipes and fittings. The product cures when confined in the absence of air between close fitting metal surfaces and prevents loosening and leakage from shock and vibration. The thixotropic nature reduces the migration of liquid product after application to the substrate. Has a good chemical/solvent resistance to Ethanol, Motor Oil, Unleaded Petrol and Brake Fluid. B572 is unusual in that it does not fully cure until some 60 hours after application, allowing for re-alignment of elbows and joints. Replaces tapes and dopes, stops gas and fluid leaks on most metals and assists in lubricating during assembly. Will not shred or tear which would contaminate your system. Use it to seal against oils, gases, chemicals, water and steam etc. Specifications: Resin: Dimethacrylate.Colour: White paste.Cure speed with activator: Not recommended.Cure speed Without Activator: up to 60 hours.Viscosity Brookfield Sp3 @ 20rpm: 20,000cps.Gap fill / Max threadform: 0.4 mm / M36.Flash Point: >85°C.Shelf Life: 36 months @ 20°C. Specific Gravity: 1.25.Max Operating Temperature: -55°C to + 150°C. Cured Performance: Full Cure Time: 60 hours.Typical breakaway strength: 6 N.m.Typical prevailing strength: 2 N.m. Size: 50ml.
Bondloc B542 Hydraulic Seal is a thixotropic liquid which cures anaerobically to form a tough, high pressure seal on all types of threaded couplings used on low, medium and high pressure lines. Used for all types of hydraulic connections, and sealing against typical pressure line ratings. Can also be used to fit valves, threaded couplings, adaptors, quick disconnect parts, compression fittings and vibration proofing joints. Specifications: Resin: Dimethacrylate.Colour: Brown.Fixture Speed No Activator: 10 - 20 mins. Fixture Speed With Activator: <5 mins. Spindle 2 @ 2.5 rpm: 1000 to 2750 cps.Spindle 2 @ 20rpm: 400 to 800 cps.Gap fill: 0.05mm to 0.25 mm.Flash point: >100°C.Shelf life: 2 Years @ 20°C.Specific gravity: 1.06.Max operating temp: -55°C to + 150°C. Cured Performance: Full Cure Time: 12 hours.Typical breakway ISO 10964: 15 N.m.Typical prevailing ISO 10964: >8 N.m.DIN 10964 Breakloose: 24 N.m.DIN 10964 Prevailing: 15 to 35 N.m.Typical Break and Prevailing: 20N.m/15N.m.Bondloc Hydraulic Seal Pneumatic Fittings. Size: 50ml.
Bondloc Gasket Seal Type B518 is a Red, smooth, thick paste. Easily applied, cures once confined between the parts to form in place a tough, flexible gasket. Gives an instant low pressure seal. Used for fuel and water pumps, split crank cases on engines, gearbox covers, engine thermostats, air compressor end caps, engine timing cam covers onto blocks, pump couplings, fuel tanks on small implements, chain saws, lawn mowers etc. Use B518 for dressing gaskets, spacers etc. Specifications: Resin: Modified Urethane Acrylate.Colour: Red Paste.Fixture Speed No Activator: Up to 12 hours.Fixture Speed With Activator: <2 hours.Viscosity: >3,500,000 cps.Gap fill: 0.5 mm.Flash point: >100°C.Shelf life: 12 months @ 20°C.Specific gravity: 1.13.Max operating temp: -55°C to + 150°C. Cured Performance: Full Cure Time: 12 hours.Tensile strength: 8 N/mm(2).Static Shear strength: 12.5 N/mm(2). Size: 50ml.
Bondloc B480 is a black rubber toughened Cyanoacrylate that bonds metals, plastics, wood, ceramics, rubber, leather, card, glass and many other materials. Cyanoacrylate adhesives cure through reaction with moisture held on the surface to be bonded. They need close fitting joints and usually solidify in seconds which has resulted in the universal generic name of 'Superglues'. Curing is started by the film of moisture found on most surfaces which is usually slightly alkaline and it is this alkalinity which causes the polymerisation. Most grades have varying viscosities and therefore they need close fitting joints. Newer developments of gelled variants allow cure in wider gaps and application to vertical surfaces. Cyanoacrylates are suited to small plastic parts and to rubber bonding. Liquid Properties:Ester base: Ethyl cyanoacrylateAppearance: Black Opaque LiquidSpecific Gravity: 25°C 1.06 g/cm²Shelf life: 6 months unopenedViscosity @ 25°C: 350 - 450 mPasSize: 20g
Bondloc B454 is a Thixotropic Non-Drip Gel Cyanoacrylate that bonds metals, plastics, wood, ceramics, rubber, leather, card, glass and many other materials. Cyanoacrylate adhesives cure through reaction with moisture held on the surface to be bonded. They need close fitting joints and usually solidify in seconds which has resulted in the universal generic name of 'Superglues'. Curing is started by the film of moisture found on most surfaces which is usually slightly alkaline and it is this alkalinity which causes the polymerisation. Most grades have varying viscosities and therefore they need close fitting joints. Newer developments of gelled variants allow cure in wider gaps and application to vertical surfaces. Cyanoacrylates are suited to small plastic parts and to rubber bonding. Liquid Properties:Ester base: Ethyl cyanoacrylateAppearance: Clear, colourlessSpecific Gravity: 25°C 1.1 g/cm²Shelf life: 12 months unopenedViscosity @ 25°C: GelSize: 20g
Bondloc B415 is a high viscosity Cyanoacrylate that bonds metals, plastics, wood, ceramics, rubber, leather, card, glass and many other materials. Cyanoacrylate adhesives cure through reaction with moisture held on the surface to be bonded. They need close fitting joints and usually solidify in seconds which has resulted in the universal generic name of 'superglues'. Curing is started by the film of moisture found on most surfaces which is usually slightly alkaline and it is this alkalinity which causes the polymerisation. Most grades have varying viscosities and therefore they need close fitting joints. Newer developments of gelled variants allow cure in wider gaps and application to vertical surfaces. Cyanoacrylates are suited to small plastic parts and to rubber bonding. Liquid Properties: Ester base: Ethyl cyanoacrylateAppearance: Clear, colourlessSpecific Gravity: 25°C 1.06 g/cm²Shelf life: 12 months unopenedViscosity @ 25°C: 1200 - 1800 Size: 20g
Bondloc B401 is a Medium Viscosity Cyanoacrylate. It bonds metals, plastics, wood, ceramics, rubber, leather, card, glass and many other materials. Cyanoacrylate adhesives cure through reaction with moisture held on the surface to be bonded. They need close fitting joints and usually solidify in seconds which has resulted in the universal generic name of 'superglues'. Curing is started by the film of moisture found on most surfaces which is usually slightly alkaline and it is this alkalinity which causes the polymerisation. Most grades have varying viscosities and therefore they need close fitting joints. Newer developments of gelled variants allow cure in wider gaps and application to vertical surfaces. Cyanoacrylates are suited to small plastic parts and to rubber bonding. Liquid Properties: Ester base: Ethyl cyanoacrylateAppearance: Clear, colourlessSpecific Gravity: 25°C 1.06 g/cm²Shelf life: 12 months unopenedViscosity @ 25°C: 90 - 120 Size: 20g
Bondloc B3294 is a toughened structural adhesive formulated for bonding dissimilar substrates as well as unprepared metals, ceramics, wood, concrete and standard thermoset plastics. The final adhesive bond is designed to be load bearing and resistant to weathering, humidity and wide temperature variations. Outdoor weathering or solvent exposure thermoformed plastic assemblies, PVC, fibreglass, vinyls, ABS, steel aluminium, stainless steel, acrylics, phenolic, polycarbonate, styrenics, Noryl, PET, wood, concrete and ceramic magnet and speaker assembly. Specifications: Viscosity: 55,000cpsColour: Off whiteWeight: 8.44 lbs/galMixed Density: 8.28lbs/galFlash Point: 51°FMixed Viscosity: No sagging gelOpen Time: 3 minutes @ 72°F, 22°CAssembly Time: 6 minutes @ 72°F, 22°CFunctional Cure: 3/4-1 hourFull Cure: 4 hoursSolvents: NoneCoverage: (based on 25ml) 152 sq.in @ 0.010in
Bondloc B270 Studlock is a permanent green coloured general-purpose adhesive for permanent threaded assemblies. B270 locks studs up to 1in, sealing against leakage and corrosion. It is chemical-resistant, resisting fuels, lubricants and most industrial liquids and gases. It eliminates double nutting and/or welding of critical assemblies. It also permits reduced casting thickness and ultimate lightness, reduced assembly stress and eliminates cracked castings due to interference fit stresses. Specifications: Resin: DimethacrylateColour: GreenFixture Speed No Activator: 10 min.Fixture Speed With Activator: 5 min. Viscosity: 500 cpsGap fill: 0.25mmFlash Point: >100°CShelf Life: minimum 12 monthSpecific Gravity: 1.06.Max Operating Temperature: -55°C to +180°C Cured Performance: Full Cure Time: 12 hours.Cure Time with good % of final strength: 2 hoursTypical Breakaway Strength DIN : 40 Nm (25/55)Typical Prevailing Strength DIN : 55 Nm (45/70)Typical Breakaway ISO 10964: 26 Nm (16/36)Typical Prevailing ISO 10964: 36 Nm (22/50)Bondloc Studlock High Strength Threadlocker Size: 50ml.
Bondloc B270 Studlock is a permanent green coloured general-purpose adhesive for permanent threaded assemblies. B270 locks studs up to 1in, sealing against leakage and corrosion. It is chemical-resistant, resisting fuels, lubricants and most industrial liquids and gases. It eliminates double nutting and/or welding of critical assemblies. It also permits reduced casting thickness and ultimate lightness, reduced assembly stress and eliminates cracked castings due to interference fit stresses. Specifications: Resin: DimethacrylateColour: GreenFixture Speed No Activator: 10 min.Fixture Speed With Activator: 5 min. Viscosity: 500 cpsGap fill: 0.25mmFlash Point: >100°CShelf Life: minimum 12 monthSpecific Gravity: 1.06.Max Operating Temperature: -55°C to +180°C Cured Performance: Full Cure Time: 12 hours.Cure Time with good % of final strength: 2 hoursTypical Breakaway Strength DIN : 40 Nm (25/55)Typical Prevailing Strength DIN : 55 Nm (45/70)Typical Breakaway ISO 10964: 26 Nm (16/36)Typical Prevailing ISO 10964: 36 Nm (22/50)Bondloc Studlock High Strength Threadlocker Size: 10ml.
Bondloc B243 is an Anaerobic formulation designed to be used on parts in an as received condition, such as those with protective films (oils) etc. Oil tolerant B243 is designed for direct application onto as received parts where a light oily film exists or where surrounding parts contamination is a problem in maintenance. Specifications: Resin: Mod MethacrylateColour: Blue ThixotropicCure speed: <15 mins @ 20°CViscosity: 1200-1800 thixotropicGap fill: 0.1mmFlash Point: >85°CShelf life: 12 months @ 20°CSpecific gravity: 1.04Max. Operating Temperature: -53°C to + 150°C Cured Performance: Full Cure Time: 24 hoursTypical Breakaway Strength: 12 N/mm²Typical Prevailing Strength: 8-10N/mm²Bondloc Nutlock Medium Strength Threadlocker Size: 50ml.
