Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments. 28° Collation Angle Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out. (Remember only tools fitted with sequential trip should be used when working up a ladder). Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them. Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.Gauge/Diameter (mm) 3.1 Length 9028 Collation Angle SKU S31090G8 Profile PLAIN Finish G8 Description STICK NAIL 3.10-90 PLAIN GAL8 2M Qty per box 2000 Will also fit the N80SB, FW28WW-E, N100S
Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments. 28° Collation Angle Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out. (Remember only tools fitted with sequential trip should be used when working up a ladder). Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them. Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.Gauge/Diameter (mm) 2.8 Length 7528 Collation Angle SKU S28075 Profile PLAIN Finish BRIGHT Description STICK NAIL 2.80-75 PLAIN 2M Qty per box 2000 Will also fit the N80SB, FW28WW-E, N100S
These plug cutters are designed to exactly fit the counterbored holes produced by group 62 and 63 Trend cutters. Recommended speed - 1,000-20,000 /min.TCT for use with drilling machines or routers.H.S.S.1/4in Shank.C = 9.5 mmD = 16 mmPlug Body Diameter. 16 mm
These plug cutters are designed to exactly fit the counterbored holes produced by group 62 and 63 Trend cutters. Recommended speed - 1,000-20,000 /min.H.S.S.1/4in Shank.C = 16 mmD = 12 mmPlug Body Diameter. 22 mm
Flexovit 1/2 perforated sanding sheets are tough and durable sanding sheets, with heavy paper backing for longer life, and are ideal for general purpose sanding and stock removal. The tough and sharp High Performance Aluminium Oxide combined with a heavy paper backing makes this product extremely durable and long lasting. Suitable for use on wood, paint and metal. Size: 10 Hole Configuration, 115 x 280mm.Packed in 10s
Flexovit 1/2 perforated sanding sheets are tough and durable sanding sheets, with heavy paper backing for longer life, and are ideal for general purpose sanding and stock removal. The tough and sharp High Performance Aluminium Oxide combined with a heavy paper backing makes this product extremely durable and long lasting. Suitable for use on wood, paint and metal. Size: 10 Hole Configuration, 115 x 280mm.Packed in 10s
The Faithfull Pre-cut aluminium oxide sheets manufactured from aluminium oxide on a flexible E-weight paper backing, these sheets are cut to the correct size and shape. Suitable for use with third sheet orbital sanders.Grit: 80 (Medium). Pack quantity: 10.
Faithfull Quarter e-weight aluminium oxide paper sheets for sanding wood, plastics and fillers. They can be used with most orbital palm sanders. Size: 115 x 140mm.Fine.Pack of 5 Sheets.
Chamfer V grooving cutters are used for bevelling, chamfering and producing mortar grooves. Due to design, an approx. 1.0 mm flat will be found on the nose. Typical trade applications include sign making, freehand engraving, cabinet making and decorative joinery.T.C.T.1/3in Shank.Diameter. 19mmC1 = 9.2mm.C2 = 13.0mm.
Chamfer V grooving cutters are used for bevelling, chamfering and producing mortar grooves. Due to design, an approx. 1.0 mm flat will be found on the nose. Typical trade applications include sign making, freehand engraving, cabinet making and decorative joinery.Tooling : T.C.T.1/4in Shank.A = 60°.D = 12.7mm.C1 = 10.3mm.C2 = 11.9mm.
These cutters are used extensively for routing edge moulds, face grooves, columns, fluting, water slots, engraving and panel moulds in products such as desk tops, fire surrounds, draining boards and picture frames. These cutters are suitable for use on all natural timbers and man-made boards.Tooling : T.C.T.1/4in Shank.R = 3 mmD = 6 mmC = 15 mm
These cutters are used extensively for routing edge moulds, face grooves, columns, fluting, water slots, engraving and panel moulds in products such as desk tops, fire surrounds, draining boards and picture frames. These cutters are suitable for use on all natural timbers and man-made boards.Tooling : T.C.T.1/4in Shank.R = 10 mmD = 20 mmC = 18 mm
These cutters are used extensively for routing edge moulds, face grooves, columns, fluting, water slots, engraving and panel moulds in products such as desk tops, fire surrounds, draining boards and picture frames. These cutters are suitable for use on all natural timbers and man-made boards.TC.1/2in ShankR = 12.7 mmD = 25.4 mmC = 15.9 mm
Bostitch Stanox staples are also known as 84 series. For use with TU-216-84-E or other tools using 84 gauge.Wire gauge 0.5 mm x 1mm, 12.3 mm crown staple with 12 mm leg length.
Bostitch Stanox staples are also known as 84 series. For use with TU-216-84-E or other tools using 84 gauge.Wire gauge 0.5 mm x 1mm, 12.3 mm crown staple with 10 mm leg length.
These cutters are suitable for grooving, rebating, morticing and drilling. The single flute cutters offer fast free cutting. If you require a cleaner cut please use two flute cutters. The depth of cut on cutters of 2.0mm diameter and below should be a maximum of 1.0mm per pass. Small diameters in Tungsten Carbide must be handled with care to avoid breakage and very shallow passes must be made. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods Single flute cutters must not be used in eccentric chucks.Shank: 1/4in.Dimensions:Shank: 1/4inCutting Diameter (D): 1.5mmCutting Length (C): 6.0mm
The DEWALT 2X Life Metal Reciprocating Blades for cutting a wide range of metals: Rebar, Angle Iron, Black Pipe, Copper, Duct Work, Conduit, Sheet Metal, Thin Gauge Steel and Pipe. They have superior HSS (high speed steel) teeth with added Cobalt for hardness and strength, with greater flex for excellent cutting performance and long life even in the most demanding applications. The 14/18 tooth configuration reduces tooth breakage in hard metals providing excellent cutting performance and long life in the toughest applications. They have an optimised blade design offering increased height and thickness for sturdiness, strength and extreme durability. The ToughCoat hardened coating lowers surface friction and reduces heat build up to promote long blade life. They have an aggressive shank angle that increases tooth engagement in all materials and extends blade life. Size: 203mm. Pitch: 1.8-1.4mm.TPI: 14/18. Pack of 5.
LENOX® Demolition Bi-Metal-Reciprocating Saw Blades use POWER BLAST TECHNOLOGY™ to increase blade life. High-speed blasting along the cutting edge strengthens the blade to reduce breaks and increase durability. The blade design provides maximum durability. The taller and thicker blade profile prevents bending during cutting and provides maximum control in the toughest demolition applications.Pack of 2 LENOX® 20597-960R Demolition Reciprocating Saw Blades 225mm 10 TPI Ideal for demolition work, cutting in thick metal and fire/rescue applications.
High-performance, stainless steel 16 Ga brads are ideal for a wide variety of secondary fix carpentry work and finishing applications such as door and window trim, skirting and panelling. The 20° angle allows for easy access into corners, especially required for terrace, parquet and siding work. Precision cut legs optimise material penetration. Specifically designed for outdoor use or humid, damp conditions. Suitable for the BN64 Cordless 20° Brad Nailer.1 x Box of 2000 Rapid 16A 20° Stainless Steel Brad Nails 38mm
The Britool E113901B 1/4in bit set, comprising of 19 pieces: 3 x Slotted Bits: 4, 4.5 and 5.5 mm.2 x Phillips® Bits: PH1 and PH2.3 x Pozidriv® Bits: PZ1, PZ2 and PZ3.6 x Torx® Bits: T10, T15, T20, T25, T30 and T40.4 x Hex Bits: 3, 4 , 5 and 6mm. The set also includes a magnetic bit holder.
Flexovit 1/3 hook & loop sanding sheets are tough and durable sanding sheets, with heavy paper backing for longer life, are ideal for general purpose sanding and stock removal. The tough and sharp High Performance Aluminium Oxide combined with a heavy paper backing makes this product extremely durable and long lasting. The hook and Loop backing allows quick and easy sheet changing. Suitable for use on wood, paint and metal. Size: 93 x 185mm. 8 hole.Size : 93 mm x 185 mm Perforated for use with Black and Decker Sanders Packed in 6s
Flexovit 1/3 hook & loop sanding sheets are tough and durable sanding sheets, with heavy paper backing for longer life, are ideal for general purpose sanding and stock removal. The tough and sharp High Performance Aluminium Oxide combined with a heavy paper backing makes this product extremely durable and long lasting. The hook and Loop backing allows quick and easy sheet changing. Suitable for use on wood, paint and metal. Size: 93 x 185mm. 8 hole.Size : 93 mm x 185 mm Perforated for use with Black and Decker Sanders Packed in 6s
Flexovit 1/3 sanding sheets are tough and durable sanding sheets, with heavy paper backing for longer life, are ideal for general purpose sanding and stock removal. The tough and sharp High Performance Aluminium Oxide combined with a heavy paper backing makes this product extremely durable and long lasting. Suitable for use on wood, paint and metal. Size: 93 x 230mm.Size : 93 mm x 230 mm (1/3 Sheet Size) Plain Packed in 10s
Flexovit 1/3 sanding sheets are tough and durable sanding sheets, with heavy paper backing for longer life, are ideal for general purpose sanding and stock removal. The tough and sharp High Performance Aluminium Oxide combined with a heavy paper backing makes this product extremely durable and long lasting. Suitable for use on wood, paint and metal. Size: 93 x 230mm.Size : 93 mm x 230 mm (1/3 Sheet Size) Plain Packed in 10s
