Bostitch Stanox staples are also known as 84 series. For use with TU-216-84-E or other tools using 84 gauge.Wire gauge 0.5 mm x 1mm, 12.3 mm crown staple with 8 mm leg length.
Finish nails and brads have heads that are rectangular. They are the same width as the shank, but the breadth of them is greater than the shank, ensuring that their holding power is enhanced. Applications include partition walls, shop and bar fitting, light framing and timber construction and most second fit applications. For use with N62FN-1, N62FNB-E & N62FNK-2 models. Note: This nail will also fit the N60FN and the N59FNK models. Applications - Partition walls, shop and bar fitting, light framing and timber construction and most second fit applications. 25° collation angleType - 15 gauge angled finish nailFinish - GalvanisedLength - 38mmQTY - Box 3655
Chamfer V grooving cutters are used for bevelling, chamfering and producing mortar grooves. Due to design, an approx. 1.0 mm flat will be found on the nose. Typical trade applications include sign making, freehand engraving, cabinet making and decorative joinery.Tooling : T.C.T.1/4in Shank.A = 45° D = 19.1 mmC1 = 9.2 mmC2 = 13 mm
Flexovit 1/3 perforated sanding sheets are tough and durable sanding sheets, with heavy paper backing for longer life, are ideal for general purpose sanding and stock removal. The tough and sharp High Performance Aluminium Oxide combined with a heavy paper backing makes this product extremely durable and long lasting. Suitable for use on wood, paint and metal. Size: 8 Parallel Hole Configuration, 93 x 230mm.Flexovit 1/3 Sanding Sheets (93 x 230mm) Perforated Fine 120g (10)
Profilers with shank mounted bearings for guidance, for use with router mounted above or below a table when following a template. Bearing guided cutters are suitable for both straight and curved work. For profiling and rebating applications only. NOT for plunge, cutting or grooving. A 3 mm approximate overlap should be left before copy profiling, also when using plastic laminate always allow laminate adhesive to dry before trimming. This avoids clogging the guide bearing.Tooling Tungsten Carbide1/2 in Shank. Angle A = 90° D = 19.1 mmC = 25.4 mm
Self-guiding triple flute cutters provide a super fine finish and longer life. Suitable for laminate or plywood overlay.This trimmer has twin bearings for stability by increasing the bearing surface.An industrial profiling tool for longer runs of work when a clean finish is needed.T.C.T.1/2in ShankA Angle = 90 .C = 38.1mm.D = 12.7mm.
Profilers with shank mounted bearings for guidance, for use with router mounted above or below a table when following a template. Bearing guided cutters are suitable for both straight and curved work. For profiling and rebating applications only. NOT for plunge, cutting or grooving. A 3 mm approximate overlap should be left before copy profiling, also when using plastic laminate always allow laminate adhesive to dry before trimming. This avoids clogging the guide bearing.A 3 mm approximate overlap should be left before copy profiling, also when using plastic laminate always allow laminate adhesive to dry before trimming. This avoids clogging the guide bearing.Tooling Tungsten Carbide1/4 in Shank.Angle A = 90 D = 15.9 mmC = 25 mm
Bearing guided rebate set for straight of curved work, this set is ideal for either stationary or portable routers. The standard rebate depth is 19.1 mm (when using 12.7 mm bearing) Available as extras are different size bearing which , when fitted, will give various rebate sizes. TCT 1/2in Shank. Diameter = 50.8 mmCcuuting length = 22.5 mmRebate = 19.1mm & 15.9mm
Popular rebate sets which include different size bearings for a choice of rebates. They provide easy setting up and accurate depth of cut. Ideal for rebating straight and shaped work pieces . Tooling TCT. By changing the bearing the size of the rebate can be altered.Supplied with four bearings.19 mm Bearing gives rebate of 7.9 mm16 mm Bearing gives rebate of 9.5 mm12.7 mm Bearing gives rebate of 11.1 mm9.5 mm Bearing gives rebate of 13.7 mmD = 35 mmC = 12.7 mm1/4in Shank. By changing the bearing the size of the rebate can be altered.Supplied with four bearings.19 mm Bearing gives rebate of 7.9 mm16 mm Diameter gives rebate of 9.5 mm12.7 mm Diameter gives rebate of 11.1 mm9.5 mm Diameter gives rebate of 13.7 mmD = 35 mmC = 12.7 mm
Popular rebate sets which include different size bearings for a choice of rebates. They provide easy setting up and accurate depth of cut. Ideal for rebating straight and shaped work pieces . Tooling TCT. By changing the bearing the size of the rebate can be altered.Supplied with four bearings.19 mm Bearing gives rebate of 7.9 mm16 mm Bearing gives rebate of 9.5 mm12.7 mm Bearing gives rebate of 11.1 mm9.5 mm Bearing gives rebate of 13.7 mmD = 35 mmC = 12.7 mm1/2in Shank.By changing the bearing the size of the rebate can be altered.Supplied with 4 bearings.Use of :19 mm Bearing gives rebate of 7.9 mm.16 mm Bearing gives rebate of 9.5 mm.12.7 mm Bearing gives rebate of 11.1 mm.9.5 mm Bearing gives rebate of 12.7 mmD = 35 mmC = 12.7 mm
These types of cutters are used for edging work and chamfer cutting on man made fibre boards, natural timbers and plastics. Tools are offered to produce various angles for chamfering. Ball bearing and pin guarded cutters enable curved work to be undertaken with bearings running along the board edge or a template. Typical trade applications include sign making, freehand engraving, cabinet making and decorative joinery.T.C.T.1/2in Shank.A = 45° C1 = 12 mmC2 = 16 mmD = 35.1mmB = 12.7 mm
Ovollo and rounding over bearing guided cutters are ideal for curved work, they can be used on natural timbers, man-made particles and fibre boards. Popular uses include edging window frames, glazing bars, cabinets, table tops, pencil rounds, trophies, shelves and fire surrounds. They can also be used to produce bullnose edge moulds. All cutters supplied with two bearings, larger bearing removes the quirk producing a round over profile.Tooling : T.C.T.1/2in Shank.R = 19 mmD = 51 mmC = 25 mmBearings = 9.5 and 12.7 mm
Self guiding cutters with bearings mounted for trimming and bevelling timber, lippings and plastic laminate edges for cabinet making, countertop production or any shaping applications. Bearing guided cutters are suitable for both straight and curved work, bearings are normally fractionally larger than cutter diameter, to avoid surface scoring. Uses:Trimming plastic or plywood overlay.Copy profiling - use the bearing to follow a template or base edge of board. A 3 mm approximate overlap should be left before copy profiling, also when using plastic laminate always allow laminate adhesive to dry before trimming. This avoids clogging the guide bearing. Tooling Tungsten Carbide1/2in Shank.Tooling Tungsten Carbide1/4in Shank.Angle A = 90 D = 6.3 mmC = 25.4 mm
Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. Two flutes give a clean finish to cut edges. 1/4in Shank.C = 19 mmD = 22 mm 55/64in OL = 50 mm
Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. T.C.T. Tooling1/2in Shank.C = 37 mmD = 19 mm 3/4 inOL = 79 mm
Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. T.C.T. Tooling1/2in Shank.C = 19 mmD = 16 mm - 5/8 in
These Cutters produce recesses with a lower rebate - double rebate. Designed to accept library/bookcase strip (Tonk Strip).Tooling : T.C.T.1/4in Shank. D1 = 13 mmD2 = 19 mmC1 = 10 mmC2 = 6 mm
342 Biscuit jointer set enables biscuit jointing with timber, man-made fibre and particle board with the router. The set includes three sizes of bearing to suit biscuits available. The correct choice of bearing for the biscuit being used will ensure the correct depth of cut. A step washer is supplied for use with bearings Ref B15, and B23. A slightly wider cut than the width of the biscuit is required to allow some lateral play for easy alignment during assembly.T.C.T.1/4in Shank.
342 Biscuit jointer set enables biscuit jointing with timber, man-made fibre and particle board with the router. The set includes three sizes of bearing to suit biscuits available. The correct choice of bearing for the biscuit being used will ensure the correct depth of cut. A step washer is supplied for use with bearings Ref B15, and B23. A slightly wider cut than the width of the biscuit is required to allow some lateral play for easy alignment during assembly.T.C.T.1/2in Shank.
Trend D-Namic two flute cutters with extra long shanks for deep grooving, rebating and morticing which are useful for template work when thickness of template restricts depth. Extra care must be taken to avoid breakage. Take more passes than usual and only cut up to half the diameter of the cutter in one pass.C = 12 mmD = 19 mm 15/32 inOL = 66mm
Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. T.C.T. Tooling1/2in Shank.Shorter shank for Makita 3600B and 3612BR, Ryobi and Hitachi Routers.Ideal for cutting kitchen worktops. C = 50 mmD = 12.7 mm
Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. Two flutes give a clean finish to cut edges. 1/4in Shank.C = 19 mmD = 12.7 mm 1/2 in
Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. T.C.T. Tooling1/2in Shank.T.C.T. Tooling1/2in Shank.C = 50 mmD = 12mm 15/32in Please note: This cutter is especially suited for drilling.
Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. Two flutes give a clean finish to cut edges. 1/4in Shank.C = 19 mmD = 10 mm 25/64 in
