Power Tool Accessories

2668 products


  • Last stock! LENOX General-Purpose Reciprocating Saw Blade Kit, 9 Piece

    Lenox LENOX General-Purpose Reciprocating Saw Blade Kit, 9 Piece

    5 in stock

    The LENOX® General-Purpose Reciprocating Saw Blade Kit, contains a selection of blades that cover a wide range of applications. Each blade uses POWER BLAST TECHNOLOGY™ to increase blade life. High-speed blasting along the cutting edge strengthens the blade to reduce breaks and increase durability. Patented T2™ Technology reduces cutting forces on each tooth and optimises chip removal to allow efficient cutting in the widest range of materials. Supplied with a handy blade carry case and the following blades: 2 x 656R Nail Embedded Wood Cutting Reciprocating Saw Blades 150mm 6 TPI 2 x 624R Metal Cutting Reciprocating Saw Blades 150mm 24 TPI 2 x 818R Metal Cutting Reciprocating Saw Blades 200mm 18 TPI 2 x 810R General-Purpose Reciprocating Saw Blades 200mm 10 TPI 1 x 960R Demolition Reciprocating Saw Blade 225mm 10 TPI

    5 in stock

    £40.49

  • LENOX 656Rct Demolition Ct Reciprocating Saw Blade 150Mm 6 Tpi

    Lenox LENOX 656Rct Demolition Ct Reciprocating Saw Blade 150Mm 6 Tpi

    The LENOX® DEMOLITION CT™ Reciprocating Saw Blade features carbide tipped teeth providing the highest performance in nail embedded wood. Each tooth is precision ground on multiple surfaces to cut through nails with ease. The high-performance carbide teeth are welded to the blade using the latest technology to increase durability and prevent tooth loss. Offering up to 10x longer life than standard bi-metal reciprocating saw blades. They have a tall, thick blade profile for maximum durability in tough demolition applications.1 x LENOX® 656RCT DEMOLITION CT™ Reciprocating Saw Blade 150mm 6 TPI

    £16.99

  • Flexovit Multi-Purpose Cutting Disc 230 X 22Mm

    Flexovit Flexovit Multi-Purpose Cutting Disc 230 X 22Mm

    The Flexovit Multi Purpose Cutting Disc is suitable for use with a wide range of general building materials. Cuts steel, stainless steel, aluminium, stone, ceramics and tiles. Reduced noise, less dust and minimal workpiece wastage. Conforms to EN 12413, OSA.

    £6.99

  • Bostitch Sb16-2.00 Straight Finish Nail 50Mm Galvanised Pack Of 2 500

    Bostitch Bostitch Sb16-2.00 Straight Finish Nail 50Mm Galvanised Pack Of 2 500

    20 in stock

    Finish Nails have heads that are rectangular. They are the same width as the shank, but the breadth of them is greater than the shank. This ensures that their holding power is enhanced, but of course the pull through force is lower than for nails with larger, Round or Clipped Heads. Primarily used for finish and trim work in the construction and joinery industries.A Bulk Pack of 2,500 50 mm 16 Gauge Straight Finish Nails for use with Stanley Bostitch Finish Nailers.Length : 50 mm.Pack : Box of 2500.

    20 in stock

    £17.49

  • Last stock! Vitrex Long Reach Sander Discs 180G (Pack Of 10)

    Vitrex Vitrex Long Reach Sander Discs 180G (Pack Of 10)

    5 in stock

    Replacement sanding discs for use with Vitrex Long Reach Sander LRS700. Easy to replace, hook and loop attachment.1 x Pack of 10 Vitrex Long Reach Sander Discs 180G

    5 in stock

    £23.49

  • Vitrex Long Reach Sander Discs 240G (Pack Of 10)

    Vitrex Vitrex Long Reach Sander Discs 240G (Pack Of 10)

    15 in stock

    Replacement sanding discs for use with Vitrex Long Reach Sander LRS700. Easy to replace, hook and loop attachment.1 x Pack of 10 Vitrex Long Reach Sander Discs 240G

    15 in stock

    £24.49

  • TREND 46/91 X 1/4 Tct 90 Shank Mounted Template Profiler 12.7 X 9.5Mm

    Trend TREND 46/91 X 1/4 Tct 90 Shank Mounted Template Profiler 12.7 X 9.5Mm

    15 in stock

    Profilers with shank mounted bearings for guidance, for use with router mounted above or below a table when following a template. Bearing guided cutters are suitable for both straight and curved work. For profiling and rebating applications only. NOT for plunge, cutting or grooving. A 3 mm approximate overlap should be left before copy profiling, also when using plastic laminate always allow laminate adhesive to dry before trimming. This avoids clogging the guide bearing.A 3 mm approximate overlap should be left before copy profiling, also when using plastic laminate always allow laminate adhesive to dry before trimming. This avoids clogging the guide bearing.Tooling Tungsten Carbide1/4 in Shank.Angle A = 90 D = 12.7 mmC = 9.5 mm

    15 in stock

    £45.49

  • Last stock! HIKOKI Hss Planer Blades For Fp20Sa / Zk2020

    Hikoki HIKOKI Hss Planer Blades For Fp20Sa / Zk2020

    5 in stock

    Replacement Planer Blades made from high-speed steel (HSS). They fit the FP20SA and ZK2020 models. Specification: Width: 82mm

    5 in stock

    £16.49

  • Faithfull Kango Shank Chisel 380Mm (914118)

    Faithfull Faithfull Kango Shank Chisel 380Mm (914118)

    20 in stock

    Faithfull Chisel steels are produced to provide high performance in all types of modern large capacity drilling and hammer drilling machines. Manufactured using traditional forging skills such as hammer work on chisels and drop stamp forging of cutting blades, they fit the most popular 21mm Hex shank machines used in the UK. Type: Chisel. Length: 380mm. Width: 25mm.Fitting: 21mm Hex shank, Kango (900/950K).

    20 in stock

    £17.99

  • Last stock! Bostitch Bright Ring Shank Coil Nails 2.1 X 25Mm Pack Of 31 500

    Bostitch Bostitch Bright Ring Shank Coil Nails 2.1 X 25Mm Pack Of 31 500

    4 in stock

    Designed for high volume operation, coils contain large quantities of nails meaning that reloading down time can be kept to a minimum. You will find them in the pallet and crate, fencing, garden furniture and the construction industries. All Coil Nails are Round Head nails. Typically: Coils of nails with diameters from 2.0 mm to 2.2 mm contain 350 nails. Coils of nails with diameters from 2.5 mm to 3.1 mm. Contain 225 nails. Roofing nail coils contain 120 nails, due to the extra large diameter of the head. 15° Collation angle Ring shank nails have a series of rings punched into the surface of the shank. A difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising, or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails. For use with: N57C-1CE heavy-duty Coil Nailer N58C-1-E Coil Nailer N58C-1-E Coil Nailer N66C-2-E Coil NailerNail Finish: Bright.Size: 2.1 x 25mm.Box quantity: 31,500.

    4 in stock

    £222.99

  • SENCO Duraspin Collated Screws Flooring / Wood Ph2 4.2 X 45Mm Pack 1000

    Senco SENCO Duraspin Collated Screws Flooring / Wood Ph2 4.2 X 45Mm Pack 1000

    20 in stock

    Senco DuraSpin® Collated Flooring & Wood screws. Yellow zinc finish, coarse thread. 50 screws per strip. CE-marked (EN145566). Suitable for both cordless and mains operated machines.Senco DuraSpin® Collated Screws Flooring / Wood. Size: PH2 4.2 x 45mm.

    20 in stock

    £37.49

  • Last stock! DEWALT DT70775 Mix Bit Set with Right-Angle Attachment, 80 Piece DEWDT70775QZ

    DEWALT DEWALT DT70775 Mix Bit Set with Right-Angle Attachment, 80 Piece

    5 in stock

    The DEWALT DT70775 Mix Bit Set is supplied in a TOUGH CASE+, this is part of a connectable case system which is TSTAK™ compatible. Individual TOUGH CASES can be clipped together for easy transportation. Contains: 2 x 25mm Phillips Bits: PH2 & PH3. 27 x 25mm Pozi Bits: PZ1, PZ2x25 & PZ3. 28 x 25mm TORX Bits: T15, T20x25, T25 & T30. 2 x 57mm Phillips Bits: PH2 x 2. 6 x 57mm Pozi Bits: PZ1, PZ2 x 4 & PZ3. 9 x 57mm TORX Bits: T10, T15, T20 x 3, T25 x 3 & T30. 1 x Modular Right-Angle Attachment. 3 x Stubby Nut Drivers: 8mm, 10mm & 13mm. 1 x Bit Holder with Torsion Zone. 1 x ALU Magnetic Sleeve.

    5 in stock

    £82.99

  • Faithfull Security S2 Grade Steel Screwdriver Bits T40S X 25Mm (Pack 3)

    Faithfull Faithfull Security S2 Grade Steel Screwdriver Bits T40S X 25Mm (Pack 3)

    Faithfull Professional Security Screwdriver Bits are designed for use with tamper-resistant, security TORX (Star) head fixings which have a small pin inside their drive recess to prevent the use of a standard TORX driver, tamper-proof fixings of this type are often found on electrical appliances. Manufactured from high-strength, heat treated ‘S2’ grade steel. These bits are shock and wear resistant and feature precision machined tips to provide an optimum fit, helping to prevent screw stripping and cam-out and provide a long working life.Pack of 3 Faithfull Security S2 Grade Steel Screwdriver Bits T40S x 25mm

    £4.99

  • Last stock! Wiha Angle Drill Driver

    Wiha Wiha Angle Drill Driver

    5 in stock

    The Wiha Angle Drill Driver comes with magnetic bit holder. Suitable for bits DIN 3126, ISO 1173, form C6.3 and E6.3. Increases your efficiency, offers unlimited access to hard-to-reach screws thanks to the 105 degree angled tool head. The variably settable stabiliser arm increases user safety.Drive: DIN 3126, ISO 1173, Style C6,3.

    5 in stock

    £53.49

  • Last stock! HALLS Rotabroachª HSS Raptor Cutter 22 x 25mm

    Halls HALLS Rotabroachª HSS Raptor Cutter 22 x 25mm

    5 in stock

    This Rotabroach™ HSS Raptor Cutter has the following specification: Diameter: 22mmCutting Depth: 25mm

    5 in stock

    £32.49

  • Last stock! HALLS Rotabroachª HSS Raptor Cutter 20 x 25mm

    Halls HALLS Rotabroachª HSS Raptor Cutter 20 x 25mm

    2 in stock

    This Rotabroach™ HSS Raptor Cutter has the following specification: Diameter: 20mmCutting Depth: 25mm

    2 in stock

    £29.99

  • HALLS 20Zasr Pilot Drill For Powerbor Cutters

    Halls HALLS 20Zasr Pilot Drill For Powerbor Cutters

    20 in stock

    20ZASR Pilot Drill For Powerbor® Cutters

    20 in stock

    £9.99

  • Bostitch 28 Bright Ring Shank Stick Nails 2.8 X 75Mm Pack Of 2000

    Bostitch Bostitch 28 Bright Ring Shank Stick Nails 2.8 X 75Mm Pack Of 2000

    20 in stock

    Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments. 28° Collation Angle Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out. (Remember only tools fitted with sequential trip should be used when working up a ladder). Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them. Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.Gauge/Diameter (mm) 2.8 Length 75 28° Collation AngleSKU S280R75 Profile RING Finish BRIGHT Description STICK NAIL 2.80-75 RING 2M Qty per box 2000 Will also fit the N80SB, FW28WW-E, N100S

    20 in stock

    £63.99

  • Last stock! Bostitch 28 Bright Ring Shank Stick Nails 2.8 X 65Mm Pack Of 2000

    Bostitch Bostitch 28 Bright Ring Shank Stick Nails 2.8 X 65Mm Pack Of 2000

    5 in stock

    Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments. 28° Collation Angle Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out. (Remember only tools fitted with sequential trip should be used when working up a ladder). Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them. Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.Gauge/Diameter (mm) 2.8 Length 65 28 Collation AngleSKU S280R65 Profile RING Finish BRIGHT Description STICK NAIL 2.80-65 RING 2M Qty per box 2000Will also fit the N80SB, FW28WW-E, N100S

    5 in stock

    £57.49

  • Bostitch 28 Bright Ring Shank Stick Nails 3.1 X 90Mm Pack Of 2000

    Bostitch Bostitch 28 Bright Ring Shank Stick Nails 3.1 X 90Mm Pack Of 2000

    20 in stock

    Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments. 28° Collation Angle Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out. (Remember only tools fitted with sequential trip should be used when working up a ladder). Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them. Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.Gauge/Diameter (mm) 3.1 Length 90 28 Collation AngleSKU S310R90 Profile RING Finish BRIGHT Description STICK NAIL 3.10-90 RING 2M Qty per box 2000Will also fit the N80SB, FW28WW-E, N100S

    20 in stock

    £67.99

  • Faithfull Flap Disc 100Mm Fine

    Faithfull Faithfull Flap Disc 100Mm Fine

    20 in stock

    The Faithfull Flap Discs have been designed for use with most angle grinders, flap discs are manufactured from long lasting zirconia alumina. Resin bonded for extra strength and durability, ideal for use on wood, metal and plastic.Diam Size 100 mm Bore 16 mmGrade Fine (80 Grit)

    20 in stock

    £6.99

  • Last stock! Faithfull Router Bit Tct 3.2Mm Corner Bead 1/4In Shank

    Faithfull Faithfull Router Bit Tct 3.2Mm Corner Bead 1/4In Shank

    5 in stock

    A bearing guided tungsten carbide tipped cutter designed to produce a decorative edge when working on MDF, softwoods, hardwoods, and plywood. 1/4in Shank Radius: 3.2mm Diameter: 22mm

    5 in stock

    £25.49

  • DEWALT Series 40 Circular Saw Blade 216 X 30Mm X 80T Tcg/Neg

    Dewalt DEWALT Series 40 Circular Saw Blade 216 X 30Mm X 80T Tcg/Neg

    20 in stock

    The DEWALT Series 40 Extra Fine Finish Circular Saw Blade is designed for use in stationary saws. With large, general purpose K10 carbide tips for cutting wood and non-ferrous metals. They can be resharpened up to 15 times. High precision laser manufacture ensures a flat blade body and engineered expansion slots prevent blade overheating and warping. These blades are designed with triple chip grind geometry which gives an excellent surface finish on the workpiece.This DEWALT Series 40 Circular Saw Blade has the following specification: Finish: Extra Fine.Blade Diameter: 216mm.Blade Bore: 30mm.Tooth Count: 80.Plate Thickness: 1.8mm.Kerf Thickness: 2.6mm.Grind Type: TCGN.Rake Angle: -5°.

    20 in stock

    £86.99

  • DEWALT Sabre Blade Fast Cuts Wood With Nails Plastics 228Mm Pack Of 5

    Dewalt DEWALT Sabre Blade Fast Cuts Wood With Nails Plastics 228Mm Pack Of 5

    The DEWALT bi-metal construction blades combine HCS and HSS for increased flexibility and durability. They can be used for fast cutting in wood, wood with nails and tough plastics. The universal shank fits all major brands including DEWALT, Bosch, Hitachi, Flex, Makita, Metabo and Skil.The DEWALT DEWDT2349QZ reciprocating blade is ideal to be used for fast cuts in wood with nails and tough plastics. The blade has a new Plunge point tip for accurate plunge.

    £25.49

Login

Forgot your password?

Don't have an account yet?
Create account