The sharpening of the two blade edges and the design of the handle on this Hultafors Electricians Knife are optimised for cable stripping. The knife blade is made from Japanese 1.5 mm knife carbon steel that has been hardened to 58-60 HRC. A unique method for attaching the sheath around a button on work clothes means it does not loosen, but is easy to remove. The sheath fits just as well on a belt as on buttons. The handle and sheath are made from extra durable PP plastic. Blade Length: 33mm.Overall Length: 158mm.Supplied loose.
Hultafors Dry-Marker Refills supplied in a smart container with 10 leads for marking on all types of surfaces. The container protects the leads during transport and only ejects one lead at a time. Clips for easy storage in a pocket or bag. These refills fit the Hultafors Dry-Marker. Available options: either graphite only or graphite, red and yellow chalks.1 x Pack of 10 Hultafors Dry-Marker Refills containing: 4 x Graphite Leads3 x Red Chalk Leads3 x Yellow Chalk Leads
The Faithfull Spring Clamp is easy-to-use and cost effective. Made from durable engineering plastic and fitted with a bi-material handle for increased comfort and ease of use. Ideal for general-purpose clamping needs, from holding material whilst fixing, to simple tasks such as securing sheeting or tarpaulins.Faithfull Spring Clamp 50mm (2in) supplied in a pack of 4.
Blackedge carpenters pencils have an oblong section which can be sharpened to a chisel shaped edge. This eliminates the tendency of a pointed pencil to follow the grain. Available in three grades - Green (hard). For Hardwoods, Brickwork and Plastered wallsRed (medium). For General CarpentryBlue (soft). For Softwoods and newly felled timberCard of 12. Hard (Green) Ideal for marking Hardwoods, Brickwork and Plastered walls.
Wrecking bars are an essential tool for all builders, carpenters and plumbers and widely used in factories, warehouses and the farming industry. Manufactured from octagonal steel cross section with hardened and tempered chisel and claw ends, which ensure maximum strength and durability. For opening packing cases, pulling out nails, levering off shuttering etc.Size: 750 x 19mm (30 x 3/4 in).
Blackedge carpenters pencils have an oblong section which can be sharpened to a chisel shaped edge. This eliminates the tendency of a pointed pencil to follow the grain. Available in three grades - Green (hard). For Hardwoods, Brickwork and Plastered wallsRed (medium). For General CarpentryBlue (soft). For Softwoods and newly felled timberCard of 12. Soft (Blue) Ideal for marking Softwoods and newly felled timber.
PlastiKote Trade Leak Detector Spray for the detection of leaks in gas pipes. It has a non-combustible, non-corrosive formula that can be removed with water.
Vitrex Tile Trowel with U & V Notches. It is made from lightweight plastic with a comfortable ergonomic handle. Dual edged for use with bonding and floor tile adhesives. Size: 115 x 278mm (11 x 4.1/2in) This Vitrex Notched Adhesive Trowel has been designed for use with wall and floor tile adhesives. Ideal for installing underfloor heating. Specification: Size: 115 x 280mm (11 x 4.1/2in)V Notches: 6mmU Notches: 20mm
The Vitrex Mixing Paddles are designed to mix sticky and viscous materials, such as tile adhesive, bonding mortar, jointing compound, ready mixed plaster, floor screed and fillers. Suitable for use with the MIX850 Power Mixer and MIX1400 Power Mixer.The Vitrex MIXADH140 Mixing Paddle has the following specifications: Blade Diameter: 140mm.Length: 600mm.
The Thor Hide hammer has split cast iron head with two hide faces fastened securely to the handle with two socket head cap screws. The head design allows quick adjustment or replacement of either the handle or the faces, while the faces are designed to wear and can be rotated for even wear. There are 5 different weights to choose from in this range. For use as a heavy-duty, multi purpose soft-faced hammer in most industries for assembly, repair and maintenance operations.Size: 1.Diameter: 32mm (1 1/4 in).Weight 690g (1 1/2 lb).
Thor super plastic hammers have a malleable iron head fitted with cylindrical ultra-high molecular weight polythene faces which are designed to wear and be replaced. Available in 3 different weights. The ultra-high molecular weight polythene heads provide high impact, durability and high abrasive resistance. The faces will not fracture, splinter or delaminate. Ideal for use as a general-purpose, soft-faced hammer in engineering applications for assembly, repair and maintenance operations as an alternative to a rawhide faced hammer.Size: 2.Weight 790g (1 3/4lb).Diameter 38mm (1 1/2 in).
Thor super plastic hammers have a malleable iron head fitted with cylindrical ultra-high molecular weight polythene faces which are designed to wear and be replaced. Available in 3 different weights. The ultra-high molecular weight polythene heads provide high impact, durability and high abrasive resistance. The faces will not fracture, splinter or delaminate. Ideal for use as a general-purpose, soft-faced hammer in engineering applications for assembly, repair and maintenance operations as an alternative to a rawhide faced hammer.Size: 4.Weight 1900g (4 1/2lb).Diameter 50mm (2 in).
Thor Hide mallets have a one piece cylindrical compressed hide head, that provides a large striking surface with a relatively light head weight. These hide mallets are widley used in sheet metal forming, the jewellery trade and used on copper, brass and other soft materials that need to be shaped etc. These Mallets are fitted with an oval wood handle.Size: 6. Weight 680g (1 1/2 lb).Diameter 70 mm (2 3/4 in).
The Thor Thorex Nylon Hammer for impact with a clean finish. Its Chrome-plated Zinc head (except THO720) is durable and corrosion-resistant, this head adds weight and strength while maintaining a clean, polished look.Engineered for balance and durability. All have two white durable nylon faces except THO710R and THO712R which have one white nylon and one soft grey face.The durable nylon faces can be replaced to upgrade or extend the life of your hammer. The white is made from impact-resistant Nylon 6/6 (Shore D57-61) for long-lasting performance, the ultimate versatile choice for both light and heavy-duty assembly work. Made from the grey soft PVC (Shore A63-73) that protects delicate surfaces for mark-free strikes.Fitted with a durable anti-vibration, wooden handle. Crafted from high-quality hardwood, it minimises recoil for enhanced comfort and control. Recommended for general maintenance, assembly work and frame construction, where force is needed without compromising surface integrity.
1 x Thor 714N Thorex Nylon Hammer 44mm 760g
Feeler gauges are used to adjust tappets, spark plugs, distributor points, check bearing clearances and gear play, fitting pistons, rings and pins and gauging narrow slots. Leaves are tempered steel, easily removed and replaced. There is a locking device on all sets.Millimetre Reading Gauges with Straight leaves 12.7 x 77mmNo. of leaves: 13 Range: 0.03 - 0.5mm ( 0.03- 0.10 by 0.01 mm steps, 0.15, 0.20 to 0.50 by 0.1 mm steps)
Bahco Pipe Slices are automatic tube cutters that fit directly over the pipe and cuts with a simple twist. They are compact in size, making them ideal for work in confined spaces. With orange painted zinc body.Size 15mm.
1 x ITL Insulated 3/8in Drive Extension 75mm (3in). The ITL Insulated 3/8in Drive Extensions are made from injection moulded nylon 11, which exceeds the requirements of IEC 60900, the industry standard for live line working. In addition, this tool meets the requirements of Category 'C', which requires it to perform at extreme temperatures of -40°C to ;70°C, making it unique in this category. These insulated tools are the toughest in the market, being virtually indestructible. With a lifetime warranty on both the tool and insulation. 75mm (3in)
Stanley Club Hammer with a fibreglass core for greater strength and longer durability. The shaft is covered by an ergonomic, anti-slip, bi-material handle. It has a drop forged alloy steel head with polished faces and chamfered edges. The head and handle have a reinforced connection, held by a 2-component epoxy resin adhesive.1 x Stanley Fibreglass Club Hammer 1.25kg (2.3/4lb)
The MaxSteel heavy-duty bench vice is made from cast iron for strength and durability. The base bolts directly to the workbench surface for stability, and swivels and locks for versatility. Roll-formed screw threads ensure smooth operation and durability. Chrome plated hardware resists corrosion.Size: 125mm (5 in).
Part of the Stanley Tools Transmodule System, a modular mechanics storage system ideal for the workshop. Designed to use with compatible Transmodule system storage cabinets. All the sockets feature Maxi Drive, that helps reduce fastener rounding and are made from Chrome Vanadium Steel. The bit sockets are made from S2 steel, HRC 60 ±2 with a 20% higher torque than CrV. The extensions are also made from Chrome-Vanadium steel with a full polished finish. The ratchet features a socket safety lock and a reverse lever with rotation direction displayed. Made from Chrome-Vanadium steel and fitted with a chemical resistant, ergonomic bi-material handle and quick release button. Contains the following: 13 x Standard Sockets: 4, 4.5, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 13 & 14mm. 12 x Deep Sockets: 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 13 & 14mm. 3 x Slotted Bit Sockets: 4, 5.5 & 7mm. 3 x Pozidriv Bit Sockets: PZ1, PZ2 & PZ3. 3 x Phillips Bit Sockets: PH1, PH2 & PH3. 6 x Hex Bit Sockets: 2, 2.5, 3, 4, 5 & 6mm. 8 x Torx Bit Sockets: T6, T7, T8, T9, T10, T15, T20, T25. 6 x Torx Sockets: E4, E5, E6, E7, E8, E10. 2 x Extension Bars: 50 & 100mm. 1 x Universal Joint. 1 x Quick Release Ratchet. 1 x Sliding Tee. 1 x Driver Handle. 1 x NP9 Pear Headed Ratchet.
Used to adjust tappets, spark plugs, distributor points, checking bearing clearances and gear play, fitting pistons, rings and pins and gauging narrow slots. Leaves are tempered steel, easily removed and replaced. Locking device on all sets.Inch Reading Gauges with Straight leaves 1/2 x 3 1/32 in No. of leaves: 26 Range: 0.0015 - 0.025 in ( 0.0015, 0.002, 0.0025, and 0.003 to 0.025 by 0.001 in steps)
The Faithfull No.4 Smoothing Plane is designed for smoothing and final finishing. Made with a quality grey cast iron body for strength and stability with precision ground base and sides for flatness and squareness. Machined seatings eliminate movement and blade judder. A lever cap with a brass locking screw secures the blade assembly and enables easy release for sharpening. Wooden handles and guidance knobs maximise user comfort. A solid brass blade adjustment nut completes the appeal of these traditional tools. Cutter Width: 50mm.Overall Length: 250mm.This Faithfull No.4 Smoothing Plane is supplied loose, unboxed.
The Teng Tools Impact Sockets are specifically designed for use with power tools and air tools. They are manufactured from chrome molybdenum steel in accordance with GGG-W-6608, providing the highest quality. The sockets have a 1/2in drive, and are suitable for both industrial and automotive applications. Each socket is individually branded and size marked for quick identification.This Teng Impact Socket has the following specification: Size: 19mmLength: 38mm
IRWIN Record Medium-Duty Forged G Clamp are a drop forged steel clamp and the slim section permits use in situations where space is limited. Particularly useful for the craftsman with smaller work, the boat builder and the handyman. Have a blue stove enamelled finish. Come in the following sizes: REC1192: 50mm.REC1193: 75mm.REC1194: 100mm.REC1196: 150mm.IRWIN Record Medium-Duty Forged G Clamp Size: 76mm (3 in). Throat depth: 38mm (1 1/2 in).
This Teng Tools Hex key with T handle, has a short arm and a long arm. The short arm allows excellent leverage, allowing easy tightening and loosening. The long arm of the Hex key has a ball point head, which allows a working angle of up to 30 degrees, and therefore improves access. Manufactured from chrome vanadium steel for toughness and durability.The TEN510505 T Handle Hex Driver has the following specifcations:Size: 5.0mm.Short arm length: 15mm.Long arm length: 150mm.
The Marshalltown Permaflex Plasterer Trowels ensure a perfect finish every time. They have a high grade, ultra flexible, 0.3mm stainless steel blade with an xtralite aluminium alloy mounting and stainless steel rivets. The blade has been bonded and taped for increased blade security. It has been designed to flex for easier final smooth and finishing of multi finish, skimming and board finish plasters. Fitted with a resilient DuraSoft® handle that provides a soft feel, reduces fatigue, and offers excellent durability. Made in the USA.1 x Marshalltown Permaflex Plasterer Trowel DuraSoft® 13in
The RIDGID Heavy-Duty Straight Pipe Wrench has a sturdy, cast-iron housing and I-beam handle with full floating forged hook jaw, featuring self cleaning threads with replaceable hook and heel jaws.RIDGID Heavy-Duty Straight Pipe Wrench Size: 900mm (36in)Capacity: 125mm (5in)Weight: 8.7kg
The RIDGID Heavy-Duty Straight Pipe Wrench has a sturdy, cast-iron housing and I-beam handle with full floating forged hook jaw, featuring self cleaning threads with replaceable hook and heel jaws.Specification: Size: 250mm (10in)Capacity: 40mm (1.1/2in)Weight: 0.8kg
The ITL Insulated 3mm Cooker Knob Hex Driver for use on connector boxes. Made from injection moulded nylon 11 which exceeds the requirements of IEC 60900, the industry standard for live line working. In addition, this tool meets the requirements of Category 'C', which requires it to perform at extreme temperatures of -40°C to and70°C, making it unique in this category. These insulated tools are the toughest in the market, being virtually indestructible. With a lifetime warranty on both the tool and insulation, plus a 30 day no quibble money back guarantee.
The Wiha SoftFinish electric slimFix Screwdrivers come with a high quality Chrome vanadium steel blade, through hardened with a black-finish. Insulation is moulded directly onto the blade. Individually tested at 10,000 V AC and approved for 1,000 V AC.Patented SoftFinish handle ensures work is kind to hands and muscles. Recommended by doctors and therapists at the German Campaign for Healthier Backs. slimFix handles have been specially developed for electric applications, blades are up to 33% slimmer. The unique Wiha handle-length concept provides optimum balance of torque and control. Manufactured according to IEC 60900. This 6 Piece Set contains the following: 4 x Slotted Screwdrivers: 3.5 x 100mm, 4.0 x 100mm & 5.5 x 125mm.2 x Phillips Screwdrivers: PH1 x 80mm & PH2 x 100mm.1 x PlusMinus Screwdriver: SL/PZ2 x 100mm.
Clamping with leverage Speed, safety and strength The original BESSEY lever clamps are lightweight, easy-to-handle, dimensionally stable, and torsion resistant. And the best thing is: they can clamp up to 5 x faster than conventional clamps. This is because they use the natural force of the lever, meaning that with just a small amount of effort they can quickly produce large clamping pressures. This is particularly valuable in situations where many clamps have to be applied in a short time, with no risk of loosening due to vibrations. Try it out! The lever clamp GH allows you to clamp up to 5 x faster than with conventional clamps. Rapid - Up to 5 x faster than conventional clampsSecure - Unaffected by vibrationsStrong - High clamping forceYour benefits at a glance: Secure ratchet mechanismThe ratchet mechanism ensures rapid, controlled, vibration free clamping. Hardened cam at the end of the lever ensures a long service life. Extremely sturdyFixed bracket and pressure plate are produced and tempered from a single piece, thus very torsion-resistant. This guarantees you maximum tensile strength and sturdiness. Forged sliding armThe sliding arm is serrated and made from tempered, drop-forged steel. For an extremely long service life. Ergonomically shaped clamping leverThe powder-coated clamping lever and the plastic-coated release lever are also remarkably ergonomic.The Bessey GH40 Lever Clamp has the following specification: Clamping Force: up to 8,000N.Opening: 400mm.Throat Depth: 120mm.Rail: 25 x 12mm.Weight: 2.41kg.
The RIDGID® Micro IR-200 Non-Contact Infrared Thermometer provides simple, quick and accurate surface temperature readings at the push of a button. Simply squeeze the trigger and point the ultra-sharp dual class II lasers at the surface being measured. Ultra-Sharp Dual Class II Lasers easily identify the surface area being measured. Has a 30 to 1 Distance To Spot Ratio, this allows you to take more accurate measurements from a farther distance. With adjustable emissivity to accurately measure the temperature of virtually any surface. Uses audible and visual, high and low alarms to quickly alert user to temperatures outside of the ranges that are set. It has a bright backlit display which can be toggled on in poorly lit areas and can be mounted on a tripod for repeatable, precise temperature measurements. Specification Temperature Range: -50 to 1200°C (-58 to 2192°F),Distance To Spot Ratio: 30 to 1.Response Time: <150ms.Temperature Display: Current Temperature & MAX Temperature.Measurement Units: Fahrenheit & Celsius.Power Source: 1 x 9 Volt Battery (Included).Weight: 0.20kg.
Faithfull FSC Carpenters Sliding Bevel for marking out, checking and transferring angles. The blued spring steel blade can be set to any angle and locked in position by means of a brass wing nut. The quality hardwood stock is finely machined and shaped with brass end caps. This product is made with FSC® 100% Certified Wood from well-managed forests.
1 x Faithfull FSC Carpenters Sliding Bevel 270mm (10.1/2in)
The Facom 249.G sheathed drift punches are tough and durable. With very high tensile strength, these punches feature a head hardened to 43 HRc and a long shank hardened to 58 HRc. The handles are ergonomically shaped for comfort and shock absorption. Ideal as an aid in aligning bolt or rivet holes prior to inserting a fastener.The FCM249G2 Sheathed Punch has the following specifications:Point diameter: 1.95mm.Length: 140mm.
