Dormer E500 straight flute taps are the only type of taps that can be used by hand, but they may also be used in a machine if required. Extremely versatile, can tap through or blind holes in most materials. When tapping blind holes straight flute taps should be used in sets. The three taps which form a set are known by more than one name. 1. Taper or First tap2. Second or Intermediate tap3. Bottoming, third or plug tap. Metric coarse straight flute taps. Tolerance: Class 2 for 6H FitSurface treatment: BrightMaterial: HSS High Speed SteelChamfer No: 1,2 and 3, Serial no 4 and 5Flute Geometry: Straight Flutes ISO529Size 20.0mm x 2.5 second
The Facom 249.G sheathed drift punches are tough and durable. With very high tensile strength, these punches feature a head hardened to 43 HRc and a long shank hardened to 58 HRc. The handles are ergonomically shaped for comfort and shock absorption. Ideal as an aid in aligning bolt or rivet holes prior to inserting a fastener.The FCM249G10 Sheathed Punch has the following specifications:Point diameter: 9.80 mm.Length: 230mm.
Hardened steel punches carefully heat treated for long life. Precisely knurled body with square head which gives a good striking area and prevents the punch from rolling.Size 1.5mm (1/16 in).Length 100mm (4 in)
Hexagonal bodied parallel pin punches with extra long pins. Used for driving out long retaining pins. The pin should be first started with a hand or taper punch to avoid damage to the point of the pin punch. Pin length: 63mm (2.1/2in).Overall length: 152mm (6in).Size. 6.4mm (1/4 in).
Wad punches are used for cutting holes in soft materials or for producing discs from the material being cut.One piece forging with ground and polished tapered section.Size 13mm (1/2 in)
Wad punches are used for cutting holes in soft materials or for producing discs from the material being cut.One piece forging with ground and polished tapered section.Size 44mm (1 3/4 in)
A hardened and tempered parallel pin punch, which is used for removing pins in parallel holes. The pin should be first started with a hand or taper punch to avoid damage to the point of the parallel punch.Size 4.0mm (5/32 in)
The Moore & Wright MW521-01 Combination Set is supplied with three measuring heads (Square, Protractor and Centre) that can be attached to the stainless steel ruler, allowing versatile measurements and marking on various types of workpieces. The stainless steel rule has engraved graduations; one side metric, one side imperial and hardened and ground slide ways. Range: 180°.Length: 300mm (12in).
The Moore & Wright Engineer's Levels have a precision ground cast base with a V-groove for location on cylindrical work. Each level is fitted with a main, cross and plumb vial and the main vial is protected by a rotating shroud. The solution in the vials maintains colour and fluidity under all workshop conditions and the main vial has a sensitivity of 1 minute.The Moore & Wright ELM Engineer's Levels has the following specification: Length: 300mm (12in).Width: 36mm (1.42in).Height: 58mm (2.28in).Resoultion: 0.3mm per metre (0.0035in per foot).
The Moore & Wright Firm Joint Outside Calipers are manufactured from polished tool steel and have a large headed nut and screw assembly that provides a firm and rigid friction joint, with no play. The sizes listed are the effective leg length which is measured from the joint assembly. The Firm Joint Outside Calipers are manufactured to BS3123 standards. Note: Firm joint caliper capacities are generally 1/3 greater than the effective leg length.The Moore & Wright 3316R Firm Joint Outside Calipers have the following specification: Size: 150mm (6in).
The Moore & Wright 420 Series Dial Test Indicators have highly precisioned, fully jewelled bearings and carbide points. There are two dovetail clamps on these models. The 420 Series allow automatic reversal of measuring direction and there is a rotating dial for increased ease of use. Styli Length: 12mm (1/2in).The Moore & Wright MW420-03 Dial Test Indicators has the following specification: Range: 0.8mm.Resoultion: 0.01mm.Dial Reading: 0-40-0.Dial Diameter: 25mm.
An extremely handy pocket sized reference booklet of data charts and tables for the drawing office, toolroom or workshop. This metric revision publication is produced by Zeus Precision Charts Ltd, who are members of the British Standards Institution. The 28 laminated pages contain data on standard drill sizes and decimal equivalents, tapping drills and clearances for metric and imperial threads, BS4500 tolerances, hardness comparisons, jig boring co-ordinates for equally spaced holes, allowances for sheet metal bending and Morse tapers. Also, long tables for sine, cosine, tangents and cotangents.
The Starrett Fractional Display Caliper is lightweight, comfortable, and easy to use. Made from hardened stainless steel, it has a slim profile and a clear LCD display, reads 0.01mm, .0005in or 1/64in. The display includes function buttons for zeroing and unit switching (mm, inch, F). A fine adjustment thumb wheel allows for easy measuring and a lock screw to secures the slide position. To save battery life it has an auto-off after 5 minutes. It also features a low battery warning system with flashing display and a USB port for data output. Comes with: a battery cover wrench for easy access and a hardwearing case. Conforms to DIN862 standard. Specifications: Power: Single SR44/LR44 Long-life Battery.Max. Measuring Speed: 1.5m/sec or 60in/sec.1 x Starrett Fractional Display Caliper 200mm.
The Starrett Fractional Display Caliper is lightweight, comfortable, and easy to use. Made from hardened stainless steel, it has a slim profile and a clear LCD display, reads 0.01mm, .0005in or 1/64in. The display includes function buttons for zeroing and unit switching (mm, inch, F). A fine adjustment thumb wheel allows for easy measuring and a lock screw to secures the slide position. To save battery life it has an auto-off after 5 minutes. It also features a low battery warning system with flashing display and a USB port for data output. Comes with: a battery cover wrench for easy access and a hardwearing case. Conforms to DIN862 standard. Specifications: Power: Single SR44/LR44 Long-life Battery.Max. Measuring Speed: 1.5m/sec or 60in/sec.1 x Starrett Fractional Display Caliper 300mm.
The Starrett Fractional Display Caliper is lightweight, comfortable, and easy to use. Made from hardened stainless steel, it has a slim profile and a clear LCD display, reads 0.01mm, .0005in or 1/64in. The display includes function buttons for zeroing and unit switching (mm, inch, F). A fine adjustment thumb wheel allows for easy measuring and a lock screw to secures the slide position. To save battery life it has an auto-off after 5 minutes. It also features a low battery warning system with flashing display and a USB port for data output. Comes with: a battery cover wrench for easy access and a hardwearing case. Conforms to DIN862 standard. Specifications: Power: Single SR44/LR44 Long-life Battery.Max. Measuring Speed: 1.5m/sec or 60in/sec.1 x Starrett Fractional Display Caliper 150mm.
Stanley 158501 FatMax® Interchangeable Nail Set with two nail set sizes (1/32in and 1/16in). Bi-material grip for comfort and reduced slipping. 1/4in locking system accepts standard screwdriver bits.
These Dormer Metric Coarse Combination Drill & Spiral Flute Taps allow drilling/threading holes in one single operation. They are made from High Speed Steel and are suitable for use on most materials. They can be used in reversible, variable speed power tools. Manufactured to ISO Standards.Size: M5Tip Diameter: 4.2mmOverall Length: 69mm
The Moore & Wright MW279-01A Micrometer Stand is designed for micrometers up to 100mm (4in). It has a painted cast iron base with plastic covered clamping jaws and the angle of the jaws can be adjusted.
The Facom 249.G sheathed drift punches are tough and durable. With very high tensile strength, these punches feature a head hardened to 43 HRc and a long shank hardened to 58 HRc. The handles are ergonomically shaped for comfort and shock absorption. Ideal as an aid in aligning bolt or rivet holes prior to inserting a fastener.The FCM249G14 Sheathed Punch has the following specifications:Pointed diameter: 13.80mm.Length: 290mm.
Straight edge for accurate marking out with a carpenters pencil or metal scriber. Accuracy is 0.01% of the length of the straight edge.Size: 750 x 53mm (30 x 2.08in).
A hexagonal bodied Rivet Snap with the working end heat-treated to ensure a long life.This tool is used for the forming of heads on solid rivets.Size 2.5 x 115mm (3/32 x 4 1/2 in)
1 x Moore & Wright 4003 Engineer's Square Grade B 75mm (3in)in Retail Packaging. Specifications: Blade Size: 104.8 x 25.4mm.Stock Size: 68.5 x 25.4mm.Inner Working: 49.3 x 79.4mm.
The Moore & Wright Traditional External Micrometer has a blue textured frame finish with tungsten carbide measuring faces and a tapered bow frame. The 'speeder' type ratchet, locking lever and adjusting key make this micrometer easy to use. It has a 6.5mm spindle diameter. The micrometers are manufactured to BS870, DIN 863/1, ISO 361 standards. Supplied in plastic pocket case.The 1965 Traditional External Micrometer has the following specification: Micrometer Range: 0-1in. Measuring Faces: Flatness: 0.00005in, Parallelism: 0.0001in, Accuracy: 0.0001in.Resolution: 0.001in.
The Facom 249.G sheathed drift punches are tough and durable. With very high tensile strength, these punches feature a head hardened to 43 HRc and a long shank hardened to 58 HRc. The handles are ergonomically shaped for comfort and shock absorption. Ideal as an aid in aligning bolt or rivet holes prior to inserting a fastener.The FCM249G16 Sheathed Punch has the following specifications:Point diameter: 15.70mm.Length: 310mm.
Faithfull Nail punch with a square head which provides a larger striking area and stops the punch rolling off the bench. Accurately hardened and tempered with a precision formed concave tip for better nail contact. Designed to drive nail heads below the surface of the wood.Point Diameter: 2.5mm (3/32in)Length: 100mm (4in)
Dormer E500 straight flute taps are the only type of taps that can be used by hand, but they may also be used in a machine if required. Extremely versatile, can tap through or blind holes in most materials. When tapping blind holes straight flute taps should be used in sets. The three taps which form a set are known by more than one name. 1. Taper or First tap2. Second or Intermediate tap3. Bottoming, third or plug tap. Metric coarse straight flute taps. Tolerance: Class 2 for 6H FitSurface treatment: BrightMaterial: HSS High Speed SteelChamfer No: 1,2 and 3, Serial no 4 and 5Flute Geometry: Straight Flutes ISO529Size 5.0mm x 0.8 second
Faithfull Letter and number punches are used for hand marking metals and other hard materials. They are useful for stamping personal identification or post codes on tools, cycles etc., as frequently recommended by police and insurers. The letter or number sizes as shown, relate to the height of the characters. The punches are manufactured from high quality tested carbon steel with double induction hardened heads to ensure high quality impressions. The body is hardened and the head is tempered to prevent chipping when hammered.Contents : 1, 2, 3, 4, 5, 6, 7, 8, 9, 0 (9 is achieved by reversing 6).Set supplied in plastic box.Size : 2mm (5/64 in).
Industrial quality bar type tap wrench manufactured from a high-quality steel. The wrench body is black powder-coated and houses two steel jaws. The handle is knurled for positive grip and control.Tap size capacity: M4 - M14
The Faithfull Magnetic Square Welding Clamp enables fast and accurate holding of ferrous metals for welding and assembly. The clamp contains a strong magnet and features angled edges for precise alignment of metal workpieces. It will securely hold round and square tubing, angle and flat stock. Through-holes enable multiple clamps to be fixed together when working on larger projects. Ideal for use by welders and fabricators. Achievable Angles: 45°, 90° & 135°Pull Power: 20kgSize: 100 x 95 x 19mm
The Faithfull Spring Dividers have polished natural steel finish legs made of flat stock. They are carefully balanced, with heat treated points. A strong but flexible bow spring and centrally located adjustment screw give a smooth and precise action.Size 200mm (8 in)
The Faithfull Spring Dividers have polished natural steel finish legs made of flat stock. They are carefully balanced, with heat treated points. A strong but flexible bow spring and centrally located adjustment screw give a smooth and precise action.Size 100mm (4 in)
Widely used in automotive, aviation, diesel and farm equipment manufacture and also in jig, fixture and gauge work. Packed individually in envelope. Metric gauge 300 mm long.Thickness: 0.50mm
These Faithfull punches are made from uniformly heat treated carbon steel and are used for removing pins in parallel holes. The removal of the pins should first be started with a hand or taper punch to avoid damage to the end of the parallel punch.The set of eight punches include one of each of the following.1.5mm , 2.5mm , 3.0mm , 4.0mm , 5.0 mm , 5.5mm , 6.0mm and 8mm Length: 100mm (4 in)
Imperial 13in lengths of high carbon bright steel, precision ground to very close tolerances; Above 1 in + - 0.0005in.Below 1 in + - 0.00025in. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 7/16 in
A hardened and tempered parallel pin punch, which is used for removing pins in parallel holes. The pin should be first started with a hand or taper punch to avoid damage to the point of the parallel punch.Size 5.5mm (7/32 in).
Extra long pin punch. Hardened and tempered with a knurled grip. The drive pin sections are 90mm (3.1/2in) long and the diameters of the punches are slightly under the sizes listed. Length: 200mm (8in).Size 8mm (5/16 in)
