Hardened steel punches carefully heat treated for long life. Precisely knurled body with square head which gives a good striking area and prevents the punch from rolling.Walleted set of 4 containing one of each of the following sizes. 1/16, 3/32, 1/8, and 3/16 in.Length 4 in
A precision manufactured automatic centre punch which aids accuracy through the single handed operation which alleviates the need for a hammer. Depth of impression can be adjusted via the screw cap. Length: 125mm (5in).
A quick and easy way to cut clean metric sized holes in sheet metal up to 16 gauge. The special design allows even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches are sold singly without key, which should be ordered separately. Thread the punch onto the hexagonal screw and then pass the hexagonal screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting hexagonal screw until it touches the metal sheet. Use a hexagonal key to turn the hexagonal screw. The screw will pull the punch through the metal and a hole will result. Please note these instructions apply to cutters up to 15 mm in size, for cutters 15 mm and over have a different configuration. Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.Size.30.0mm.Key Type.MB. 8mm hexagonal wrench
The Faithfull Double Ended Scriber has a knurled body to provide a positive grip. The two sharp ground points are heat-treated to retain their edge.One point is set at right angle increasing flexibility for marking and scoring. Length: 186mm (7.1/3in).
Type 117 Centre punches are manufactured from specially selected steel, hardened and properly tempered. They are well proportioned, nicely finished and have a knurled finger grip. The points are ground at the proper angle to give maximum service, and the tips are accurately centered. Length: 100mm (4in).Size 1.5 x 75mm (1/16 x 3 in)
A quick and easy way to cut clean imperial sized holes in sheet metal up to 16 gauge. The special design allows an even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches boxed singly without key, which should be ordered separately. To use these punches they require a hole to be drilled through the sheet metal (large enough to clear the heagonal Screw) then the Die and hexagonal screw are threaded through the sheet metal then onto the die nut and screw die nut. When the hexagonal screw is tightened the punch will cut cleanly and evenly through the metal.Size. 9/16 in.Key Type. 7/32 in hexagonal wrench
Feeler strips are widely used in automotive, aviation, diesel and farm equipment manufacture and service. Also used in jig, fixture and gauge work. Packed individually in an envelope. Length: 300mm (12in).Inch Gauge 12 in long Thickness: 0.005 in
Feeler strips are widely used in automotive, aviation, diesel and farm equipment manufacture and service. Also used in jig, fixture and gauge work. Packed individually in an envelope. Length: 300mm (12in).Inch Gauge 12 in long Thickness: 0.0015 in
The Faithfull Magnetic Multi-Angle Welding Clamp enables fast and accurate holding of ferrous metals for welding and assembly. The clamp contains a strong magnet and features angled edges for precise alignment of metal workpieces. It will securely hold round and square tubing, angle and flat stock. Through-holes enable multiple clamps to be fixed together when working on larger projects. Ideal for use by welders and fabricators. Achievable Angles: 30°, 45°, 60°, 75°, 90°, 105°, 120° & 135°Size: 100 x 65 x 14mm
The Faithfull Shallow Pot Magnets are designed for clamping directly onto a steel surface. The large, powerful ceramic magnet is encased within a protective steel shell. Magnetic on one face only, creating a solid clamping force for holding and lifting metal parts. The shallow depth allows use in confined spaces. They can be secured with bolts through their centre holes and their heavy lifting capacities make them a great choice for use in industrial settings.Diameter: 70.0mmHeight: 6.35mmPull Power: 15.0kg
The Moore & Wright 401 Series Dial Indicator has an aluminium body and a tungsten carbide measuring tip. It has an adjustable bezel with stop screw and features tolerance indicators. Manufactured to ANSI B89.1.10 standard. Specifications:Range: 0-0.5in.Resolution: 0.001in.Bezel diameter: 58mm.
Faithfull Letter punches are used for hand marking metals and other hard materials. They are useful for stamping personal identification or post codes on tools, cycles etc., as frequently recommended by police and insurers. The letter sizes as shown, relate to the height of the characters. The punches are manufactured from high quality tested carbon steel with double induction hardened heads to ensure high quality impressions. The body is hardened and the head is tempered to prevent chipping when hammered. Each set contains twenty seven punches with the characters & and A to Z.Set supplied in plastic box.Size : 2mm (5/64 in).
The BlueSpot Tools Drill & Tap Set is manufactured from hardened steel for increased hardness and a clean thread. Includes a range of common tap sizes and the drill bit required for that size of thread. Suitable for use with plastics (use distilled water as coolant), steel, aluminium and other non-ferrous metals. Supplied in a metal tin for easy access and storage. Contains: 7 x Drills: 2.5, 3.3, 4.2, 5, 6.8, 8.5, 10.2mm7 x Taps: M3, M4, M5, M6, M8, M10, M121 x Tap Wrench
These Faithfull punches are made from uniformly heat treated carbon steel and are used for removing pins in parallel holes. The removal of the pins should first be started with a hand or taper punch to avoid damage to the end of the parallel punch.Tip Diameter: 5mm (3/16in).Length: 100mm (4in).
Recoil Inserts are made from high quality stainless steel wire, with a diamond shaped cross section wound to the shape of a spring thread. The insert, which is larger in diameter than the tapped hole, is compressed during installation then allowed to spring back permanently anchoring the insert in the tapped hole. Because of its larger diameter the recoil insert has a greater contact area and is normally stronger than the original thread.Size. M3.0 x 0.50 Pitch.Length. 2 x Diameter
The Faithfull HSS Straight Flute Split Dies are versatile, general-purpose dies for threading rods. They are suitable for most materials and can be used for hand or machine cutting. Each die threads a male thread to its equal and opposite female thread. All dies should be used with the corresponding rod size to ensure both cutting ease and thread efficiency. These dies are made from high-speed steel with a bright finish and conform to ISO529.Size: M3Thread: 0.5
This compact set of engineering tools contains 6 essential marking and measuring tools. Supplied in a wooden storage case, the set contains the following tools: Faithfull FAIESMEASURE Engineers Marking & Measuring Set 6 Piece comprises:3 x Precision Stainless Steel Squares 50mm (2in), 100mm (4in), 150mm (6in), accurate to BS939 Grade B standard.1 x Steel Centre Finder 38mm capacity.1 x Stainless Steel Rule 150mm (6in).1 x Scriber 135mm (5¼in).
The Faithfull useful set of picks and hooks manufactured from stainless steel. The set contains 3 single end picks and 3 double end hooks. Suitable for pin or clip picking and the removal of seals and O-rings and many other applications. Approximate lengths 140mm - 165mm. Supplied in a plastic pouch.
Workpieces with straight edges, shoulders, grooves, studs, dowels, centre points and scribed lines can all be quickly and accurately located with this handy tool. Made of tool steel, hardened, ground and lapped.Description: Single end Body diameter: 0.375 Inch Contact diameter: 0.200 Inch
Starrett's popular precision External Micrometer is furnished with ratchet stop, lock nut and carbide measuring faces. Rigid one piece steel frame, ribbed for extra strength and tapered for use in narrow slots. Features Starrett's satin chrome finish for no glare and rust resistance.The Starrett 436.1MXRL-50 Outside Micrometer has the following specification: Size: 25-50mm.Graduation: 0.01mm.
The Wiha Screw Extractor Set 16 Piece are for thread-conserving removal of damaged or broken-off screws with left-hand or right-hand thread, particularly stripped hex screws. Simply hammer in the extractor, position the ring spanner to the bottom and screw out without tilting.Supplied in a handy carry case. Contains the following: 8 x Screw Extractor Drill Bits: 2.3, 2.8, 3.4, 4.5, 5.7, 6.8, 9.0 & 11.0mm. 8 x Screw Extractors: 2.0, 2.5, 3.0, 4.0, 5.0, 6.0, 8.0 & 10mm.
A quick and easy way to cut clean metric sized holes in sheet metal up to 16 gauge. The special design allows even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches are sold singly without key, which should be ordered separately. Thread the punch onto the hexagonal screw and then pass the hexagonal screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting hexagonal screw until it touches the metal sheet. Use a hexagonal key to turn the hexagonal screw. The screw will pull the punch through the metal and a hole will result. Please note these instructions apply to cutters up to 15 mm in size, for cutters 15 mm and over have a different configuration. Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.Size.65.0mm.Key Type.ME. 14mm hexagonal wrench
A quick and easy way to cut clean metric sized holes in sheet metal up to 16 gauge. The special design allows even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches are sold singly without key, which should be ordered separately. Thread the punch onto the hexagonal screw and then pass the hexagonal screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting hexagonal screw until it touches the metal sheet. Use a hexagonal key to turn the hexagonal screw. The screw will pull the punch through the metal and a hole will result. Please note these instructions apply to cutters up to 15 mm in size, for cutters 15 mm and over have a different configuration. Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.Size.51.0mm.Key Type.MC. 10mm hexagonal wrench
This 5 piece set of Screw Extractors is supplied in a handy storage case. The extractors allow quick and easy extraction of broken screws, pipes and stud bolts. To fit drill sizes: 7/64 inch, 9/64 inch, 5/32 inch, 1/4 inch and 19/64in.
A Recoil Tap is used when an existing thread has been damaged or stripped. The tap will form a thread slightly oversize the specified thread size.Size.M6 x 1.00 Pitch.Intermediate
The Faithfull three piece set of hand tap wrenches designed for use in hand tapping and reaming operations. Each wrench features a heavy-duty ductile steel body with a knurled chuck cap. A four point clamping system helps to increase the range of tap sizes that can be used and provide a firm non slip grip for accurate control.Three sizes cover the following metric and imperial size taps:M1-M4 1/16in - 5/32inM4-M6 5/32in - 1/4inM6-M12 1/4in - 1/2in
The Faithfull Prestige Centre Finder Gauge is manufactured from aluminium using computer numerical controlled (CNC) machines. The black anodised finish offers enhanced corrosion protection and the laser engraved scales give outstanding measurement accuracy. The centre finder is used to find the centre point of a square or cylindrical object. It features ruled markings in millimetre increments and can also be used for 45° and 90° mitre cut lines, making this product ideal for any engineer's workshop.With a measuring capacity of 90mm, this tool can be used on objects with a diameter or width of up to 180mm. Specification: Size: 100mmMeasuring Capacity: 90mm
Nail punches are designed to drive nail heads below the surface of the wood. Square head provides a large striking area which also stops the punch from rolling off the bench. Knurled body with hardened, slightly cupped head.Size. 1/16 in.Length 4 in
Letter punches are for marking metals and other solid materials. Produced from quality steel, heat treated to give maximum endurance and accuracy of impression. Packed in attractive plastic box.Size. 8mm (5/16 in)Contents A to Z Plus & (and)
Manufactured from heat-treated tool steel, this dual function tool is used firstly to set the rivet up and then to form the head.Size 4 x 125mm (5/32 x 5 in).
