Nail punches are designed to drive nail heads below the surface of the wood. Square head provides a large striking area which also stops the punch from rolling off the bench. Knurled body with hardened, slightly cupped head.Size. 1/32 in.Length 4 in
Nail punches are designed to drive nail heads below the surface of the wood. Square head provides a large striking area which also stops the punch from rolling off the bench. Knurled body with hardened, slightly cupped head.Size. 3/16 in.Length 4 in
The Moore & Wright Engineer's Levels have a precision ground cast base with a V-groove for location on cylindrical work. Each level is fitted with a main, cross and plumb vial and the main vial is protected by a rotating shroud. The solution in the vials maintains colour and fluidity under all workshop conditions and the main vial has a sensitivity of 1 minute.The Moore & Wright ELS Engineer's Levels have the following specification: Length: 165mm (6.5in).Width: 34mm (1.34in).Height: 46mm (1.81in).Resolution: 0.3mm per metre (0.0035in per foot).
The Moore & Wright Water Resistant Series Digital Caliper are fitted with a patented ceramic capacitive sensor and a large LCD display that offers 4 way measurement (mm/inch, absolute/incremental measurement). They can be zeroed at any point on the scale and is fitted with a conveniently located on/off switch. The calipers are manufactured to DIN 862 standards and water and dust resistant to IP54 specifications. Supplied with a CR2032 battery. Specification Range: 0-150mm (0-6in).Resolution: 0.01mm (0.005in).Jaws: 40mm.
The Moore & Wright Spring Dividers are manufactured from polished tool steel and the points are hardened to over 550Hv. The bow spring ensures uniform tension over working range and they are fitted with a centrally mounted adjustment screw. These Spring Dividers comply with BS3123 standards. Note: The nominal size is the distance between the centre of the roller and the working ends of the legs.The Moore & Wright 503 Spring Dividers have the following specifications: Size: 75mm (3in).
A quick and easy way to cut clean square holes in sheet metal up to 16 gauge. The special design allows an even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.All punches boxed singly without key, which should be ordered separately. Size.1in. Square.Key Type. B Key Operated. 5/16in AF
A quick and easy way to cut clean imperial sized holes in sheet metal up to 16 gauge. The special design allows an even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches boxed singly without key, which should be ordered separately. To use these punches they require a hole to be drilled through the sheet metal (large enough to clear the heagonal Screw) then the Die and hexagonal screw are threaded through the sheet metal then onto the die nut and screw die nut. When the hexagonal screw is tightened the punch will cut cleanly and evenly through the metal.Size. 1 1/2 in.Key Type.B. 5/16 in hexagonal wrench
Square Leg Compasses, when fitted with a standard pencil or other marking implement, can be used for drawing circles and arcs or used as dividers to measure distances or repeat a set distance. Manufactured from forged steel with square section legs for grip and balance, this Faithfull divider has a hardened and ground compass point and knurled grip locking screws. Size: 200mm (8in).
The Moore & Wright 100 Series Vernier Calipers have a standard workshop model design. They are made of hardened alloyed stainless steel and have a chromed scale with engraved graduations. The calipers allow 4-way measurement and the measuring surface is micro-lapped. The calipers are manufactured to DIN 862 standards. Supplied in a plastic box.The MAW10030BI calipers have the following specifications: Range: 0-300mm (0-12in).Resolution: 0.02mm (0.001in).
Feeler strips are widely used in automotive, aviation, diesel and farm equipment manufacture and service. Also used in jig, fixture and gauge work. Packed individually in an envelope. Length: 300mm (12in).Inch Gauge 12 in long Thickness: 0.001 in
SB-373N series parallel pin punches made from vanadium extra steel with a hexagonal shank. Fully polished steel surfaces and a brilliant chrome finish.Length: 150mm (6 in).Size: 8mm (5/16 in).
Hardened steel punches carefully heat treated for long life. Precisely knurled body with square head which gives a good striking area and prevents the punch from rolling.Size 3mm (1/8 in).Length 100mm (4 in)
Hardened steel punches carefully heat treated for long life. Precisely knurled body with square head which gives a good striking area and prevents the punch from rolling.Size 5mm (3/16 in).Length 100mm (4 in)
Manufactured from heat-treated tool steel, this dual function tool is used firstly to set the rivet up and then to form the head.Size 6.5 x 140mm (1/4 x 5 1/2 in)
Straight edge for accurate marking out with a carpenters pencil or metal scriber. Accuracy is 0.01% of the length of the straight edge.Size: 300 x 53mm (12 x 2.08in).
Metric 333mm lengths of high carbon bright steel, precision ground to very close tolerances; Above 25mm + - 0.025mm.Below 25mm + - 0.0127mm. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 14mm
Metric 333mm lengths of high carbon bright steel, precision ground to very close tolerances; Above 25mm + - 0.025mm.Below 25mm + - 0.0127mm. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 3mm
Metric 333mm lengths of high carbon bright steel, precision ground to very close tolerances; Above 25mm + - 0.025mm.Below 25mm + - 0.0127mm. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 25mm
Metric 333mm lengths of high carbon bright steel, precision ground to very close tolerances; Above 25mm + - 0.025mm.Below 25mm + - 0.0127mm. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 22mm
Imperial 13in lengths of high carbon bright steel, precision ground to very close tolerances; Above 1 in + - 0.0005in.Below 1 in + - 0.00025in. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 1 in
Metric 333mm lengths of high carbon bright steel, precision ground to very close tolerances; Above 25mm + - 0.025mm.Below 25mm + - 0.0127mm. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 16mm
Imperial 13in lengths of high carbon bright steel, precision ground to very close tolerances; Above 1 in + - 0.0005in.Below 1 in + - 0.00025in. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 3/4 in
1 x Moore & Wright 4009 Engineer's Square Grade B 225mm (9in)in Retail Packaging. Specifications: Blade Size: 273.1 x 38.1mm.Stock Size: 139.7 x 38.1mm.Inner Working: 107.9 x 234.95mm.
A quick and easy way to cut clean metric sized holes in sheet metal up to 16 gauge. The special design allows even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches are sold singly without key, which should be ordered separately. Thread the punch onto the hexagonal screw and then pass the hexagonal screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting hexagonal screw until it touches the metal sheet. Use a hexagonal key to turn the hexagonal screw. The screw will pull the punch through the metal and a hole will result. Please note these instructions apply to cutters up to 15 mm in size, for cutters 15 mm and over have a different configuration. Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.Size.64.0mm.Key Type.ME. 14mm hexagonal wrench
A quick and easy way to cut clean metric sized holes in sheet metal up to 16 gauge. The special design allows even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches are sold singly without key, which should be ordered separately. Thread the punch onto the hexagonal screw and then pass the hexagonal screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting hexagonal screw until it touches the metal sheet. Use a hexagonal key to turn the hexagonal screw. The screw will pull the punch through the metal and a hole will result. Please note these instructions apply to cutters up to 15 mm in size, for cutters 15 mm and over have a different configuration. Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.Size.20.0mm.Key Type.MB. 8mm hexagonal wrench
A quick and easy way to cut clean metric sized holes in sheet metal up to 16 gauge. The special design allows even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches are sold singly without key, which should be ordered separately. Thread the punch onto the hexagonal screw and then pass the hexagonal screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting hexagonal screw until it touches the metal sheet. Use a hexagonal key to turn the hexagonal screw. The screw will pull the punch through the metal and a hole will result. Please note these instructions apply to cutters up to 15 mm in size, for cutters 15 mm and over have a different configuration. Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.Size.31.0mm.Key Type.MB. 8mm hexagonal wrench
Type 117 Centre punches are manufactured from specially selected steel, hardened and properly tempered. They are well proportioned, nicely finished and have a knurled finger grip. The points are ground at the proper angle to give maximum service, and the tips are accurately centered. Length: 100mm (4in).Size 2 x 100mm (5/64 x 4 in)
Used to adjust tappets, spark plugs, distributor points, checking bearing clearances and gear play, fitting pistons, rings and pins and gauging narrow slots. Leaves are tempered steel, easily removed and replaced. Locking device on all sets.Inch Reading Gauges with Straight leaves 1/2 x 4 1/2 in No. of leaves: 13 Range: 0.0015 - 0.200 Inch (0.0015, 0.002, 0.003, 0.004, 0.006, 0.008, 0.010 to 0.040 by 0.01 in steps , 0.075, 0.100, 0.200 in).
Recoil Inserts are made from high quality stainless steel wire, with a diamond shaped cross section wound to the shape of a spring thread. The insert, which is larger in diameter than the tapped hole, is compressed during installation then allowed to spring back permanently anchoring the insert in the tapped hole. Because of its larger diameter the recoil insert has a greater contact area and is normally stronger than the original thread.Size. M4.0 x 0.70 Pitch.Length. 1 1/2 X Diameter
Recoil inserts are the quick and easy way to repair damaged threads or creating stronger original threads in alloys and composite materials in original equipment manufacture.Made from corrosion resistant stainless steel, they create stronger threads in most materials and simplifiy changeover from unified to metric or vice versa.They reduce thread wear and are interchangeable with other brands of inserts or tooling.Size. 5/16 UNC X 18 TPILength. 1 1/2 x Diameter.
Faithfull Letter and number punches are used for hand marking metals and other hard materials. They are useful for stamping personal identification or post codes on tools, cycles etc., as frequently recommended by police and insurers. The letter or number sizes as shown, relate to the height of the characters. The punches are manufactured from high quality tested carbon steel with double induction hardened heads to ensure high quality impressions. The body is hardened and the head is tempered to prevent chipping when hammered.Contents : 1, 2, 3, 4, 5, 6, 7, 8, 9, 0 (9 is achieved by reversing 6).Set supplied in plastic box.Size : 3mm (1/8 in).
1 x Moore & Wright 40012 Engineer's Square Grade B 300mm (12in) in Retail Packaging. Specification: Blade Size: 355.6 x 44.4mmStock Size: 177.8 x 44.4mmInner Working: 139.7 x 311.2mm
Straight edge for accurate marking out with a carpenters pencil or metal scriber. Accuracy is 0.01% of the length of the straight edge.Size: 450 x 53mm (18 x 2.08in).
These Dormer 2 piece sets each feature a tap and its corresponding pre-hole drill in one convenient package, helping to save time and error.The packs contain an A002 split-point jobber drill and a straight flute tap. The taps are suitable for threading up to 1.5x their diameter in most materials (ISO Standard). Two tap options are available: Second tap for through drilling, or a bottoming tap for blind holes.Specifications: Tap Type: SecondThread Size: M8
