Recoil Inserts are made from high quality stainless steel wire, with a diamond shaped cross section wound to the shape of a spring thread. The insert, which is larger in diameter than the tapped hole, is compressed during installation then allowed to spring back permanently anchoring the insert in the tapped hole. Because of its larger diameter the recoil insert has a greater contact area and is normally stronger than the original thread.Size. M12 x 1.75 Pitch.Length. 1 1/2 x Diameter
Recoil Inserts are made from high quality stainless steel wire, with a diamond shaped cross section wound to the shape of a spring thread. The insert, which is larger in diameter than the tapped hole, is compressed during installation then allowed to spring back permanently anchoring the insert in the tapped hole. Because of its larger diameter the recoil insert has a greater contact area and is normally stronger than the original thread.Size. M6.0 x 1.00 Pitch.Length. 1 x Diameter
Recoil Inserts are made from high quality stainless steel wire, with a diamond shaped cross section wound to the shape of a spring thread. The insert, which is larger in diameter than the tapped hole, is compressed during installation then allowed to spring back permanently anchoring the insert in the tapped hole. Because of its larger diameter the recoil insert has a greater contact area and is normally stronger than the original thread.Size. M8 x 1.25 Pitch.Length. 1 x Diameter
Recoil Inserts are made from high quality stainless steel wire, with a diamond shaped cross section wound to the shape of a spring thread. The insert, which is larger in diameter than the tapped hole, is compressed during installation then allowed to spring back permanently anchoring the insert in the tapped hole. Because of its larger diameter the recoil insert has a greater contact area and is normally stronger than the original thread.Size M8 x 1.25 Pitch.Length. 1 1/2 X Diameter
These Faithfull punches are made from uniformly heat treated carbon steel and are used for removing pins in parallel holes. The removal of the pins should first be started with a hand or taper punch to avoid damage to the end of the parallel punch.Tip Diameter: 2.5mm (3/32in).Length: 100mm (4in).
A Recoil Tap is used when an existing thread has been damaged or stripped. The tap will form a thread slightly oversize the specified thread size.Size.M8 x 1.25 Pitch.Intermediate
Recoil inserts are the quick and easy way to repair damaged threads or creating stronger original threads in alloys and composite materials in original equipment manufacture.Made from corrosion resistant stainless steel, they create stronger threads in most materials and simplifiy changeover from unified to metric or vice versa.Recoil thread repair kits contain a quality HSS tap, Installation tool, precision stainless steel inserts and instructions. Supplied in a sturdy container.
Wad punches are used for cutting holes in soft materials or for producing discs from the material being cut.One piece forging with ground and polished tapered section.Size 25mm (1 in)
Imperial 13in lengths of high carbon bright steel, precision ground to very close tolerances; Above 1 in + - 0.0005in.Below 1 in + - 0.00025in. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 5/8 in
Recoil inserts are the quick and easy way to repair damaged threads or creating stronger original threads in alloys and composite materials in original equipment manufacture.Made from corrosion resistant stainless steel, they create stronger threads in most materials and simplifiy changeover from unified to metric or vice versa. Recoil thread repair kits contain a quality HSS tap, Installation tool, precision stainless steel inserts and instructions.Supplied in a sturdy container.Please note NOT supplied with a tapping drill.Kit 14.0mm x 1.25Length 1 1/2 and 1 x Diameter
Faithfull ratcheting tap wrench precisely constructed with an ergonomically designed sliding 'T' handle for fitting into tight spaces with ease. The ratchet can be set for right or left hand operations or fixed in the neutral position.The Faithfull FAITWRM6M10 has the following specifications:Tap size capacity: M6 - M10
Pin vices are chiefly used for holding small taps, reamers, scribers or wire. The handles are tubular which permit holding wires of any length or diameter up through the length of the tool.Size: 1Capacity: 0 - 1mm (0 - 3/64 in)
The Faithfull Double Ended Scriber is a dual use scriber has a knife edge at one end and is pointed at the opposite end. The knife edge is ideal for scoring wood, plastics and laminates. It is also called a striking knife. Length: 165mm (6.1/2in).
Faithfull Centre punch with a square head which provides a larger striking area and prevents the punch rolling when laid on the bench. Carefully hardened and tempered and with a 90° ground point.Point Diameter: 4.0mm (5/32 in)Length: 100mm (4 in)
The Facom 249.G sheathed drift punches are tough and durable. With very high tensile strength, these punches feature a head hardened to 43 HRc and a long shank hardened to 58 HRc. The handles are ergonomically shaped for comfort and shock absorption. Ideal as an aid in aligning bolt or rivet holes prior to inserting a fastener.The FCM249G4Point diameter: 3.95mm.Length: 190mm.
Dormer E500 straight flute taps are the only type of taps that can be used by hand, but they may also be used in a machine if required. Extremely versatile, can tap through or blind holes in most materials. When tapping blind holes straight flute taps should be used in sets. The three taps which form a set are known by more than one name. 1. Taper or First tap2. Second or Intermediate tap3. Bottoming, third or plug tap. Metric coarse straight flute taps. Tolerance: Class 2 for 6H FitSurface treatment: BrightMaterial: HSS High Speed SteelChamfer No: 1,2 and 3, Serial no 4 and 5Flute Geometry: Straight Flutes ISO529Size 8.0mm x 1.25 bottoming
Dormer E500 straight flute taps are the only type of taps that can be used by hand, but they may also be used in a machine if required. Extremely versatile, can tap through or blind holes in most materials. When tapping blind holes straight flute taps should be used in sets. The three taps which form a set are known by more than one name. 1. Taper or First tap2. Second or Intermediate tap3. Bottoming, third or plug tap. Metric coarse straight flute taps. Tolerance: Class 2 for 6H FitSurface treatment: BrightMaterial: HSS High Speed SteelChamfer No: 1,2 and 3, Serial no 4 and 5Flute Geometry: Straight Flutes ISO529Size 6.0mm x 1.0 bottoming
The Moore & Wright CSM Precision Sets are supplied with a rule (graduated both sides), Protractor head, Square head and Centre head. The datum faces are fully hardened and ground to resist wear. There is a centrally mounted protractor vial allows unrestricted viewing and the protractor has full 360° scale plate, graduated 0° - 180° - 0°. The protractor is also fitted with a satin chrome scale plate. The precision rules have been fully hardened and tempered with deeply etched graduations on both sides for ease of reading and long life. It has a unique rule clamp that allows positive location and clamping and a clipped corner on rule to maximise capability Square Head offers the following fixed angles: 15°, 30°, 45°, 60°, 75° and 90°. Centre Head offers a fixed 90° angle, for finding the centre of round bar stock up to 120mm diameter. MAWCSRM600 & MAWCSRME24 are rules specifically designed for use with the Combination Sets (MAWCSM300 & MAWCSME12).The Moore & Wright CSM300 Precision Combination Set is a full set including 300mm rule (graduated both sides), Protractor head, Square head and Centre head. Measurements: mm and 0.5mm on both sides; numbered every 10mm.
Q.Max Thrust Races are recommended to increase punch life and to significantly ease the operation of the punch. Makes cutting the holes effortless.This 12mm Thrust Race is suitable for 32.5-51mm punches.
A quick and easy way to cut clean imperial sized holes in sheet metal up to 16 gauge. The special design allows an even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches boxed singly without key, which should be ordered separately. To use these punches they require a hole to be drilled through the sheet metal (large enough to clear the heagonal Screw) then the Die and hexagonal screw are threaded through the sheet metal then onto the die nut and screw die nut. When the hexagonal screw is tightened the punch will cut cleanly and evenly through the metal.Size. 1 5/8 in.Key Type.B. 5/16 in hexagonal wrench
A quick and easy way to cut clean metric sized holes in sheet metal up to 16 gauge. The special design allows even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches are sold singly without key, which should be ordered separately. Thread the punch onto the hexagonal screw and then pass the hexagonal screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting hexagonal screw until it touches the metal sheet. Use a hexagonal key to turn the hexagonal screw. The screw will pull the punch through the metal and a hole will result. Please note these instructions apply to cutters up to 15 mm in size, for cutters 15 mm and over have a different configuration. Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.Size.48.0mm.Key Type. MC. 10mm hexagonal wrench
A quick and easy way to cut clean metric sized holes in sheet metal up to 16 gauge. The special design allows even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches are sold singly without key, which should be ordered separately. Thread the punch onto the hexagonal screw and then pass the hexagonal screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting hexagonal screw until it touches the metal sheet. Use a hexagonal key to turn the hexagonal screw. The screw will pull the punch through the metal and a hole will result. Please note these instructions apply to cutters up to 15 mm in size, for cutters 15 mm and over have a different configuration. Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.Size.37.0mm.Key Type.MC. 10mm hexagonal wrench
Starrett's popular precision External Micrometer is furnished with ratchet stop, lock nut and carbide measuring faces. Rigid one piece steel frame, ribbed for extra strength and tapered for use in narrow slots. Features Starrett's satin chrome finish for no glare and rust resistance.The Starrett 436.1MXRL-75 Outside Micrometer has the following specification: Size: 50-75mm.Graduation: 0.01mm.
A comfortable DynaGrip sleeve surrounds a fully hardened body, which is precision milled for extra long life. The overall length is 25% longer than conventional nail punches, making it easy to set nails in hidden and hard to reach areas. Colour coded sleeves for easier identification of sizes.Tip Size: 1/32inLength: 5inColour. Yellow Sleeve
Recoil Inserts are made from high quality stainless steel wire, with a diamond shaped cross section wound to the shape of a spring thread. The insert, which is larger in diameter than the tapped hole, is compressed during installation then allowed to spring back permanently anchoring the insert in the tapped hole. Because of its larger diameter the recoil insert has a greater contact area and is normally stronger than the original thread.Size. M8 x 1.25 Pitch.Length. 2 x Diameter
Metric 333mm lengths of high carbon bright steel, precision ground to very close tolerances; Above 25mm + - 0.025mm.Below 25mm + - 0.0127mm. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 8mm
Dormer E500 straight flute taps are the only type of taps that can be used by hand, but they may also be used in a machine if required. Extremely versatile, can tap through or blind holes in most materials. When tapping blind holes straight flute taps should be used in sets. The three taps which form a set are known by more than one name. 1. Taper or First tap2. Second or Intermediate tap3. Bottoming, third or plug tap. Metric coarse straight flute taps. Tolerance: Class 2 for 6H FitSurface treatment: BrightMaterial: HSS High Speed SteelChamfer No: 1,2 and 3, Serial no 4 and 5Flute Geometry: Straight Flutes ISO529Size 4.0mm x 0.7 bottoming
Dormer Dienuts are used to reclaim worn or damaged threads in most materials. Metric Coarse Dienuts. Application: For reclamation of screw threads. Also available in MF, UNC, G(BSPF) thread forms. Tolerance: 6g.Chamfer Lead: Two Threads.Surface treatment: Bright.Material: HSS - High Speed Steel. BS1127:1950Size: 10mm x 1.50.
Letter punches are for marking metals and other solid materials. Produced from quality steel, heat treated to give maximum endurance and accuracy of impression. Packed in attractive plastic box.Size. 4mm (5/32 in)
The Halls High-Speed Steel Deburring Smooth Cutter, ideal for deburring and chamfering pre-drilled holes in a wide range of materials. Optimum performance is obtained on aluminium and other soft alloys. Shank: 1/4in Hexagon.Diameter of cut 5 -13mm (13/64 - 33/64 in)
The Moore & Wright 200 Series Digital External Micrometer has a tapered design that provides easier access to difficult areas and a hammertone finished frame with a high quality insulated grip. It also has tungsten carbide measuring faces and a constant force ratchet on the thimble. The large LCD display allows for 4 types of measurement (mm/inch conversion and Absolute/Incremental reading) and a zero setting. The micrometers are manufactured to DIN 863 standards. Specification Range: 0-25mm/0-1in.Resolution: 0.001mm/.00005in.
The Faithfull Button Magnets are made from alnico to provide a high resistance to corrosion and operate in high temperatures up to 500°C. The north and south poles are on the same face and separated by a slot. All sizes have holes for mounting the magnet, but they must not be recessed into ferrous metals, as it will short circuit the magnetism. Suitable to be used as work holding devices for welding, sign making and other applications, or for reed switch operation.Diameter: 19.0mmHeight: 12.7mmPull Power: 1.8kg
Faithfull Letter and number punches are used for hand marking metals and other hard materials. They are useful for stamping personal identification or post codes on tools, cycles etc., as frequently recommended by police and insurers. The letter or number sizes as shown, relate to the height of the characters. The punches are manufactured from high quality tested carbon steel with double induction hardened heads to ensure high quality impressions. The body is hardened and the head is tempered to prevent chipping when hammered.Contents : 1, 2, 3, 4, 5, 6, 7, 8, 9, 0 (9 is achieved by reversing 6).Set supplied in plastic box.Size : 8mm (5/16 in).
SB-373N series parallel pin punches made from vanadium extra steel with a hexagonal shank. Fully polished steel surfaces and a brilliant chrome finish.Length: 150mm (6 in).Size: 2mm (5/64 in)
These Faithfull punches are made from uniformly heat treated carbon steel and are used for removing pins in parallel holes. The removal of the pins should first be started with a hand or taper punch to avoid damage to the end of the parallel punch.Tip Diameter: 1.5mm (1/16in).Length: 100mm (4in).
