Bondloc B2001 is a hand kneadable, specialty epoxy putty that mixes in 1 minute for permanent repairs to many substrates. Contains fading black dye that becomes grey after mixing. May be applied under water (fresh or salt). Bonds to fibreglass, metal, wood, concrete and glass. Will not yellow to UV exposure. Hardens in 10 minutes, back in service in an hour, full strength in 24 hours. Can be used for repairing tanks and drums, patching holes in pipes, stopping leaks and repairing porosity holes in castings. Specification: Typical Properties: 7 days cured at 24°CColour: Black, changes to grey after mixingViscosity: putty/hand kneadablePot Life @24°C: 20 minutesComprehensive Strength: 83 N/mm2Adhesive Tensile Shear: 5 N/mm2Cured Hardness Shore: D 75Dielectric Strength: volts/mil 300Solids: 100%Temperature Resistance: Wet: 49°C, Dry: 121°CSize: 50g
Bondloc B2012 is a 2-part, rapid cold curing epoxy adhesive, that is suitable for bonding a wide variety of surfaces including steel, aluminium and galvanised iron. Reacts within a few minutes to give a tough, resilient bond on a wide variety of surfaces. Specifications: Mix Ratio: 1:1Work Life: As a mix: 4 1/2 - 5 minutesSize: 25ml Part 1 Physical Form: Viscous liquidChemical Type: EpoxyAppearance: ClearViscosity 25°C: 100 poiseSpecific Gravity: 1.17 Part 2 Physical Form: Viscous liquidChemical Type: Mercaptan and PolyamideAppearance: ClearViscosity 25°C: 130 poiseSpecific Gravity: 1.14
Bondloc B2060 is a 60 second, 2-part, rapid cold curing epoxy adhesive. It is suitable for bonding a wide variety of surfaces including steel, aluminium and galvanised iron. It reacts within a minute to give a tough resilient bond on a wide variety of surfaces. Specifications: Mix Ratio 1:1Work Life as a Mix: 40 - 70 secondsSize: 25ml Part 1 Physical Form: Viscous liquidChemical Type: EpoxyAppearance: ClearViscosity @ 25°C: 100 poiseSpecific Gravity: 1.17 Part 2 Physical Form: Viscous liquidChemical Type: Mercaptan and PolyamideAppearance: BlueViscosity @ 25°C: 130 PoiseSpecific Gravity: 1.14
Bondloc B222 Screwlock is a Thixotropic anaerobic threadlocker of low strength designed for easy disassembly of treated components. B222’s Anaerobic nature allows it to cure only when confined between metal parts. Applications include all small fasteners, where vibration loosening prevention and non-leakage through threaded fastening is required. Ideal on small set screws, brass and most types of small threaded nuts, bolts, screws, hex and slot driven components including keyed fasteners etc. Specifications: Resin: DimethacrylateColour: Purple White tintCure speed with Activator: <15 mins @ 20°CCure speed without Activator: 15 minutesViscosity- Brookfield Sp3 @ 20rpm: 1200 cps (thixo), Sp3 @ 20rpm: 5000cpsGap Fill/Max Threadform: 0.5mm/M36Flash Point: >100°CShelf Life: 12 months @ 20°CSpecific Gravity: 1.06 Cured performance: Full Cure Time: 12 hours @ 20°CTypical Strength: ISO 10964: 6Nm M10’sRange of Strength: Breakaway: 4Nm up to 12Nm, Prevailing: 2Nm up to 6 NmDIN 54454 Breakloose: 10Nm max 20NmDIN 54454 Prevailing: 6Nm up to 20NmBondloc Screwlock Low Strength Threadlocker Size: 10ml.
Bondloc B222 Screwlock is a Thixotropic anaerobic threadlocker of low strength designed for easy disassembly of treated components. B222’s Anaerobic nature allows it to cure only when confined between metal parts. Applications include all small fasteners, where vibration loosening prevention and non-leakage through threaded fastening is required. Ideal on small set screws, brass and most types of small threaded nuts, bolts, screws, hex and slot driven components including keyed fasteners etc. Specifications: Resin: DimethacrylateColour: Purple White tintCure speed with Activator: <15 mins @ 20°CCure speed without Activator: 15 minutesViscosity- Brookfield Sp3 @ 20rpm: 1200 cps (thixo), Sp3 @ 20rpm: 5000cpsGap Fill/Max Threadform: 0.5mm/M36Flash Point: >100°CShelf Life: 12 months @ 20°CSpecific Gravity: 1.06 Cured performance: Full Cure Time: 12 hours @ 20°CTypical Strength: ISO 10964: 6Nm M10’sRange of Strength: Breakaway: 4Nm up to 12Nm, Prevailing: 2Nm up to 6 NmDIN 54454 Breakloose: 10Nm max 20NmDIN 54454 Prevailing: 6Nm up to 20NmBondloc Screwlock Low Strength Threadlocker Size: 50ml.
Bondloc B243 is an Anaerobic formulation designed to be used on parts in an as received condition, such as those with protective films (oils) etc. Oil tolerant B243 is designed for direct application onto as received parts where a light oily film exists or where surrounding parts contamination is a problem in maintenance. Specifications: Resin: Mod MethacrylateColour: Blue ThixotropicCure speed: <15 mins @ 20°CViscosity: 1200-1800 thixotropicGap fill: 0.1mmFlash Point: >85°CShelf life: 12 months @ 20°CSpecific gravity: 1.04Max. Operating Temperature: -53°C to + 150°C Cured Performance: Full Cure Time: 24 hoursTypical Breakaway Strength: 12 N/mm²Typical Prevailing Strength: 8-10N/mm²Bondloc Nutlock Medium Strength Threadlocker Size: 10ml.
Bondloc B243 is an Anaerobic formulation designed to be used on parts in an as received condition, such as those with protective films (oils) etc. Oil tolerant B243 is designed for direct application onto as received parts where a light oily film exists or where surrounding parts contamination is a problem in maintenance. Specifications: Resin: Mod MethacrylateColour: Blue ThixotropicCure speed: <15 mins @ 20°CViscosity: 1200-1800 thixotropicGap fill: 0.1mmFlash Point: >85°CShelf life: 12 months @ 20°CSpecific gravity: 1.04Max. Operating Temperature: -53°C to + 150°C Cured Performance: Full Cure Time: 24 hoursTypical Breakaway Strength: 12 N/mm²Typical Prevailing Strength: 8-10N/mm²Bondloc Nutlock Medium Strength Threadlocker Size: 50ml.
Bondloc B270 Studlock is a permanent green coloured general-purpose adhesive for permanent threaded assemblies. B270 locks studs up to 1in, sealing against leakage and corrosion. It is chemical-resistant, resisting fuels, lubricants and most industrial liquids and gases. It eliminates double nutting and/or welding of critical assemblies. It also permits reduced casting thickness and ultimate lightness, reduced assembly stress and eliminates cracked castings due to interference fit stresses. Specifications: Resin: DimethacrylateColour: GreenFixture Speed No Activator: 10 min.Fixture Speed With Activator: 5 min. Viscosity: 500 cpsGap fill: 0.25mmFlash Point: >100°CShelf Life: minimum 12 monthSpecific Gravity: 1.06.Max Operating Temperature: -55°C to +180°C Cured Performance: Full Cure Time: 12 hours.Cure Time with good % of final strength: 2 hoursTypical Breakaway Strength DIN : 40 Nm (25/55)Typical Prevailing Strength DIN : 55 Nm (45/70)Typical Breakaway ISO 10964: 26 Nm (16/36)Typical Prevailing ISO 10964: 36 Nm (22/50)Bondloc Studlock High Strength Threadlocker Size: 10ml.
Bondloc B270 Studlock is a permanent green coloured general-purpose adhesive for permanent threaded assemblies. B270 locks studs up to 1in, sealing against leakage and corrosion. It is chemical-resistant, resisting fuels, lubricants and most industrial liquids and gases. It eliminates double nutting and/or welding of critical assemblies. It also permits reduced casting thickness and ultimate lightness, reduced assembly stress and eliminates cracked castings due to interference fit stresses. Specifications: Resin: DimethacrylateColour: GreenFixture Speed No Activator: 10 min.Fixture Speed With Activator: 5 min. Viscosity: 500 cpsGap fill: 0.25mmFlash Point: >100°CShelf Life: minimum 12 monthSpecific Gravity: 1.06.Max Operating Temperature: -55°C to +180°C Cured Performance: Full Cure Time: 12 hours.Cure Time with good % of final strength: 2 hoursTypical Breakaway Strength DIN : 40 Nm (25/55)Typical Prevailing Strength DIN : 55 Nm (45/70)Typical Breakaway ISO 10964: 26 Nm (16/36)Typical Prevailing ISO 10964: 36 Nm (22/50)Bondloc Studlock High Strength Threadlocker Size: 50ml.
Bondloc B3294 is a toughened structural adhesive formulated for bonding dissimilar substrates as well as unprepared metals, ceramics, wood, concrete and standard thermoset plastics. The final adhesive bond is designed to be load bearing and resistant to weathering, humidity and wide temperature variations. Outdoor weathering or solvent exposure thermoformed plastic assemblies, PVC, fibreglass, vinyls, ABS, steel aluminium, stainless steel, acrylics, phenolic, polycarbonate, styrenics, Noryl, PET, wood, concrete and ceramic magnet and speaker assembly. Specifications: Viscosity: 55,000cpsColour: Off whiteWeight: 8.44 lbs/galMixed Density: 8.28lbs/galFlash Point: 51°FMixed Viscosity: No sagging gelOpen Time: 3 minutes @ 72°F, 22°CAssembly Time: 6 minutes @ 72°F, 22°CFunctional Cure: 3/4-1 hourFull Cure: 4 hoursSolvents: NoneCoverage: (based on 25ml) 152 sq.in @ 0.010in
Bondloc B401 is a Medium Viscosity Cyanoacrylate. It bonds metals, plastics, wood, ceramics, rubber, leather, card, glass and many other materials. Cyanoacrylate adhesives cure through reaction with moisture held on the surface to be bonded. They need close fitting joints and usually solidify in seconds which has resulted in the universal generic name of 'superglues'. Curing is started by the film of moisture found on most surfaces which is usually slightly alkaline and it is this alkalinity which causes the polymerisation. Most grades have varying viscosities and therefore they need close fitting joints. Newer developments of gelled variants allow cure in wider gaps and application to vertical surfaces. Cyanoacrylates are suited to small plastic parts and to rubber bonding. Liquid Properties: Ester base: Ethyl cyanoacrylateAppearance: Clear, colourlessSpecific Gravity: 25°C 1.06 g/cm²Shelf life: 12 months unopenedViscosity @ 25°C: 90 - 120 Size: 20g
Bondloc B415 is a high viscosity Cyanoacrylate that bonds metals, plastics, wood, ceramics, rubber, leather, card, glass and many other materials. Cyanoacrylate adhesives cure through reaction with moisture held on the surface to be bonded. They need close fitting joints and usually solidify in seconds which has resulted in the universal generic name of 'superglues'. Curing is started by the film of moisture found on most surfaces which is usually slightly alkaline and it is this alkalinity which causes the polymerisation. Most grades have varying viscosities and therefore they need close fitting joints. Newer developments of gelled variants allow cure in wider gaps and application to vertical surfaces. Cyanoacrylates are suited to small plastic parts and to rubber bonding. Liquid Properties: Ester base: Ethyl cyanoacrylateAppearance: Clear, colourlessSpecific Gravity: 25°C 1.06 g/cm²Shelf life: 12 months unopenedViscosity @ 25°C: 1200 - 1800 Size: 20g
Bondloc B454 is a Thixotropic Non-Drip Gel Cyanoacrylate that bonds metals, plastics, wood, ceramics, rubber, leather, card, glass and many other materials. Cyanoacrylate adhesives cure through reaction with moisture held on the surface to be bonded. They need close fitting joints and usually solidify in seconds which has resulted in the universal generic name of 'Superglues'. Curing is started by the film of moisture found on most surfaces which is usually slightly alkaline and it is this alkalinity which causes the polymerisation. Most grades have varying viscosities and therefore they need close fitting joints. Newer developments of gelled variants allow cure in wider gaps and application to vertical surfaces. Cyanoacrylates are suited to small plastic parts and to rubber bonding. Liquid Properties:Ester base: Ethyl cyanoacrylateAppearance: Clear, colourlessSpecific Gravity: 25°C 1.1 g/cm²Shelf life: 12 months unopenedViscosity @ 25°C: GelSize: 20g
Bondloc B480 is a black rubber toughened Cyanoacrylate that bonds metals, plastics, wood, ceramics, rubber, leather, card, glass and many other materials. Cyanoacrylate adhesives cure through reaction with moisture held on the surface to be bonded. They need close fitting joints and usually solidify in seconds which has resulted in the universal generic name of 'Superglues'. Curing is started by the film of moisture found on most surfaces which is usually slightly alkaline and it is this alkalinity which causes the polymerisation. Most grades have varying viscosities and therefore they need close fitting joints. Newer developments of gelled variants allow cure in wider gaps and application to vertical surfaces. Cyanoacrylates are suited to small plastic parts and to rubber bonding. Liquid Properties:Ester base: Ethyl cyanoacrylateAppearance: Black Opaque LiquidSpecific Gravity: 25°C 1.06 g/cm²Shelf life: 6 months unopenedViscosity @ 25°C: 350 - 450 mPasSize: 20g
Bondloc Gasket Seal Type B518 is a Red, smooth, thick paste. Easily applied, cures once confined between the parts to form in place a tough, flexible gasket. Gives an instant low pressure seal. Used for fuel and water pumps, split crank cases on engines, gearbox covers, engine thermostats, air compressor end caps, engine timing cam covers onto blocks, pump couplings, fuel tanks on small implements, chain saws, lawn mowers etc. Use B518 for dressing gaskets, spacers etc. Specifications: Resin: Modified Urethane Acrylate.Colour: Red Paste.Fixture Speed No Activator: Up to 12 hours.Fixture Speed With Activator: <2 hours.Viscosity: >3,500,000 cps.Gap fill: 0.5 mm.Flash point: >100°C.Shelf life: 12 months @ 20°C.Specific gravity: 1.13.Max operating temp: -55°C to + 150°C. Cured Performance: Full Cure Time: 12 hours.Tensile strength: 8 N/mm(2).Static Shear strength: 12.5 N/mm(2). Size: 50ml.
Bondloc B542 Hydraulic Seal is a thixotropic liquid which cures anaerobically to form a tough, high pressure seal on all types of threaded couplings used on low, medium and high pressure lines. Used for all types of hydraulic connections, and sealing against typical pressure line ratings. Can also be used to fit valves, threaded couplings, adaptors, quick disconnect parts, compression fittings and vibration proofing joints. Specifications: Resin: Dimethacrylate.Colour: Brown.Fixture Speed No Activator: 10 - 20 mins. Fixture Speed With Activator: <5 mins. Spindle 2 @ 2.5 rpm: 1000 to 2750 cps.Spindle 2 @ 20rpm: 400 to 800 cps.Gap fill: 0.05mm to 0.25 mm.Flash point: >100°C.Shelf life: 2 Years @ 20°C.Specific gravity: 1.06.Max operating temp: -55°C to + 150°C. Cured Performance: Full Cure Time: 12 hours.Typical breakway ISO 10964: 15 N.m.Typical prevailing ISO 10964: >8 N.m.DIN 10964 Breakloose: 24 N.m.DIN 10964 Prevailing: 15 to 35 N.m.Typical Break and Prevailing: 20N.m/15N.m.Bondloc Hydraulic Seal Pneumatic Fittings. Size: 10ml.
Bondloc B542 Hydraulic Seal is a thixotropic liquid which cures anaerobically to form a tough, high pressure seal on all types of threaded couplings used on low, medium and high pressure lines. Used for all types of hydraulic connections, and sealing against typical pressure line ratings. Can also be used to fit valves, threaded couplings, adaptors, quick disconnect parts, compression fittings and vibration proofing joints. Specifications: Resin: Dimethacrylate.Colour: Brown.Fixture Speed No Activator: 10 - 20 mins. Fixture Speed With Activator: <5 mins. Spindle 2 @ 2.5 rpm: 1000 to 2750 cps.Spindle 2 @ 20rpm: 400 to 800 cps.Gap fill: 0.05mm to 0.25 mm.Flash point: >100°C.Shelf life: 2 Years @ 20°C.Specific gravity: 1.06.Max operating temp: -55°C to + 150°C. Cured Performance: Full Cure Time: 12 hours.Typical breakway ISO 10964: 15 N.m.Typical prevailing ISO 10964: >8 N.m.DIN 10964 Breakloose: 24 N.m.DIN 10964 Prevailing: 15 to 35 N.m.Typical Break and Prevailing: 20N.m/15N.m.Bondloc Hydraulic Seal Pneumatic Fittings. Size: 50ml.
Bondloc B572 White Pipe Seal is designed for the locking and sealing of metal pipes and fittings. The product cures when confined in the absence of air between close fitting metal surfaces and prevents loosening and leakage from shock and vibration. The thixotropic nature reduces the migration of liquid product after application to the substrate. Has a good chemical/solvent resistance to Ethanol, Motor Oil, Unleaded Petrol and Brake Fluid. B572 is unusual in that it does not fully cure until some 60 hours after application, allowing for re-alignment of elbows and joints. Replaces tapes and dopes, stops gas and fluid leaks on most metals and assists in lubricating during assembly. Will not shred or tear which would contaminate your system. Use it to seal against oils, gases, chemicals, water and steam etc. Specifications: Resin: Dimethacrylate.Colour: White paste.Cure speed with activator: Not recommended.Cure speed Without Activator: up to 60 hours.Viscosity Brookfield Sp3 @ 20rpm: 20,000cps.Gap fill / Max threadform: 0.4 mm / M36.Flash Point: >85°C.Shelf Life: 36 months @ 20°C. Specific Gravity: 1.25.Max Operating Temperature: -55°C to + 150°C. Cured Performance: Full Cure Time: 60 hours.Typical breakaway strength: 6 N.m.Typical prevailing strength: 2 N.m. Size: 50ml.
Bondloc B574 is an Instant Gasket material that forms in place, making almost any size and shape, replacing paper, cork etc. It eliminates relaxation and on loads loss. The assembled parts are usually suitable for immediate Low Pressure ( 6 bar) service and once cured can resist 350 Bar Pressure depending on gap size. Suitable for all formed in place applications such as gear box sealing, pump flanges, transmission assemblies, cover plates on tanks, cam shaft sealing, bearing gaps, outer housings, crank case and sump assemblies and flange pipe fittings. Specifications: Resin: Dimethacrylate.Colour: Orange paste.Cure speed with Activator: 10 mins.Cure speed without Activator: 15-30 mins.Viscosity - Brookfield Sp3 @ 20rpm: 50,000cps.Gap Fill/Max Threadform: 0.5mm/M36.Flash Point: >100°C.Shelf Life: 12 months @ 20°C.Specific Gravity: 1.10.Max operating temperature: -55°C to 150°C. Cured Performance: Full Cure Time: 24 hours @ 20°C.Breakloose Strength: 8N.m.Static Shear Strength: 10N.m. Size: 50ml.
Bondloc B577 Pipe Seal is a high viscosity thixotropic gel paste which cures rapidly, sealing instantly to 10 bar through its Anaerobic cure system in contact with metals in the absence of air (oxygen). When fully cured it resists pressure up to 350 bar. B577 is not suitable for oxygen systems. Good chemical/solvent resistance to Ethanol, Motor Oil, Unleaded Petrol, Acetone and Brake Fluid. Typical applications are in sealing of all types of threaded connections against water, oil, gases and most common materials conveyed by pipes. Specification: Resin: Dimethacrylate.Colour: Yellow.Cure Speed with Activator: <10 minutes.Cure Speed without Activator: <15 mins @ 20°C.Viscosity: >50,000 cps.Gap Fill: 0.05mm to 0.4mm.Flash Point: >100°C.Shelf Life: 12 months @ 20°C.Specific Gravity: 1.09.Max. Operating Temperature: +150°C. Cured Performance: Full Cure Time: 6-12 hours.Typical Breakaway Strength: >6 to <15 N/mm (2).Prevailing Torque: >3 to < 9 N/mm (2).Static Shear Strength: >5 to <15 N/mm (2). Size: 50ml.
Bondloc B603 is an anaerobic formulation designed for direct use on as received parts such as those with protective films. It is an Oil tolerant retainer and is designed for direct application onto as received parts where a light oily film exists or where surrounding parts contamination is a problem in maintenance. Specifications: Resin: Mod. Methacrylate.Colour: Green.Cure speed: <15 mins @ 20°C.Viscosity: 125 cps.Gap fill: 0.1mm.Flash point: >85°C.Shelf life: 12 months @ 20°C.Specific gravity: 1.04.Max operating temp: -53°C to +150°C. Cured Performance: Full Cure Time: 24 hours.Static shear (degreased): 28 N/mm².Static shear (oiled film): 21 - 24 N/mm². Size: 50ml.
Bondloc B638 Retainer is designed to give high strength retention under cyclic loading. It can retain its full strength and not suffer fatigue under load stress. It is a cylindrical parts supplement, suited to structural components such as cylindrical parts under dynamic load, keys, splines, even structural tubing with close tolerance fit. Specifications: Resin: Urethane Acrylate.Colour: Green.Fixture Speed No Activator: 5 mins.Fixture Speed With Activator: <5 mins.Viscosity: 2500 cps.Gap fill: 0.2mm.Flash Point: >85°C.Shelf Life: 12 months min.Specific Gravity: 1.08.Max Operating Temperature: -55°C to + 150°C. Cured Performance: Full Cure Time: 24 hours.Static shear strength: 30 N/mm².Bondloc high strength retaining Compound. Size: 10ml.
Bondloc B638 Retainer is designed to give high strength retention under cyclic loading. It can retain its full strength and not suffer fatigue under load stress. It is a cylindrical parts supplement, suited to structural components such as cylindrical parts under dynamic load, keys, splines, even structural tubing with close tolerance fit. Specifications: Resin: Urethane Acrylate.Colour: Green.Fixture Speed No Activator: 5 mins.Fixture Speed With Activator: <5 mins.Viscosity: 2500 cps.Gap fill: 0.2mm.Flash Point: >85°C.Shelf Life: 12 months min.Specific Gravity: 1.08.Max Operating Temperature: -55°C to + 150°C. Cured Performance: Full Cure Time: 24 hours.Static shear strength: 30 N/mm².Bondloc High Strength Retaining Compound. Size: 50ml.
Bondloc B641 is a single part anaerobic securing compound, designed for fitting cylindrical metal assemblies and cures when confined between the parts. It will secure all types and sizes of bearings, shafts and cylindrical parts which will require disassembly in the future. It is medium strength and is colour-coded yellow for job identification. Specifications: Resin: Mod. Dimethacrylate.Colour: Yellow. Fixture Speed No Activator: 10-15 mins.Fixture Speed With Activator: <5 mins. Viscosity: 400-800 cps.Gap fill: 0.2 mm. Flash Point: >100°C. Shelf Life: 12 month min.Specific Gravity: 1.06.Max Operating Temperature: -55°C to + 150°C. Cured Performance: Full Cure Time: 12 hours.Static shear strength: 12N/mm².ISO 10123 pin/collars range: 1-16 N/mm(²).Bondloc Bearing Fit Retaining Compound. Size: 10ml.
Bondloc B641 is a single part anaerobic securing compound, designed for fitting cylindrical metal assemblies and cures when confined between the parts. It will secure all types and sizes of bearings, shafts and cylindrical parts which will require disassembly in the future. It is medium strength and is colour-coded yellow for job identification. Specifications: Resin: Mod. Dimethacrylate.Colour: Yellow. Fixture Speed No Activator: 10-15 mins.Fixture Speed With Activator: <5 mins. Viscosity: 400-800 cps.Gap fill: 0.2 mm. Flash Point: >100°C. Shelf Life: 12 month min.Specific Gravity: 1.06.Max Operating Temperature: -55°C to + 150°C. Cured Performance: Full Cure Time: 12 hours.Static shear strength: 12N/mm².ISO 10123 pin/collars range: 1-16 N/mm(²).Bondloc Bearing Fit Retaining Compound. Size: 50ml.
This Bosch Twin Pack contains the following: 1 x 12V GSB 12V-15 Professional Combi Drill has the shortest design in its class for optimum handling. With a 2-speed planetary gearbox for powerful screwdriving and drilling applications in wood and metal, and impact drilling in masonry. No Load Speed: 0-380/0-1,300/min.Impact Rate: 19,500/bpmMax. Torque: 30Nm, Settings: 20 + 1 1 x 12V GDR 12V-105 Professional Impact Driver has an extremely compact design and is equipped with Bosch Electronic Cell Protection (ECP). This protects the battery against overload, overheating and total discharge. Bit Holder: 6.35mm (1/4in)No Load Speed: 0-2,600/min.Impact Rate: 0-3,100/bpmMax. Torque: 105NmCapacity: Screw Diameter: M4-M12 Also supplied with: 2 x 12V 2.0Ah Li-ion Batteries, 1 x 12V GAL 12V-20 Compact Charger and 1 x Tool Bag
This Bosch Twin Pack contains the following: 1 x 12V GSB 12V-15 Professional Combi Drill has the shortest design in its class for optimum handling. With a 2-speed planetary gearbox for powerful screwdriving and drilling applications in wood and metal, and impact drilling in masonry. No Load Speed: 0-380/0-1,300/min.Impact Rate: 19,500/bpm.Max. Torque: 30Nm, Settings: 20 1. 1 x 12V GDR 12V-105 Professional Impact Driver has an extremely compact design and is equipped with Bosch Electronic Cell Protection (ECP). This protects the battery against overload, overheating and total discharge. Bit Holder: 6.35mm (1/4in).No Load Speed: 0-2,600/min.Impact Rate: 0-3,100/bpm.Max. Torque: 105Nm.Capacity: Screw Diameter: M4-M12. Also supplied with: 2 x 12V 2.0Ah Li-ion Batteries, 1 x 12V GAL 12V-20 Compact Charger and 1 x Tool Bag.
The Bosch 0A00 L-BOXX Collapsible Hand Truck has a lightweight yet durable Aluminium construction. The base plate and elastic band enable you to safely transport L-BOXX elements. Its collapsible handle and wheels enable space-saving storage. Specifications: Load-bearing Capacity: Ground 12kg, Stairs 60kg.Dimensions (WxLxH): 490 x 790 x 80mm.Weight: 7.1kg.
The Bosch L-BOXX Carry Case is made from robust, durable ABS plastic. Fitted with a click mechanism that allows stacked boxes to be easily opened for convenient handling. They can be customised to carry various tools thanks to interchangeable tool inlays. Improved storage and transportation within the Bosch Mobility System.The Bosch 102 L-BOXX Carry Case has an additional front handle for carrying the box close to the body. Suitable for all types of power tools. Specification: Top Load Capacity: 100kgIn-box Load Capacity: 25kgOuter Dimensions (width x length x height): 442 x 357 x 117mmWeight: 1.8kg
The Bosch 102 L-BOXX Carry Case offers an improved storage and transportation solution in line with the Bosch Mobility System. Stacked boxes can be easily and conveniently opened with the improved L-BOXX click mechanism. Extensive compatibility of the L-BOXX variants, tool inlays, and the Sortimo in-vehicle system provides full flexibility. It has a robust design, manufactured from durable ABS plastic. Fitted with securely closing latches and a top handle, making it easy to carry. Compatible with the L-BOXX variants, tool inlays, the Sortimo in-vehicle system, Aluminium Caddy, and L-BOXX Roller. Specifications: Top Load Capacity: 100kg.In-box Load Capacity: 25kg.Tensile Strength: 50kg.
The Bosch L-BOXX Carry Case is made from robust, durable ABS plastic. Fitted with a click mechanism that allows stacked boxes to be easily opened for convenient handling. They can be customised to carry various tools thanks to interchangeable tool inlays. Improved storage and transportation within the Bosch Mobility System.The Bosch 136 L-BOXX Carry Case has an additional front handle for carrying the box close to the body. Suitable for all types of power tools. Specification: Top Load Capacity: 100kgIn-box Load Capacity: 25kgOuter Dimensions (width x length x height): 442 x 357 x 151mmWeight: 1.9kg
The Bosch 136 L-BOXX Carry Case offers an improved storage and transportation solution in line with the Bosch Mobility System. Stacked boxes can be easily and conveniently opened with the improved L-BOXX click mechanism. Extensive compatibility of the L-BOXX variants, tool inlays, and the Sortimo in-vehicle system provides full flexibility. It has a robust design, manufactured from durable ABS plastic. Fitted with securely closing latches and a top handle, making it easy to carry. Compatible with the L-BOXX variants, tool inlays, the Sortimo in-vehicle system, Aluminium Caddy, and L-BOXX Roller. Specifications: Top Load Capacity: 100kg.In-box Load Capacity: 25kg.Tensile Strength: 50kg.
The Bosch 6 Piece Combo Kit contains:1 x 18V GSB 18V-65 Professional Combi Drill. Performs tough drilling applications with ease thanks to improved 65Nm torque. Switchable KickBack Control prevents accidental tool kickback, keeping you safe. Tight, awkward spaces are no problem with this compact tool’s handy head length of only 175mm. Plus, you get even more illumination power for your working space with the dual working lights.Chuck Type: 13mm KeylessChuck Capacity (min./max.): 1.5/13mmNo Load Speed: 0-550/0-2,200/min.Impact Rate: 27,000/bpm.Torque Settings: 20Weight: 1.12kg excl. battery1 x 18V GWS 18V-8 Professional Angle Grinder. Packs 800W of equivalent corded power, ideal for light-duty cutting and grinding tasks. Packed with safety features and designed with a sleeker and longer grip than its predecessor, offers excellent control and ergonomic comfort. Thanks to its optimised runtime per battery charge, it saves time by letting you get more work done on less recharges.Disc Diameter: 125mmNo Load Speed: 11,000/min.Grinding Spindle Thread: M14Bore Size, Diameter: 22.23mmWeight: 1.6kg excl. battery1 x 18V GDR 18V-215 Professional Impact Driver with 2 auto driving modes; for metal and wood for screws. It can also stop automatically or slow down as soon as the impact procedure starts, preventing damage to the material and your screwheads.Tool Holder: 1/4in internal hexagonNo Load Speed: 0-2,100/0-3,300/min.Impact Rate: 0-3,000/0-3,800/bpmMax. Torque: 215NmWeight: 1kg excl. battery1 x 18V GBH 18V-22 SDS-Plus Rotary Hammer is compact, light, and ergonomically designed with a well-defined centre of gravity, so you will find it easier and less tiring to handle it, especially when drilling overhead. KickBack Control and Electronic Precision Control (EPC) provide better tool handling and increased user protection.No Load Speed: 0-1,050/min.Impact Rate: 0-4,675/bpmImpact Energy (according to EPTA 05/2016): 1.9 Joules.Drilling Diameter: Metal 13mm, Wood 20mm, Concrete with Hammer Drill Bits 4-22mm, Opt. app. range 4-12mmWeight: 2.3kg excl. battery1 x 18V GKS 18V-51 Professional Circular Saw is easy to carry and ideal for vertical and horizontal cuts because of its compact design. Designed for cross-cutting timber, ripping plywood and OSB boards, and also making bevel cuts in timber.No Load Speed: 5,800-6,300/min.Max. Cutting Depth: @90°: 51mm, @45°: 35mm.Blade: 140 x 20mm Bore.Weight: 2.2kg excl. battery.1 x 18V GST 18V-125 S Professional Jigsaw with barrel grip. The robust design and brushless motor ensure excellent tool runtime and increased tool longevity. Its simple design prioritises core functions such as SDS blade holder, LED, 4-stage pendulum, or Speed Selection.Stroke Rate at No Load: 0-3,500/min.Stroke Height: 26mmCutting Depth: Wood 125mmWeight: 1.9kg excl. batteryAlso supplied with: 3 x ProCORE 4.0Ah Batteries, 1 x GAL 18V-40 18V Battery Charger and 1 x Bosch Tool Bag.
Bosch AA1 Professional AA Battery Adaptor for more flexibility. With the AA1 adaptor you can easily switch between 4 x AA alkaline batteries and a 12V battery for flexible work. Continue working while your 12 V battery charges. Compatible with selected Measuring Tools which use the 10.8V and 12V power system.
