The Kuny's drywall Pouch with no hammer holder loop. Ideal for use when fitting plasterboard as there are no hard surfaces to cause damage. Made from durable split grain leather. Three pouches. (Large, Medium and Small) reversed for easy access. Rivet reinforced at all stress points. Fits any belt up to 76.2mm (3in) wide.
The Kuny's HM213 Leather Heavy-Duty Hammer Holder is made from Top Grain leather. The cradle design eliminates hammer pivoting. Fits belt sizes up to 70mm (2.3/4in) wide.
Vitrex 331315 P3 Multi-Purpose Replacement Filters protect the lungs against very fine toxic particles. Suitable protection from welding and smoke fumes, paint removal and toxic waste disposal. Conform to EN143:2000 FFP3 standards. Suitable for use with the Twin Filter Respirator 331300. Supplied as a pack of 2.
Moldex EasyLock® Filters for Series 7000 & 9000 masks. No need for additional clips or holders, different gas and particulate filters can be combined. EasyLock® particulate filters can either be connected to the EasyLock® gas cartridge or directly to the mask body. adaptors or particulate pre-filters are not necessary. ABEK1 protection against organic [boiling point >65°C] + inorganic gases & vapours, acid gases and ammonia. 10 x Workplace Exposure Limit (Half Mask).20 x Workplace Exposure Limit (Full Face Mask).OR 1000 ppm whichever is lower. Tested and certified to EN 14387:2004+A1:2008.
Moldex Corded Pura-Fit Disposable Earplugs are made from comfortable PU foam, this soft material is easy to insert. Ideal for protecting against long term exposure and higher noise levels. They are brightly coloured for easy compliance checks. Has a signal to noise ratio (SNR) of 36 dB.
The Moldex AIR Plus ProValve Real Reusable FPP2 Mask has a washable full face seal and offers a secure fit, that is comparable to a half mask. The AirWave® Pleated Filter reduces breathing resistance, improves wearer comfort and minimises fatigue. Offers low breathing resistance even after hours of use. The built-in ProValve reduces condensation from exhaled air. Masks are individually packaged. FFP storage bag available (MOL399401), helps keep the mask hygienic. FFP2 for protection against non-toxic dusts, mists and fumes 10 x WEL (Workplace Exposure Limit). Tested and certified to EN 149:2001+A1:2009.
Scan Palm Dipped Black Nitrile Gloves are resilient to both grease and fuel, making them ideal for handling small oily parts. The tough palm and finger nitrile coating provides effective abrasion and puncture resistance. The 13g knitted seamless polyester liner improves comfort. Conform to EN420 and EN388 Standards. Abrasion Performance Index (1-4): 4Blade Cut Performance Index (1-5): 1Tear Performance Index (1-4): 2Puncture Performance Index (1-4): 11 x Pair of Scan Palm Dipped Black Nitrile Gloves Size 8 Medium
Scan Foam Latex Coated Gloves are high-visibility orange gloves made of knitted and seamless polyester for excellent comfort. They have black latex wrinkle finish coating on the palm and fingers, which gives excellent grip and flexibility in both wet and dry conditions. The glove has a 13g knitted seamless high visibility polyester liner. Conform to EN420 and EN388 Standards. Abrasion Performance Index (1-4): 2Blade Cut Performance Index (1-5): 1Tear Performance Index (1-4): 2Puncture Performance Index (1-4): 11 x Pair of Scan Hi-Vis Yellow Foam Latex Coated Gloves Size 9 Large
The Black & Decker WM301 Workmate Bench has a durable steel frame construction and folds flat for compact storage and easy transport. The dual clamping cranks increase the clamping force and offers versatility with the adjustable swivel pegs and jaw retention grooves provide clamping versatility and reliable material hold. It has been designed for easy set-up and clean-up with rubber feet which are anti-slip. Ideal for: holds virtually anything, bench tool stand, vice for cutting, painting etc. workbench and as a sawhorse. Specification Vice Jaw Material: Compressed Bamboo.Vice Jaw Opening: 0 - 115mm.Working Height: 760mm.Vice Jaw Length: 610mm.Table Width: 341mm.Max Load: 160kg.
These Bollé Safety SILEX Safety Glasses have yellow colour lenses. Suitable for indoor use or low light situations, helping to improve contrast. Specification: Lens Type: Yellow, Anti-Fog and Anti-scratchLens Conforms to: EN 1661F/EN 170-UV 2C-1.2Frame Conforms to: EN 166FT
The DEWALT Force Gilet is suitable to wear as an under or over layer garment. It features a lightweight padding that has a shower resistant nylon outer and a polyester/taffeta inner lining. Comfort stretch side panels and lowered back with centre zip fastening. With 2 hand pockets to lower front and a zipped breast pocket. It also has a reflective DEWALT logo on the chest and rear neck. Available in Sizes Medium - XXXLarge Material Composition: Nylon outer & Polyester/Taffeta innerDEWALT Force Black Lightweight Padded Gilet in Extra Extra Extra Large
The Apache ATS Waterproof Jacket is padded, providing a good degree of warmth on a cold day. All seams are sealed to avoid water ingress. Fitted with a removable, integral storm hood with drawcord feature. The jacket features additional hardwearing panels to the shoulders and lower arms and secure elasticated cuffs. With two large side pockets and an internal zipped pocket. Reflective piping to front of jacket for added safety.1 x Apache ATS Waterproof Padded Jacket Extra Extra Large (52in)
The Raaco 1260-00 Metal Cabinet has 60 drawers, each drawer can be divided into 4 compartments. The cabinet is made of painted steel and the drawers are made of polypropylene (PP). Drawers: 60 x 150-00 (41 x 55 x 153mm).
The Raaco 1248-01 Metal Cabinet has 48 drawers, each drawer can be divided into 16 compartments. The cabinet is made of painted steel and the drawers are made of polypropylene (PP). Drawers: 48 x 150-01 (41 x 67 x 153mm).
The DEWALT Apprentice Hiker Boots have nubuck and full grain leather uppers which are hard-wearing with antibacterial insole with dual density seat. They are fitted with a steel toecap that has been tested to 200 joules. The sole is chemical and oil resistant and is made from EVA rubber. Available in Wheat or Brown. EN Test: CE EN ISO 20345-2011.Safety Rating: SB.Slip Rating: SRA.The DEWALT Apprentice Nubuck Hiker Boots have the following specification: Colour: Wheat.Size: UK 11 Euro 45.
These Scan P3 Cartridges are suitable for Scan Twin Half Mask Respirators (SCAPPERESPA1 and SCAPPERESPP2). The filters provide high efficiency protection against dust. Conforms to EN143:2000/A1:2006.
The Bahco 4750-3PB-1 Three Pouch Belt Set is made from tough, lightweight nylon and features plenty of riveting for real strength. The pouches are made from polyester. With rust proof fittings, including a tape clip. It also has 4 hooks for extra loops and 3 safety rings for lanyard attachment. Fits waist sizes up to 48 inch.
The DEWALT Pro Tradesman Trousers are a comfortable, functional work trouser featuring Cordura® holster pockets and Cordura® reinforced hems with top loading knee pad pockets. They have been triple stitched in key areas with a low rise, comfort waist. Other features include: a side utility pocket, large phone pocket to opposite leg, tunnel belt loop and YKK zip. Suitable for any professional tradesman.These DEWALT Pro Tradesman Trousers have the following specification: Colour: Black.Waist: 36 inch.Leg: 33 inch.
The Apache Industrial work/drivers' trousers are made from 260g polycotton and have bottom loading knee pad pockets, hammer loop and ruler pocket. They also have button fastening pockets at the rear. They are made from strong durable 65% polyester, 35% cotton and are ideal for all DIY or professional use. These Apache trousers are available in 2 leg lengths for optimal fit: 31, and 33 inch with sizes 32 to 42 inch waist. Size waist 32 in leg 33 in
The DEWALT Millington Rigger Boots are completely non-metallic. They have a waterproof, breathable inner lining that helps to eliminate water ingress. A composite toecap and midsole provide increased user protection. The outsole is manufactured using a dual density formula of PU and rubber, giving heat resistance to 300°C. This boot also incorporates an anti-scuff toe guard. Safety Rating: S3-WR-HROSlip Rating: SRC1 x Pair of DEWALT Millington S3 Waterproof Rigger Boots UK 8 Euro 42
These Bollé IRI-S Safety Glasses feature a bifocal reading area. They have been designed to fit all face shapes. Ultra-modular with infinitely adaptable features. The unique B-Flex shape memory bridge is height and width adjustable. They also feature pivoting non-slip ergonomic temples. Optical class 1 polycarbonate lenses with Platinum® anti-scratch and anti-fog lenses. They are supplied with sports cord. Available in a variety of reading powers. EN Standards: EN 166/170/172 1FT.These Bollé Safety IRI-S Platinum® Safety Glasses have clear lenses. Approved for permanent wear and certified with perfect optical quality with anti-fog and anti-scratch coatings, 99.9% UVA/UVB protection. Specification Bifocal Reading Area: +3.0.Lens Type: Clear, Anti-Fog and Anti-Scratch.Lens Conforms to: EN170-UV 2C-1.2.Frame Conforms to: EN1661FT.
