These cutters are used extensively for routing edge moulds, face grooves, columns, fluting, water slots, engraving and panel moulds in products such as desk tops, fire surrounds, draining boards and picture frames. These cutters are suitable for use on all natural timbers and man-made boards.TC.1/2in ShankR = 12.7 mmD = 25.4 mmC = 15.9 mm
These cutters are used extensively for routing edge moulds, face grooves, columns, fluting, water slots, engraving and panel moulds in products such as desk tops, fire surrounds, draining boards and picture frames. These cutters are suitable for use on all natural timbers and man-made boards.Tooling : T.C.T.1/4in Shank.R = 10 mmD = 20 mmC = 18 mm
These cutters are suitable for grooving, rebating, morticing and drilling. The single flute cutters offer fast free cutting. If you require a cleaner cut please use two flute cutters. The depth of cut on cutters of 2.0mm diameter and below should be a maximum of 1.0mm per pass. Small diameters in Tungsten Carbide must be handled with care to avoid breakage and very shallow passes must be made. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods Single flute cutters must not be used in eccentric chucks.Shank: 1/4in.Dimensions:Shank: 1/4inCutting Diameter (D): 1.5mmCutting Length (C): 6.0mm
The Faithfull Router Bit TCT 45° Chamfer is a bearing guided tungsten carbide tipped cutter producing a 45° chamfer to a maximum depth of 10mm. Suitable for use on softwood, hardwood and all man-made boards. 1/4in Shank
The Faithfull 15 Piece Router Bit Set with 1/2in shank. Tungsten Carbide tips ensure long life and the storage case provides a safe place to store the bits when they are not being used. Different cutter shapes enable the creation of a variety of profiles, grooves and mouldings in softwoods, hardwoods, MDF or plywood. Shank: 12.7mm (1/2in). Set Contains: (Diameter/Depth) 1 x Straight Cutter (3.2/14mm).1 x Straight Cutter (6.5/20mm).1 x Straight Cutter (12.7/25mm).1 x Straight Cutter (19.0/20mm).1 x Dovetail Cutter (12.7/8mm).1 x Panel Pilot (6.5/30mm).1 x Guided Flush Trimmer (12.7/12mm).1 x Mortising Cutter (12.7/13mm).1 x Core Box R3.2mm (7/6mm).1 x 90° V Cutter (12.7/10mm).1 x 45° Guided Chamfer (30/14mm).1 x Guided Cove R9.5mm (30/14mm).1 x Guided Rabbeting Cutter (30/10mm).1 x Guided Roman ogee (25/12mm).1 x Guided Rounding R10mm (32/16mm).
The manufacturing specification for Faithfull router bit cutters ensures that they are suitable for use by all professional tradesmen, craftsmen and conscientious DIY enthusiasts. Every Faithfull router cutter tip is made from tungsten carbide, brazed onto a steel body and designed to cut a wide variety of timber and abrasive material such as MDF and plywood. With careful handling and under normal conditions, they will outlast HSS grade cutters many times. These top quality cutters will ensure an excellent finish and provide the user with long lasting and reliable service. 1/4in ShankCutting Diameter: 6.0 mm 15/64in. Cutting Length: 16 mm. Shank Diameter: 1/4in.
Self guiding cutters with bearings mounted for trimming and bevelling timber, lippings and plastic laminate edges for cabinet making, countertop production or any shaping applications. Bearing guided cutters are suitable for both straight and curved work, bearings are normally fractionally larger than cutter diameter, to avoid surface scoring. Uses:Trimming plastic or plywood overlay.Copy profiling - use the bearing to follow a template or base edge of board. A 3 mm approximate overlap should be left before copy profiling, also when using plastic laminate always allow laminate adhesive to dry before trimming. This avoids clogging the guide bearing. Tooling Tungsten Carbide1/2in Shank.Tooling Tungsten Carbide1/4in Shank.Angle A = 90 D = 9.5 mmC = 12.7 mm
Trend guide bushes can be attached to the base of the Router. They are designed to follow the contours of a template.Guide bush guides the router when using a template. Fits directly to Trend T3,T4,T5,T5 MK2, T9,T10 and T11, and some other light duty routers. Will fit other makes when used with GB/5, GB/PLATE or UNIBASE Sub-base.
Self guiding cutters with bearings mounted for trimming and bevelling timber, lippings and plastic laminate edges for cabinet making, countertop production or any shaping applications. Bearing guided cutters are suitable for both straight and curved work, bearings are normally fractionally larger than cutter diameter, to avoid surface scoring. Uses:Trimming plastic or plywood overlay.Copy profiling - use the bearing to follow a template or base edge of board. A 3 mm approximate overlap should be left before copy profiling, also when using plastic laminate always allow laminate adhesive to dry before trimming. This avoids clogging the guide bearing. Tooling Tungsten Carbide1/2in Shank.Tooling Tungsten Carbide1/2 in Shank.Angle A = 90 D = 12.7 mmC = 25 mm
This Trend 1/2in Router Cutter Set has a range of Tungsten Carbide Tipped cutters for decorative woodworking. Suitable for softwood, hardwood, chipboard, plywood and MDF. Supplied in a plastic carry case. Contains: 2 x Straight Cutters: 6.3 x 16, 12.7 x 25mm1 x V-Groove Cutter: 45° x 12.7mm2 x Guided Round Over: R6.35mm, R9.5mm1 x Guided Ogee: R4mm
This TCT two wing slotting cutter is ideal for biscuit jointing sizes The set is supplied with 3 ball bearing guides to suit the three sizes of biscuits available. A slighlty longer cut than the length of the biscuit is required for ease of alignment during assembly Supplied with instructions. No. 0 - 45 mm x 15 mm x 4 mm Suitable for 8-12 mm boardsUse bearing B19A 9.05 mm depth No. 10 - 53 mm x 19 mm x 4 mmSuitable for 13-18 mm boardsUse bearing B16A 10.6 mm depth No. 20 - 58 mm x 23 mm x 4 mmSuitable for 19 mm + boardUse bearing B127A D1 37.2 mm Cut length 4 mm B 12.7 mm B2 16.0 mm B3 19.0 mmShank = 1/4in
Attractive edge moulds and a full corner bead can be produced by making a second pass at 90° with this TCT cutter. Used on all man-made boards such as medium density fibre board, chipboard, and also natural timbers and most plastics. T.C.T.Shank = 1/4in.R = 4.8 mmD = 26 mmd = 22 mmC = 16 mmB = 15.9 mm Craft Range - They can be used on all man-made boards such as medium density fibre board, chipboard, and also natural timbers and most plastics Bead & Reed Cutters Bead and Reed cutters are ideally suited to form straight or curved decorative edge mouldings on table tops, chair legs and frames. They can also be used to produce complete round over profiles for window boards and stair tread nosings. Cutters can be combined to form compounded one-off mouldings for individual applications. Certain staff bead cutters are used to join boards and produce hinged joints for table tops.
This Trend 3/75 x 1/2 TCT Two Flute Cutter has the following specification: D: 12mm (15/32in)C: 63mmOL: 114mmShank Diameter: 1/2in Trend Two Flute Straight Cutters produce a cleaner finish than the single flute cutters. Suitable for grooving, rebating, morticing, drilling and shallow lateral routing cuts such as recessing hinges. Corners will require a final trimming square with a hand chisel or a corner chisel. Suitable for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics. The TRE373D12TC & TRE383D12TC cutters are especially suited for drilling. TRE383M12TC has a shorter shank for Makita 3600B and 3612BR, Ryobi and Hitachi Routers.
Trend Trade range two flute router cutters have extra long shanks and are designed to meet the demanding needs of the professional trademen. They have a 2mm micrograin Tungsten Carbide tips for cutting the most abrasive materials to give extra long life. They have a PTFE coat, indicated by distinctive black colouring and produce a clean finish to abrasive timbers such as chipboard, MDF, plywood and certain hardwoods. The dimensions are etched on the extra long 40mm shanks for quick identification and are suitable for mortice and worktops applications.The TR37 is suitable for use use with Trend Lock JigsDimensions:Shank: 1/2 inCutting Diameter: 12mmCutting Length: 63mm.
Trend Lapping Fluid is designed solely for the engineering industry. It is ideal for use with diamond abrasives, where other lubricants may be too thick. Use instead of water to reduce the risk of rusting by 95%. Supplied in a flip-top dispenser bottle. Size: 100ml.
Attractive edge moulds and a full corner bead can be produced by making a second pass at 90° . Used on all man-made boards such as medium density fibre board, chipboard, and also natural timbers and most plastics. D1 7/8 inch D1 22.3 mm D2 20 mm Cut length 35/64 inch Cut length 14 mm B 12.7 mm R1 3.2 mm Shank Diameter 1/4 inch
Designed to meet the needs of both the professional tradesman and the home handyman.All are Tungsten Carbide Tipped, to ensure longevity of working life, coupled with a good quality finish to the work.Ovolo produces a stepped rounded profile along the edge of the material. The guide pin enables the cutter to follow intricate shapes. 1/4in Shank.Radius 9.5mmDepth of Cutter 16.3mmShank Diameter 1/4in
Trend TR30 Trade Shank mounted guided profiler with extra long shank ideal for trimming and profiling timber, man-made board. Features 2mm micrograin tungsten carbide tips, for cutting the most abrasive materials to give extra long life. The cutter is PTFE coated, indicated by distinctive black colouring. The guide profiler can be used on hardwood and softwood, fibreboard, plywood and particle board and has the dimensions etched on the extra long 40mm shanks, for quick identification. Dimensions:Shank: 1/2 in.Cutting Diameter: 19.1mm.Cutting Length: 50.0mm.
Trend TR28 Trade bearing guided profiler with extra long shank ideal for trimming and bevelling timber, lippings and plastic laminate edges. Features 2mm micrograin tungsten carbide tips, for cutting the most abrasive materials to give extra long life. The cutter is PTFE coated, indicated by distinctive black colouring. The dimensions etched on the extra long 40mm shanks, for quick identification. Dimensions:Shank: 1/2 in.Cutting Diameter: 12.7mmCutting Length: 25.4mm
The Trend T421/35 hinge cutter is typically used by kitchen unit manufacturers and fitters for cutting 35mm blind holes ready to accept recessed circular hinges, it has a TCT blade for longer life.This bit is best suited for use on thinner section laminate covered board.Diameter - 35mmShank - 1/4in
The Trend PH/JIG Pocket Hole Jig is great for fast and accurate joining of timber and plywood, giving strong instant joints. Solid hardened bushes with variable pitch of 29mm to 63mm. Use on timber, MDF, plywood and block board. Allows a variety of joints to be created individually. Uses square drive self tapping screws. Work piece can be handled immediately after gluing and screwing, creating time saving benefits. No clamps required.This replacement stepped drill bit for the Pocket Hole Jig has a diameter of 9.5mm (3/8in).
The Trend CB counterbore is extensively used for recessing bolt and screw heads. Supplied with a HSS slow spiral drill bit. Fully adjustable, a hex key is supplied. TCT version is used for plywood, particle boards and plastics (abrasive). Use at drilling speeds only. Not suitable for ferrous and non-ferrous metals. When setting-up, ensure flutes of drill are aligned with flute of counterbore. For replacement Twist Drills, use slow spiral type e.g 501/532 to 501/012.
Trend Bearing Guided Template Profile Cutter for rebating and trimming edges. Extra care must be taken to avoid breakage of the cutter. Two flute carbide TCT tips for clean, professional finish on timber lippings, plastic laminates and veneers. Specially designed PTFE coated bodies to minimise heat and resin build-up and Micro-granular Tungsten Carbide tips ensure a premium finish in hard and soft woods, and abrasive man-made boards such as ply, MDF and chipboard, to meet the needs of the woodworker and tradesman for quality and performance. All Trend router cutters also have a safety ‘K’ mark insertion indicator on each shank to ensure a quick and easy set up whether for hand held or table work.This Trend Bearing Guided Template Profile Cutter has the following specification: (D) Diameter: 12.7mm(C) Cutting Length: 9.5mmShank: 1/4in
Trend dovetail cutters are designed for use with commercial dovetailing and stair housing jigs. Also cutters to produce sliding and lapped dovetails, through dovetails and end on dovetails. Suitable for use on natural timbers and man-made boards, they are used extensively in cabinet work, furniture making, stair trenching, dovetail jointing and carcass construction.T.C.T.1/4in Shank.A = 104° C = 12.7mmD = 13.2 mm
