These Faithfull Professional 1/4in Hexagon Drive Star Screwdriver Bits are manufactured from high strength, heat treated ‘S2’ grade steel. Bits are shock and wear resistant and feature precision machined tips to provide an optimum fit, helping to prevent screw stripping and cam-out and provide a long working life.These Faithfull S2 Grade Steel Screwdriver Bits have the following specification: Size: T10 x 25mm.Pack Size: 3.
The Britool 1/4in bit set, comprising of 49 pieces: 6 x Slotted Bits: 4, 4.5, 5.5, 6.5x2 and 8mm.6 x Phillips® Bits: PH1x2, PH2x3 and PH3.7 x Pozidriv® Bits: PZ1x2, PZ2x3 and PZ3x2.10 x Torx® Bits: T10x2, T15x2, T20x2, T25x2 and T30x2.10 x ResisTorx® Bits: TT10, TT15x2, TT20x2, TT25x2, TT30x2 and TT40.9 x Hex Bits: 2, 3x2, 4x2, 5x2 and 6x2mm. The set also includes a magnetic bit holder with locking ring.
Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments. 28° Collation Angle Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out. (Remember only tools fitted with sequential trip should be used when working up a ladder). Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them. Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.Gauge/Diameter (mm) 2.8 Length 6528 Collation Angle SKU S280R65G8 Profile RING Finish G8 Description STICK NAIL 2.80-65 RING GAL8 2M Qty per box 2000 Will also fit the N80SB, FW28WW-E, N100S
The DEWALT DT20420 TCT Construction Circular Saw Blade has been designed for use with the DEWALT DCS571 Compact Circular Saw. Made from construction grade carbide with ultra-sharp, impact-resistant carbide teeth that help to reduce the chance of chipping or breaking a tooth. An anti-kickback shoulder provides additional safety. Specification: Diameter x Bore: 115 x 9.5mm.Teeth: 24.
Faithfull Professional Security Screwdriver Bits are designed for use with tamper-resistant, security TORX (Star) head fixings which have a small pin inside their drive recess to prevent the use of a standard TORX driver, tamper-proof fixings of this type are often found on electrical appliances. Manufactured from high-strength, heat treated ‘S2’ grade steel. These bits are shock and wear resistant and feature precision machined tips to provide an optimum fit, helping to prevent screw stripping and cam-out and provide a long working life.Pack of 3 Faithfull Security S2 Grade Steel Screwdriver Bits T25S x 25mm
LENOX® Demolition Bi-Metal-Reciprocating Saw Blades use POWER BLAST TECHNOLOGY™ to increase blade life. High-speed blasting along the cutting edge strengthens the blade to reduce breaks and increase durability. The blade design provides maximum durability. The taller and thicker blade profile prevents bending during cutting and provides maximum control in the toughest demolition applications.Pack of 2 LENOX® 20598-966R Demolition Reciprocating Saw Blades 225mm 6 TPI Ideal for demolition work and cutting nail embedded wood.
Flexipads professional quality glass polishing kit – ideal for removing light to medium scratches. It can also remove scuffs, water marks, lime scale, residue left from acid rain, adhesive particles and hairline scratches. Contents: 50ml Glass Polishing Compound75mm Backing Pad with 6mm spindle75mm Interface Cushion2 x 75mm Premium Felt Polishing Pad5 x 75mm P600 Abrasive Discs5 x 75mm P1000 Abrasive DiscsSpray BottleDust MaskPolishing Cloth
The angles flaps mean more abrasive makes contact with the workpiece than a conventional fibre disc which increases productivity. For use with Angle Grinders Ideal for sanding contoured metal surfaces, blending welds, deburring and finishing castings. Suitable for use on Metal Wood and Paint. Diameter: 125mm
The Flexovit Clipper® 115mm Multi-Materials Cutting Discs can be used for cutting brick, metal, pipe, floor tiles etc. Supplied in a handy tin with 10 discs. Manufactured to EN 12413 Standards. Specification: Size: 115 x 22.23mm BoreThickness: 1.0mmMax. Cutting Speed: 13,300/min 80 m/s
Faithfull flexible and long lasting aluminium oxide flaps are secured with a resin bond for extra strength and service life.Their design ensures a consistent finish making them ideally suited for sanding shaped and curved work pieces without the risk of clogging. The wheels have built in arbor shaft for securing in the chuck of most makes of power drills. 6mm (1/4in) shank fits all drill chucks.Size 60 x 30mmGrade Coarse (60 Grit)
Metabo Right angle drill attachment for drilling perfectly at 90° into floor and roofing joists. Perfect when working within a restricted 400mm span. Comes with a 1/2in x 20 UNF thread for all standard 13mm chucks. Rotates 360°. Recommended for use with BS/SB LT/LTX but NOT the BS18LTX Quick machines.
This Trend 3/61 x 1/4 TCT Two Flute Cutter has the following specification: D: 10mm (25/64in)C: 25mmOL: 57mmShank Diameter: 1/4in Trend Two Flute Straight Cutters produce a cleaner finish than the single flute cutters. Suitable for grooving, rebating, morticing, drilling and shallow lateral routing cuts such as recessing hinges. Corners will require a final trimming square with a hand chisel or a corner chisel. Suitable for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.
Self guiding cutters with bearings mounted for trimming and bevelling timber, lippings and plastic laminate edges for cabinet making, countertop production or any shaping applications. Bearing guided cutters are suitable for both straight and curved work, bearings are normally fractionally larger than cutter diameter, to avoid surface scoring. Uses:Trimming plastic or plywood overlay.Copy profiling - use the bearing to follow a template or base edge of board. A 3 mm approximate overlap should be left before copy profiling, also when using plastic laminate always allow laminate adhesive to dry before trimming. This avoids clogging the guide bearing. Tooling Tungsten Carbide1/2in Shank.Angle A = 90 D = 12.7 mmC = 50 mm
Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. T.C.T. Tooling1/2in Shank.T.C.T. Tooling1/2in Shank.C = 32 mmD = 12.7 mm 1/2 in
The DEWALT DT99551 FlexVolt XR Reciprocating Blade 8 Piece Set contains a selection of bi-metal blades, that are coated in a special Toughcoat finish which reduces the build up of heat, improving cutting performance and speed up to twice as much as market competitors. Suitable for applications such as cutting woods, particle boards, metals, piping, plastics, PVCs and more. Contains the following: 3 x DT99554 FlexVolt Xtreme Runtime Wood Reciprocating Blades 152mm 4/6 TPI. 1 x DT99555 FlexVolt Xtreme Runtime Wood Reciprocating Blades 230mm 4/6 TPI. 3 x DT99553 FlexVolt Xtreme Runtime Metal Reciprocating Blades 152mm 14/18 TPI. 1 x DT99552 FlexVolt Xtreme Runtime Metal Reciprocating Blade 203mm 14/18 TPI. 1 x ToughCase Blade Carry Case.
The Lessmann DIY Wheel Brushes are fitted with a 6mm shank and are generally used for the removal of rust, paint or dirt and for roughening, de-burring, stripping or polishing. Available in Steel or Brass.The Lessmann DIY Wheel Brush has the following specification: Wire Type: SteelDiameter: 100mm.Width: 8-10mm.Wire Gauge: 0.30.Shank: 6mm.Max Speed: 4,500/rpm.
Starrett BU214-5 Multi Purpose Jig Saw Blades with Unified Shank™. These blades will fit in virtually all jigsaw machines. These blades feature 170% more weld contact area than standard bi-metal blades through the Unique™ solid state diffusion bonding process. This ensures exceptionally strong teeth, combined with the multiple cutting edges and split chip advantage, ensure that these blades typically last 25% longer than directly competing products. Supplied in a pack of 5. Specification Length: 50mm, ;Width: 7.5mm, Thickness: 1mm.TPI: 14.Tooth: Regular, Set: Wavy.Capacity: Non Ferrous Metal: 4.8-6.4mm, Wood: 6-30mm & Plastic: 3-12mm. Length dimension references the tooth bearing section of the blades, the total length including shank is approximately 25mm longer.
The DEWALT Stationary Construction Circular Saw Blade has impact resistant carbide teeth that help to reduce the chance of chipping or breaking a tooth. With ultra-sharp cutting edges and Alternate Top Bevel (ATB) teeth to reduce splinters. The blade features a wedge shoulder to protect the carbide from nail impact. The fast, smooth cutting action and durable construction makes it ideal for demanding jobsite operations, rough timber and cutting through embedded nails.This DEWALT Construction Circular Saw Blade has been designed for cutting rough timber, possibly with embedded nails. Specification: Blade Diameter: 250mmBlade Bore: 30mmTooth Count: 48Plate Thickness: 2.2mmKerf Thickness: 3.0mmGrind Type: ATBRake Angle: +10°
The DEWALT Sanding belts have a heavy-duty backing cloth, resin bonded for use with belt sanders. They provide excellent grain adhesion and heat resistance for power sanding and have a high quality aluminium oxide grain for fast, aggressive stock removal and fine finishing. Anti static bond and backing ensures more efficient dust extraction, improved finish and longer life. Applications: for all stripping, sanding and finishing tasks on wood, metal and painted surfaces.Pack of 3 DEWALT Sanding Belts 560 x 100mm 100g (Pack of 3)
