JG Speedfit radiator outlet plate allows 10mm pipes to be dropped down from above pipe runs to relevant radiator positions. This means all pipework is concealed within the wall and behind the radiator.The JG Speedfit radiator outlet plate creates a neat outlet for 10mm supply pipes to a radiator. To be used with single gang 25mm steel KO boxes to BS4662, fitted with rubber grommet. Radiator outlet plate for 10mm pipe Ideal to mount within a standard 15mm single gang stainless steel KO box Rubber grommet Compatible with plastic or copper pipe (inserts required) Suitable for central heating systems
JG Speedfit female coupler tap connector push-fit fitting for the connection of plastic or copper pipes to a male thread fixture or appliance. The female coupler is ideal for the connection of taps and toilets. Simply push the push-fit fitting fully onto the pipe and hand turn onto the thread. To demount the connection, push the collet towards the body of the push-fit fitting and pull the pipe to release. The JG Speedfit female coupler tap connector is up to 40% faster to install than traditional methods and is easier to use in confined spaces by removing the need for hot works and tools. Designed, manufactured and assembled in the UK. Instant push-fit and hand-tighten connection Install and demount in seconds without tools Safe flame-free installation, with no hot works, glue or flux Grip & Seal collet with stainless steel teeth and main O-Ring seal Compatible with Speedfit PEX and polybutylene plastic pipe (inserts required) and copper pipe Suitable for hot and cold water and central heating systems
JG Speedfit reducing elbow push-fit fitting for the connection of unequal sized plastic or copper pipe to form a 90¡ bend. Simply push the push-fit fitting fully onto the pipe and twist the plastic nut clockwise to lock in place. To demount the connection, unlock the nut by hand and push the collet towards the body of the push-fit fitting and pull the pipe to release. The JG Speedfit reducing elbow push-fit fitting is up to 40% faster to install than traditional methods and is easier to use in confined spaces by removing the need for hot works and tools. Designed, manufactured and assembled in the UK. Instant push-fit connection Install and demount in seconds without tools Safe flame-free installation, with no hot works, glue or flux Grip & Seal collet with stainless steel teeth and main O-Ring seal Twist & Lock mechanism secures fitting and adds compression Non-toxic, resists corrosion and no scale build-up Compatible with Speedfit PEX and polybutylene plastic pipe (inserts required) and copper pipe Suitable for hot and cold water and central heating systems
JG Speedfit female coupler tap connector push-fit fitting for the connection of plastic or copper pipes to a male thread fixture or appliance. The female coupler is ideal for the connection of taps and toilets. Simply push the push-fit fitting fully onto the pipe and hand turn onto the thread. To demount the connection, push the collet towards the body of the push-fit fitting and pull the pipe to release. The JG Speedfit female coupler tap connector is up to 40% faster to install than traditional methods and is easier to use in confined spaces by removing the need for hot works and tools. Designed, manufactured and assembled in the UK. Instant push-fit and hand-tighten connection Install and demount in seconds without tools Safe flame-free installation, with no hot works, glue or flux Grip & Seal collet with stainless steel teeth and main O-Ring seal Compatible with Speedfit PEX and polybutylene plastic pipe (inserts required) and copper pipe Suitable for hot and cold water and central heating systems
JG Speedfit reducing elbow push-fit fitting for the connection of unequal sized plastic or copper pipe to form a 90¡ bend. Simply push the push-fit fitting fully onto the pipe and twist the plastic nut clockwise to lock in place. To demount the connection, unlock the nut by hand and push the collet towards the body of the push-fit fitting and pull the pipe to release. The JG Speedfit reducing elbow push-fit fitting is up to 40% faster to install than traditional methods and is easier to use in confined spaces by removing the need for hot works and tools. Designed, manufactured and assembled in the UK. Instant push-fit connection Install and demount in seconds without tools Safe flame-free installation, with no hot works, glue or flux Grip & Seal collet with stainless steel teeth and main O-Ring seal Twist & Lock mechanism secures fitting and adds compression Non-toxic, resists corrosion and no scale build-up Compatible with Speedfit PEX and polybutylene plastic pipe (inserts required) and copper pipe Suitable for hot and cold water and central heating systems
JG Speedfit reducing tee push-fit fitting for the connection of three unequal sized plastic or copper pipes. Simply push the push-fit fitting fully onto the pipe and twist the plastic nut clockwise to lock in place. To demount the connection, unlock the nut by hand and push the collet towards the body of the push-fit fitting and pull the pipe to release. The JG Speedfit reducing tee push-fit fitting is up to 40% faster to install than traditional methods and is easier to use in confined spaces by removing the need for hot works and tools. Designed, manufactured and assembled in the UK. Instant push-fit connection Install and demount in seconds without tools Safe flame-free installation, with no hot works, glue or flux Grip & Seal collet with stainless steel teeth and main O-Ring seal Twist & Lock mechanism secures fitting and adds compression Non-toxic, resists corrosion and no scale build-up Compatible with Speedfit PEX and polybutylene plastic pipe (inserts required) and copper pipe Suitable for hot and cold water and central heating systems
JG Speedfit equal elbow push-fit fitting for the connection of equal sized plastic or copper pipe to form a 90¡ bend. Simply push the push-fit fitting fully onto the pipe and twist the plastic nut clockwise to lock in place. To demount the connection, unlock the nut by hand and push the collet towards the body of the push-fit fitting and pull the pipe to release. The JG Speedfit equal elbow push-fit fitting is up to 40% faster to install than traditional methods and is easier to use in confined spaces by removing the need for hot works and tools. Designed, manufactured and assembled in the UK. Instant push-fit connection Install and demount in seconds without tools Safe flame-free installation, with no hot works, glue or flux Grip & Seal collet with stainless steel teeth and main O-Ring seal Twist & Lock mechanism secures fitting and adds compression Non-toxic, resists corrosion and no scale build-up Compatible with Speedfit PEX and polybutylene plastic pipe (inserts required) and copper pipe Suitable for hot and cold water and central heating systems
JG Speedfit equal elbow push-fit fitting for the connection of equal sized plastic or copper pipe to form a 90¡ bend. Simply push the push-fit fitting fully onto the pipe and twist the plastic nut clockwise to lock in place. To demount the connection, unlock the nut by hand and push the collet towards the body of the push-fit fitting and pull the pipe to release. The JG Speedfit equal elbow push-fit fitting is up to 40% faster to install than traditional methods and is easier to use in confined spaces by removing the need for hot works and tools. Designed, manufactured and assembled in the UK. Instant push-fit connection Install and demount in seconds without tools Safe flame-free installation, with no hot works, glue or flux Grip & Seal collet with stainless steel teeth and main O-Ring seal Twist & Lock mechanism secures fitting and adds compression Non-toxic, resists corrosion and no scale build-up Compatible with Speedfit PEX and polybutylene plastic pipe (inserts required) and copper pipe Suitable for hot and cold water and central heating systems
John Guest Speedfit products blend push-fit and multi-seal technology for a reliable leak-proof connection. Simple to install and no tools are required when installing or demounting fittings, making it easy to manoeuvre in tight spaces or readjust joins. SpeedfitÕs extensive choice of plastic, brass and chrome fittings, tap connectors, valves and flexi hoses gives you everything you need to complete the job in no time. By combining these products with plastic push-fit pipe, you can create a truly flexible plumbing and heating system. All products are accredited with the leading testing and approval organisations including WRAS and are suitable for use with plastic or copper pipe. Push-fit plastic fitting for the connection of plastic and copper pipe. Simply push the fitting fully onto the pipe and twist the plastic nut clockwise to lock in place. Should the need arise to demount the connection unlock the nut and push the collet towards the body of the fitting and pull the pipe to release. The fitting ensures an easier working environment in confined places and removes the need for hot works on site. ¥ Suitable for hot and cold water services, central heating systems and combi systems ¥ BS EN 7291 parts 1, 2, 3 and S, WRAS approved ¥ Secure and easy demounting without the need for a tool ¥ 50 year guarantee ¥ Minimum operating temperature - 20 ¡C ¥ Maximum operating temperature - 105 ¡C ¥ Maximum operating pressure at minimum temperature - 12 BAR ¥ Maximum operating pressure at maximum temperature - 3 BAR Technical specification Brand JG Speedfit Colour White Material Plastic Manufacturer ID PEM222222W Warranty (years) 50 Angle (¡) 90 Diameter (mm) 22 Pack Size 1 Fitting Type Elbow Equal or Reducing Equal
John Guest Speedfit products blend push-fit and multi-seal technology for a reliable leak-proof connection. Simple to install and no tools are required when installing or demounting fittings, making it easy to manoeuvre in tight spaces or readjust joins. SpeedfitÕs extensive choice of plastic, brass and chrome fittings, tap connectors, valves and flexi hoses gives you everything you need to complete the job in no time. By combining these products with plastic push-fit pipe, you can create a truly flexible plumbing and heating system. All products are accredited with the leading testing and approval organisations including WRAS and are suitable for use with plastic or copper pipe. Push-fit plastic fitting for the connection of plastic and copper pipe. Simply push the fitting fully onto the pipe and twist the plastic nut clockwise to lock in place. Should the need arise to demount the connection unlock the nut and push the collet towards the body of the fitting and pull the pipe to release. The fitting ensures an easier working environment in confined places and removes the need for hot works on site. ¥ Suitable for hot and cold water services, central heating systems and combi systems ¥ BS EN 7291 parts 1, 2, 3 and S, WRAS approved ¥ Secure and easy demounting without the need for a tool ¥ 50 year guarantee ¥ Minimum operating temperature - 20 ¡C ¥ Maximum operating temperature - 105 ¡C ¥ Maximum operating pressure at minimum temperature - 12 BAR ¥ Maximum operating pressure at maximum temperature - 3 BAR Technical specification Brand JG Speedfit Colour White Material Plastic Manufacturer ID PEM222222W Warranty (years) 50 Angle (¡) 90 Diameter (mm) 22 Pack Size 1 Fitting Type Elbow Equal or Reducing Equal
John Guest Speedfit products blend push-fit and multi-seal technology for a reliable leak-proof connection. Simple to install and no tools are required when installing or demounting fittings, making it easy to manoeuvre in tight spaces or readjust joins. SpeedfitÕs extensive choice of plastic, brass and chrome fittings, tap connectors, valves and flexi hoses gives you everything you need to complete the job in no time. By combining these products with plastic push-fit pipe, you can create a truly flexible plumbing and heating system. All products are accredited with the leading testing and approval organisations including WRAS and are suitable for use with plastic or copper pipe. Push-fit plastic fitting for the connection of plastic and copper pipe. Simply push the fitting fully onto the pipe and twist the plastic nut clockwise to lock in place. Should the need arise to demount the connection unlock the nut and push the collet towards the body of the fitting and pull the pipe to release. The fitting ensures an easier working environment in confined places and removes the need for hot works on site. ¥ Suitable for hot and cold water services, central heating systems and combi systems ¥ BS EN 7291 parts 1, 2, 3 and S, WRAS approved ¥ Secure and easy demounting without the need for a tool ¥ 50 year guarantee ¥ Minimum operating temperature - 20 ¡C ¥ Maximum operating temperature - 105 ¡C ¥ Maximum operating pressure at minimum temperature - 12 BAR ¥ Maximum operating pressure at maximum temperature - 3 BAR Technical specification Brand JG Speedfit Colour White Material Plastic Manufacturer ID PEM222222W Warranty (years) 50 Angle (¡) 90 Diameter (mm) 22 Pack Size 1 Fitting Type Elbow Equal or Reducing Equal
JG Speedfit cold water service stop end that quickly and easily caps off MDPE pipework at termination points on a temporary or permanent basis. The uniquely designed push-fit fitting incorporates stainless teeth to provide a tight and secure grip on the pipe. Simply push the JG Speedfit cold water service stop end fully onto the pipe. The connection is demountable, making it easy to work with in the ground when maintaining or altering an existing set-up. Designed, manufactured and assembled in the UK. Instant push-fit connection Install and demount in seconds without tools Stainless steel teeth grab ring provides extra grip on the pipe Durable material with high impact resistance Non-toxic and no scale build-up Resists corrosion and biological growth Compatible with MDPE pipes only (inserts required) Suitable for cold water use only
JG Speedfit cold water service stop end that quickly and easily caps off MDPE pipework at termination points on a temporary or permanent basis. The uniquely designed push-fit fitting incorporates stainless teeth to provide a tight and secure grip on the pipe. Simply push the JG Speedfit cold water service stop end fully onto the pipe. The connection is demountable, making it easy to work with in the ground when maintaining or altering an existing set-up. Designed, manufactured and assembled in the UK. Instant push-fit connection Install and demount in seconds without tools Stainless steel teeth grab ring provides extra grip on the pipe Durable material with high impact resistance Non-toxic and no scale build-up Resists corrosion and biological growth Compatible with MDPE pipes only (inserts required) Suitable for cold water use only
Always use a JG Speedfit pipe insert when connecting Speedfit pipe to a Speedfit push-fit fitting or when connecting to a compression fitting. Inserts play a vital role in providing extra support to pipework, ensuring that the ends of the pipe are kept nice and round, and minimising any loss of shape that can occur when cutting. Designed and manufactured in the UK. Enhances sealing for a securer connection Maintains structural integrity of the pipe connection Helps make the pipe more rigid when a side load is applied Suitable for hot and cold water and central heating systems
JG Speedfit 4 way push-fit manifold for splitting a main supply line into four reduced outlet feeds. Simply push the pipe fully onto the push-fit fitting. To demount the connection, push the collet towards the body of the push-fit fitting and pull the pipe to release. The JG Speedfit 4 way push-fit manifold is up to 40% faster to install than traditional methods and is easier to use in confined spaces by removing the need for hot works and tools. Designed, manufactured and assembled in the UK. Instant push-fit connection Install and demount in seconds without tools Safe flame-free installation, with no hot works, glue or flux Grip & Seal collet with stainless steel teeth and main O-Ring seal Non-toxic, resists corrosion and no scale build-up Compatible with Speedfit PEX and polybutylene plastic pipe (inserts required) and copper pipe Suitable for hot and cold water only (not suitable for central heating systems)
John Guest tube cutter is designed for accurately cutting LLDPE tubing up to 22mm. Simply mark where the pipe needs to be cut and then use the handy clamp action to cut a square edge, prefect for pipe insertion into a John Guest fitting. Suitable for sizes up to 22mm
John Guest tube cutter is designed for accurately cutting LLDPE tubing up to 22mm. Simply mark where the pipe needs to be cut and then use the handy clamp action to cut a square edge, prefect for pipe insertion into a John Guest fitting. Suitable for sizes up to 22mm
JG Speedfit 4 way push-fit manifold for splitting a main supply line into four reduced outlet feeds. Simply push the pipe fully onto the push-fit fitting. To demount the connection, push the collet towards the body of the push-fit fitting and pull the pipe to release. The JG Speedfit 4 way push-fit manifold is up to 40% faster to install than traditional methods and is easier to use in confined spaces by removing the need for hot works and tools. Designed, manufactured and assembled in the UK. Instant push-fit connection Install and demount in seconds without tools Safe flame-free installation, with no hot works, glue or flux Grip & Seal collet with stainless steel teeth and main O-Ring seal Non-toxic, resists corrosion and no scale build-up Compatible with Speedfit PEX and polybutylene plastic pipe (inserts required) and copper pipe Suitable for hot and cold water and central heating systems
JG Speedfit cold water service reducing straight connector for the connection of two unequal MDPE pipe sizes. The uniquely designed push-fit fitting incorporates stainless teeth to provide a tight and secure grip on the pipe. Simply push the push-fit fitting fully onto the pipe. The connection is demountable, making it easy to work with in the ground when maintaining or altering an existing set-up. The JG Speedfit cold water service reducing straight connector is up to 40% faster to install than traditional methods and is easier to use in confined spaces by removing the need for hot works and tools. Designed, manufactured and assembled in the UK. Instant push-fit connection Install and demount in seconds without tools Stainless steel teeth grab ring provides extra grip on the pipe Durable material with high impact resistance Non-toxic and no scale build-up Resists corrosion and biological growth Compatible with MDPE pipes only (inserts required) Suitable for cold water use only
JG Speedfit cold water service reducing straight connector for the connection of two unequal MDPE pipe sizes. The uniquely designed push-fit fitting incorporates stainless teeth to provide a tight and secure grip on the pipe. Simply push the push-fit fitting fully onto the pipe. The connection is demountable, making it easy to work with in the ground when maintaining or altering an existing set-up. The JG Speedfit cold water service reducing straight connector is up to 40% faster to install than traditional methods and is easier to use in confined spaces by removing the need for hot works and tools. Designed, manufactured and assembled in the UK. Instant push-fit connection Install and demount in seconds without tools Stainless steel teeth grab ring provides extra grip on the pipe Durable material with high impact resistance Non-toxic and no scale build-up Resists corrosion and biological growth Compatible with MDPE pipes only (inserts required) Suitable for cold water use only
John Guest push-fit acetal service valve metric is used to temporarily shut off hot or cold water supply to a drinks dispense fixture or fitting. The ball valve is easily operated with a _ turn screwdriver slot and is also suitable for hot and cold water applications.Fast and simple to install, John Guest valves create an instant push-fit connection and leak tight seal without the need for tools, hot works or sealing agents. The unique collet locking design firmly and securely holds the pipe in place without deforming the pipe or restricting flow. John Guest push-fit valves are corrosion resistant and fully demountable, improving system performance and reducing system downtime during maintenance. All John Guest fittings are manufactured and assembled in the UK. Durable acetal copolymer material with nitrile O-rings Instant push-fit connection and leak tight seal Connect, disconnect and reconnect in seconds without tools No scale build up improves performance and equipment lifespan Superior flow characteristics Suitable for hot and cold water Compatible with LLDPE or soft metal pipe/tubing
JG Speedfit reducer push-fit fitting for the connection of plastic or copper pipe. The reduced spigot end allows for two Speedfit push-fit fittings to be joined, creating a swivel type connection while reducing the line size. Simply push the push-fit fitting fully onto the pipe and twist the plastic nut clockwise to lock in place. To demount the connection, unlock the nut by hand and push the collet towards the body of the push-fit fitting and pull the pipe to release.The JG Speedfit reducer push-fit fitting is up to 40% faster to install than traditional methods and is easier to use in confined spaces by removing the need for hot works and tools. Designed, manufactured and assembled in the UK. Instant push-fit connection Install and demount in seconds without tools Safe flame-free installation, with no hot works, glue or flux Grip & Seal collet with stainless steel teeth and main O-Ring seal Twist & Lock mechanism secures fitting and adds compression Non-toxic, resists corrosion and no scale build-up Compatible with Speedfit PEX and polybutylene plastic pipe (inserts required) and copper pipe Suitable for hot and cold water and central heating systems
JG Speedfit reducer push-fit fitting for the connection of plastic or copper pipe. The reduced spigot end allows for two Speedfit push-fit fittings to be joined, creating a swivel type connection while reducing the line size. Simply push the push-fit fitting fully onto the pipe and twist the plastic nut clockwise to lock in place. To demount the connection, unlock the nut by hand and push the collet towards the body of the push-fit fitting and pull the pipe to release.The JG Speedfit reducer push-fit fitting is up to 40% faster to install than traditional methods and is easier to use in confined spaces by removing the need for hot works and tools. Designed, manufactured and assembled in the UK. Instant push-fit connection Install and demount in seconds without tools Safe flame-free installation, with no hot works, glue or flux Grip & Seal collet with stainless steel teeth and main O-Ring seal Twist & Lock mechanism secures fitting and adds compression Non-toxic, resists corrosion and no scale build-up Compatible with Speedfit PEX and polybutylene plastic pipe (inserts required) and copper pipe Suitable for hot and cold water and central heating systems
The John guest 3/8Ó OD x 3/8Ó NPT push-to-connect to male valve is manufactured from white polypropylene and equipped with epdm o-rings utilizing John guestÕs push-fit technology to make easy, reliable, leak-free connections. They have been developed to satisfy the compatibility needs for a wide range of applications and can be used on plastic or soft copper tubing. To make a connection, the tube is simply pushed in by hand; the unique John guest collet locking system holds the tubing firmly in place. Disconnection is just as easy and requires no special tools.About this item
John guest push-to-connect technology provides a simple, reliable, leak-free connection
Manufactured from white polypropylene and equipped with EPDM o-rings
Can be used with plastic or soft Copper tubing
Manufactured with FDA compliant materials and NSF 61 and 51 certified
Lead-free, corrosion free, non-toxic, and more chemically resistant than other plastics
Pack of 5
