BT13 Series 18 gauge brown Brad nails for use with the Bostitch brad nailer. Finish nails (Brads) are normally of a rectangular cross section instead of being round. Their diameters are less than the coil and stick nails, and are primarily used for finish and trim work in the construction and joinery industries.Length : 15mm.Colour : Brown.Pack : Clam pack of 1000.
Senco DuraSpin® Collated Screws for Drywall to Wood applications. Phillips No.2 drive, black phosphate finish, coarse thread, bugle head. 50 screws per strip. CE-marked (EN145566). Suitable for both cordless and mains operated machines.Senco DuraSpin® Collated Screws for Drywall to Wood. Size: 3.9 x 35mm.
Senco DuraSpin® Collated Screws for Drywall to Wood applications. Phillips No.2 drive, black phosphate finish, coarse thread, bugle head. 50 screws per strip. CE-marked (EN145566). Suitable for both cordless and mains operated machines.Senco DuraSpin® Collated Screws for Drywall to Wood. Size: 3.9 x 25mm.
Senco 34° angled collated brad nails with a sharp chisel point, smooth shank, D-head and Galvanised finish.Senco Chisel Smooth Brad Nails Galvanised Size: 15G x 44mm.
BT13 Series 18 gauge brown Brad nails for use with the Bostitch brad nailer. Finish nails (Brads) are normally of a rectangular cross section instead of being round. Their diameters are less than the coil and stick nails, and are primarily used for finish and trim work in the construction and joinery industries.Length : 45mm.Colour : Brown.Pack : Clam pack of 1000.
Packs of 2000 Round head nails. These plastic collated stick nails traditionally have a full round head, while only giving marginally better holding power to clipped head nails, they are preferred by the construction industry. Collation is angled at 21° to accommodate the overlapping heads. Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them. Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.Gauge/Diameter (mm) 2.8 Length 50 21° Collation AngleProfile RING Finish BRIGHT Description RH STICK 2.80-50 RING 2M Qty per box 2000 Will Fit F21PL-E, N79RH-2
Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments. 28° Collation Angle Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out. (Remember only tools fitted with sequential trip should be used when working up a ladder). Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them. Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.Gauge/Diameter (mm) 2.8 Length 75 28 Collation AngleSKU S280R75G8 Profile RING Finish G8 Description STICK NAIL 2.80-75 RING GAL8 2M Qty per box 2000 Will also fit the N80SB, FW28WW-E, N100S
The DEWALT 16 Gauge Stainless Steel 20° Finish Nails have been designed for use with the DEWALT 16 gauge nailer, ensuring fewer jamming or fitment issues. Manufactured from high quality stainless steel for a high resistance to rust. DEWALT nails are made from inspected high quality steel to ensure reliability in performance.These DEWALT DNBA1632SZ 16 Gauge 20° Finish Nails have the following specification: Length: 32mm.Type: 20° Angled Nails.Finish: Stainless Steel.Gauge: 1.6 (16GA).Box Quantity: 2500.
BT13 Series 18 gauge brown Brad nails for use with the Bostitch brad nailer. Finish nails (Brads) are normally of a rectangular cross section instead of being round. Their diameters are less than the coil and stick nails, and are primarily used for finish and trim work in the construction and joinery industries.Length : 35mm.Colour : Brown.Pack : Clam pack of 1000.
Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments. 28° Collation Angle Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out. (Remember only tools fitted with sequential trip should be used when working up a ladder). Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them. Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.Gauge/Diameter (mm) 3.1 Length 90 28 Collation AngleSKU S31090 Profile PLAIN Finish BRIGHT Description STICK NAIL 3.10-90 PLAIN 2M Qty per box 2000 Will also fit the N80SB, FW28WW-E, N100S
These DEWALT narrow crown galvanised staples are compatible with the DEWALT DCN681 and DCN682 plus other brand SX staplers. Suitable for woodworkers, carpenters, cabinet shops, shop fitting and flooring contractors, upholsters, landscapers and builders. A staple crown has more surface area, sinks solidly and resists shoot-through. Two legs give superior holding power over pins.1 x Pack of 5000 DEWALT DSTSX19Z 18G Galvanised Staples 19mm
Designed for high volume operation, coils contain large quantities of nails meaning that reloading down time can be kept to a minimum. You will find them in the pallet and crate, fencing, garden furniture and the construction industries. All Coil Nails are Round Head nails. Typically: Coils of nails with diameters from 2.0 mm to 2.2 mm contain 350 nails. Coils of nails with diameters from 2.5 mm to 3.1 mm. Contain 225 nails. Roofing nail coils contain 120 nails, due to the extra large diameter of the head. 15° Collation angle Ring shank nails have a series of rings punched into the surface of the shank. A difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising, or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails. For use with: N57C-1CE heavy-duty Coil Nailer N58C-1-E Coil Nailer N58C-1-E Coil Nailer N66C-2-E Coil NailerFinish: Bright.Size: 2.3 x 45mm.Box quantity: 16,500.
Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments. 28° Collation Angle Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out. (Remember only tools fitted with sequential trip should be used when working up a ladder). Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them. Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.Gauge/Diameter (mm) 3.1 Length 90 28 Collation AngleSKU S310R90G8 Profile RING Finish G8 Description STICK NAIL 3.10-90 RING GAL8 2M Qty per box 2000 Will also fit the N80SB, FW28WW-E, N100S
Senco DuraSpin® Collated Decking screws with a green Weatherex coating. Square No.2 drive, coarse thread. 50 screws per strip. CE-marked (EN145566). Suitable for both cordless and mains operated machines.Senco DuraSpin® Collated Decking Screws with Weatherex coating. Size: 4.2 x 55mm.
Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments. 28° Collation Angle Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out. (Remember only tools fitted with sequential trip should be used when working up a ladder). Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them. Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.Type - Stick nail RingGauge/Diameter (mm) 2.8 Length 50 Collation Angle 28 DegreesSKU S280R50G8 Profile RING Finish G8 Description STICK NAIL 2.80-50 RING GAL8 2M Qty per box 2000 Note: This nail will also fit the N80SB, FW28WW-E, N100S
The DEWALT Galvanised Ring Shank Nails are paper-taped for use with the DEWALT DCN692 Nailer and other popular brand first fix angled nailers. Annular rings for ultimate grip on first fix, framing applications. Galvanised finish for increased durability, suitable for indoor and outdoor use. Paper-taped for easy loading, handling and a cleaner job. Inclination of the nails in the casing is 33-34°.1 x Box of 2,200 DEWALT DNPT28R63 Galvanised 33° Angle Ring Shank Nails 2.8 x 63mm
DEWALT 2nd Fix 15 Gauge DA Finish Nails have a smooth shank and are compatible with most 15Ga 34° angled nailers for a wide range of applications. Made from inspected high-quality steel to ensure reliability in performance. Galvanised (G) and Stainless Steel (S/S) options available. Pack Quantity: 1 x Box 40001 x Box of 4000 DEWALT 15 Gauge Galvanised DA Finish Nails 38mm
DEWALT 2nd Fix 15 Gauge DA Finish Nails have a smooth shank and are compatible with most 15Ga 34° angled nailers for a wide range of applications. Made from inspected high-quality steel to ensure reliability in performance. Galvanised (G) and Stainless Steel (S/S) options available. Pack Quantity: 1 x Box 40001 x Box of 4000 DEWALT 15 Gauge Stainless Steel DA Finish Nails 38mm
Senco DuraSpin® Collated Screws for Drywall to Wood applications. Phillips No.2 drive, black phosphate finish, coarse thread, bugle head. 50 screws per strip. CE-marked (EN145566). Suitable for both cordless and mains operated machines.Senco DuraSpin® Collated Screws for Drywall to Wood. Size: 4.5 x 75mm.
Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments. 28° Collation Angle Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out. (Remember only tools fitted with sequential trip should be used when working up a ladder). Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them. Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.Gauge/Diameter (mm) 2.8 Length 7528 Collation Angle SKU S28075 Profile PLAIN Finish BRIGHT Description STICK NAIL 2.80-75 PLAIN 2M Qty per box 2000 Will also fit the N80SB, FW28WW-E, N100S
BT Series galvanised 18 gauge Brad fasteners for use with the Bostitch Finish Bradders. Joined with an adhesive coating that holds the brads together. Finish nails (Brads) are normally of a rectangular cross section instead of being round. Their diameters are less than the coil and stick nails, and are primarily used for finish and trim work in the construction and joinery industries.Gauge/Diameter (mm) 18 GA Length 50 SKU BT1350GA Finish GALV Description MINIBRADS 50 GALVA 5M Qty per box 5000
Designed for high volume operation, coils contain large quantities of nails meaning that reloading down time can be kept to a minimum. You will find them in the pallet and crate, fencing, garden furniture and the construction industries. All Coil Nails are Round Head nails. Typically: Coils of nails with diameters from 2.0 mm to 2.2 mm contain 350 nails. Coils of nails with diameters from 2.5 mm to 3.1 mm. Contain 225 nails. Roofing nail coils contain 120 nails, due to the extra large diameter of the head. 15° Collation angle Ring shank nails have a series of rings punched into the surface of the shank. A difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising, or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails. For use with: N57C-1CE heavy-duty Coil Nailer N58C-1-E Coil Nailer N58C-1-E Coil Nailer N66C-2-E Coil NailerFinish: Bright.Size: 2.3 x 50mm.Pack quantity: 13,200.
Senco DuraSpin® Collated Decking screws with a green Weatherex coating. Square No.2 drive, coarse thread. 50 screws per strip. CE-marked (EN145566). Suitable for both cordless and mains operated machines.Senco DuraSpin® Collated Decking Screws with Weatherex coating. Size: 4.2 x 50mm.
DEWALT 2nd Fix 15 Gauge DA Finish Nails have a smooth shank and are compatible with most 15Ga 34° angled nailers for a wide range of applications. Made from inspected high-quality steel to ensure reliability in performance. Galvanised (G) and Stainless Steel (S/S) options available. Pack Quantity: 1 x Box 40001 x Box of 4000 DEWALT 15 Gauge Galvanised DA Finish Nails 50mm
These DEWALT 9G G12 Galvanised Staples are designed to be used with the DCFS950 Fencing Stapler. G12 galvanised for outdoor durability.Pack of 960 DEWALT DFS9175B1G 9G G12 Galvanised Staples 45mm
The DEWALT Galvanised Ring Shank Nails are paper-taped for use with the DEWALT DCN692 Nailer and other popular brand first fix angled nailers. Annular rings for ultimate grip on first fix, framing applications. Galvanised finish for increased durability, suitable for indoor and outdoor use. Paper-taped for easy loading, handling and a cleaner job. Inclination of the nails in the casing is 33-34°.1 x Box of 2,200 DEWALT DNPT28R75 Galvanised 33° Angle Ring Shank Nails 2.8 x 75mm
These DEWALT 16 Gauge Galvanised Finish Nails are compatible with most 16Ga straight magazine nailers. Suitable for a wide range of applications. Made from inspected high-quality steel to ensure reliability in performance. Galvanised nails reduce the likelihood of rust or staining. Available in packs of 2500 and 5000.1 x Box of 2500 DEWALT 16 Gauge Galvanised Finish Nails 64mm
Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments. 28° Collation Angle Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out. (Remember only tools fitted with sequential trip should be used when working up a ladder). Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them. Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.Gauge/Diameter (mm) 3.1 Length 90 28 Collation AngleSKU S310R90 Profile RING Finish BRIGHT Description STICK NAIL 3.10-90 RING 2M Qty per box 2000Will also fit the N80SB, FW28WW-E, N100S
These DEWALT 9G G12 Galvanised Staples are designed to be used with the DCFS950 Fencing Stapler. G12 galvanised for outdoor durability.Pack of 960 DEWALT DFS9150B1G 9G G12 Galvanised Staples 40mm
