These Forgefix Phillips, single thread Drywall Screws have a black phosphate finish for increased durability. The screws come complete with a Phillips No.2 insert bit. Their Bugle Head allows the screw to sink effortlessly into the dry lining without the need for countersinking, which in turn minimises the damage to the surface. APPLICATION:Designed for fitting dry linings to studding. Phosphate coatings are made up of thin crystalline layers of phosphate compounds that adhere to the surface of the fixing or fastener. The phosphate crystals are porous and can be formed from zinc, manganese, or iron phosphate solutions. Phosphate coatings offer good corrosion resistance and have an excellent ability to absorb supplementary coatings which improves appearance, corrosion resistance and resistance to abrasion. The Phillips screw has four simple tapered slots. It is designed so that a Phillips tip screwdriver can turn a Phillips screw with increasing torque. When the torque gets to be too strong for the tip then the screwdriver tip winds itself out of the screw thus preventing over-tightening and or damage to the screw head. Coarse thread screws (mainly drywall screws) have an extremely sharp point and are designed to penetrate plasterboard skin. The coarse thread eases in to the board then the timber baton holding the board firm.Drywall Screw Phillips Bugle Head SCT Black Phosphate 4.2 x 65mm Bulk 500
The ForgeFix TechFast Masonry CSK Screw is a self-tapping, no stress alternative to plastic plugs. With an easy 2-step installation: drill a hole in substrate and screw in with power tool. These screws have a countersunk head with TORX® compatible recess. Protected by an Elementech coating, fire and corrosion resistant. Salt spray tested to 1,000 hours. Complies with EU Safety, Health and Environmental requirements. Supplied with a T20 Impact Bit.Specification: Size: 6.3 x 57mmPack Quantity: Box of 100
The DEWALT TOUGHSERIES Tape Measure allows you to conveniently measure from any angle. The double-sided blade features a Rip-Shield blade coating that provides increased durability. 16ft of extended reach allows you to easily execute long measurements without assistance. Its ultra-tough housing keeps the tape safe and secure. It's able to survive drops up 30 metres. Fitted with a magnet for easy attachment and measuring from metal surfaces.Accuracy: EC Class II.
1 x DEWALT TOUGHSERIES Tape Measure 5m/16ft (Width 32mm).
ForgeFix ForgeFast Wood Screws have a universally accepted, Torx® compatible drive. Their recessed ribs provide improved countersinking and reduced surface dust, and their reinforced countersunk necks improve holding power. The screws have a patented drill and drive thread for reduced splitting of the timber, reduced 'jacking' and spinning of joined timber, increased pull-out and a firmer fix. A sharp point provides faster bite and is capable of piercing 0.8mm steel. The screws have an 'Elementech 400' coating providing an anti-corrosive metal finish, which lasts up to 6 times longer than standard zinc coatings. The coating is environmentally friendly and does not contain Cr6+. It is Salt Spray tested to 400 hours. The screws are suitable for interior use. Every box is supplied with a Torx® compatible bit.Size: 5.0 x 20mm.Box quantity: 200.
These Forgefix single thread Coach Screws are Zinc plated for increased corrosion resistance. Their hex head enables higher torque capability when tightening, and increased speed of use with socket drivers. These Coach Screws conform to DIN 571 standards. APPLICATION:Used widely in heavier timber installations and for fixing timber to masonry. Also popular as a fixing for satellite dish installation together with a rimmed or rimless wall plug. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust which (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity. Single thread screws have been designed to offer higher pull out values and quicker insertion.
Bag of 10 ForgeFix Coach Screws Hexagon Head Single Thread ZP M10 x 40mm
These Forgefix General Purpose Pozi Screws with countersunk heads have an electro brassed finish for increased durability and to suit most internal and decorative requirements. They are versatile screws, ideal for use in and with many materials. APPLICATION:Ideal for use in many decorative installations.Can be used with various screw cover caps. The Electro brassed process of electroplating is similar to the 'Galvanised' and 'Zinc Plated' processes but with the addition of a dye. It offers an aesthetically pleasing finish that is resistant to corrosion. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. The screws' countersunk heads are designed to sink flush with substrates to leave a smooth surface finish. They have twin threads to enable an easy start when driving.General Purpose Pozi Screw Countersunk TT Electro Brass 5/8 x 6 Box 200
These Forgefix Set Screws are made from grade 8.8 steel and are zinc plated for increased resistance to corrosion. They are fully threaded and conform to DIN 933 standards.Can be used with many Nut types and washers. APPLICATION:For fastening together numerous types of material or to be fastened in to pre-tapped holes.Widely used in many engineering applications. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminum and stainless steels by their oxide layers.High Tensile Set Screw Zinc Plated M10 x 30 Bag 10
ForgeFix ForgeFast Wood Screws have a universally accepted, Torx® compatible drive. Their recessed ribs provide improved countersinking and reduced surface dust, and their reinforced countersunk necks improve holding power. The screws have a patented drill and drive thread for reduced splitting of the timber, reduced 'jacking' and spinning of joined timber, increased pull-out and a firmer fix. A sharp point provides faster bite and is capable of piercing 0.8mm steel. The screws have an 'Elementech 400' coating providing an anti-corrosive metal finish, which lasts up to 6 times longer than standard zinc coatings. The coating is environmentally friendly and does not contain Cr6+. It is Salt Spray tested to 400 hours. The screws are suitable for interior use. Every box is supplied with a Torx® compatible bit.Size: 4.0 x 25mm.Box quantity: 200.
The DEWALT Compact Series Tape Measure easily fits in your hand, tool box or pocket. The durable, coated steel blade is ideal for use in tough conditions. 3m of extended reach allows easy one person work. It also enables you to measure without blade kinking. Fitted with a finger brake for ultimate blade control, helping you to get the job done quickly and easily.Accuracy: EC Class II.
1 x DEWALT Compact Series Tape Measure 8m/26ft (Width 28mm).
These Forgefix High Tensile Hex Head Bolts are made from 8.8 grade steel. The bolts are part threaded and conform to DIN 933 standards. The hexagonal head has been designed for use with spanners or sockets and offers maximum torque when used with these tools. APPLICATION:For fastening together numerous types of material or to be fastened into pre-tapped holes. Widely used in many engineering applications. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrityHigh Tensile Bolts ZP M10 x 130 Bag 10
The ForgeFix TechFast Masonry Hex Screw is a self-tapping, no stress alternative to plastic plugs. With an easy 2-step installation: drill a hole in substrate and screw in with a power tool. These screws have an 8mm Hex head with TORX® compatible recess. Protected by an Elementech coating, fire and corrosion resistant. Salt spray tested to 1,000 hours. Complies with EU Safety, Health and Environmental requirements. Supplied with a T27 Impact Bit.Specification: Size: 6.3 x 82mmHead Type: 8mm HexPack Quantity: Box of 100
These Forgefix Multi-Purpose Pozi Screws with countersunk heads are made from A2 stainless steel. They are ideal for use in and with many materials. APPLICATIONIdeal for use in sanitary locations and in marine environments. Stainless Steel does not corrode, rust or stain with water as ordinary steel does, but despite the name it is not fully stain-proof, most notably under low oxygen, high salinity, or poor circulation environments. Stainless steel is used where both the properties of steel and resistance to corrosion are required. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. The screws' countersunk heads are designed to sink flush with substrates to leave a smooth surface finish. They have single threads, designed to offer higher pull out values and quicker insertion.Multi-Purpose Pozi Screw Countersunk ST Stainless Steel 4.0 x 40mm Box 200
Forgefix TechFast Composite Panels to Steel Hex Screws are used to join composite panels to steel frame buildings. They have a specially designed compression control thread to prevent damage and denting of panels. They are fire and corrosion resistant, protected by Elementech corrosion resistant coating, salt spray tested to 1000 hours. Complies with EU Safety, Health and Environmental requirements. They are supplied with 16mm EPDM rubber washers.These Forgefix TechFast Composite Panels to Steel Hex Screws have the following specification: Size: 5.5 x 85mmInsulation Thickness: 37-50mmPack Size: 100Drill Tip: No.5 No.5 drill tip for self-drilling in heavy gauge steel up to 12.5mm.
The ForgeFix Spectre Screws are advanced multipurpose wood screws with double countersunk heads and pozi compatible recess. They have a sawtooth thread design to prevent splitting and reamer to prevent jacking. The screws have a zinc yellow passivated finish for excellent resistance to corrosion. The zinc yellow passivation process of electroplating is similar to the 'galvanised' and 'zinc plated' processes but with the addition of a yellow dye. It offers an aesthetically pleasing finish.Specification: Size: 3.5 x 20mmThread: Fully threadedPack Quantity: Box of 200
This Forgefix fixing band is medium-duty, flexible and strong with pre-punched holes for fixing bolts and screws. It is pre-galvanised and PVC coated to provide resistance against corrosion and heat. It is easy to cut and bend. Supplied in 10m rolls in a dispensing box.Available in red, black or white. APPLICATION:Ideal for fixing, supporting cable, ducting and many more superficial installations.White Plastic Coated Pre-Galvanised Band 12mm x 0,8 x 10m Box 1
The ForgeFix Spectre Screws are advanced multipurpose wood screws with double countersunk heads and pozi compatible recess. They have a sawtooth thread design to prevent splitting and reamer to prevent jacking. The screws have a zinc yellow passivated finish for excellent resistance to corrosion. The zinc yellow passivation process of electroplating is similar to the 'galvanised' and 'zinc plated' processes but with the addition of a yellow dye. It offers an aesthetically pleasing finish.Specification: Size: 4.5 x 60mmThread: 36mm lengthPack Quantity: Box of 100
This Airmaster Tubular Heater is built with a strong steel construction and high quality powder coating, ensures the heat is evenly distributed through the heater body. Fitted with an internal thermostat. Pre-wired. An ideal heating solution where a low cost background heat is required. Comes complete with brackets for wall mounting. Specifications: Input Voltage: 240V (50Hz).Output Rating: 120W.Dimensions:: 610 x 100 x 80mm.IP Rating: IP55.Cable Length: 1m.
These Forgefix round coaxial cable clips have hardened masonry nails for increased efficiency, and which will fix into timber, block work and mortar.They are specifically designed for and will suit most TV and Satellite installations. Size: 6-7mm.Cable Clip Round Coax Brown 6-7mm Box 100
These ForgeFix ForgeFast Wood Screws have a universally accepted, Pozi compatible drive. They have 6 underhead lobes for improved countersinking and reduced surface dust, and reinforced countersunk necks which improve holding power. The screws have an anti-friction thread for reduced splitting of the timber, reduced 'jacking' and spinning of joined timber and improved drawing strength. The thread is serrated for improved pull-out and reduced torque when inserting the screw. The double cutting point allows faster drilling time and reduced clogging of wood dust and is capable of piercing 0.8mm steel. The screws have a 'Elementech 400' coating providing an anti-corrosive metal finish, which lasts up to 6 times longer than standard zinc coatings. The coating is environmentally friendly and does not contain Cr6+. It is Salt Spray tested to 400 hours. The screws are suitable for interior use.Size: 4.5 x 60 mm.Box quantity: 100.
ForgeFix ForgeFast Wood Screws have a universally accepted, Torx® compatible drive. Their recessed ribs provide improved countersinking and reduced surface dust, and their reinforced countersunk necks improve holding power. The screws have a patented drill and drive thread for reduced splitting of the timber, reduced 'jacking' and spinning of joined timber, increased pull-out and a firmer fix. A sharp point provides faster bite and is capable of piercing 0.8mm steel. The screws have an 'Elementech 400' coating providing an anti-corrosive metal finish, which lasts up to 6 times longer than standard zinc coatings. The coating is environmentally friendly and does not contain Cr6+. It is Salt Spray tested to 400 hours. The screws are suitable for interior use. Every box is supplied with a Torx® compatible bit.Size: 4.5 x 50mm.Box quantity: 200.
These Forgefix Oval Lost Head Nails are versatile and ideal for use in general joinery. The nail head virtually disappears when punched below the timber surface, making them ideal for decorative type applications. The shape of the nail helps to prevent splitting of hard or brittle timber. The nails have a 'Bright' finish, which is simply the basic raw mild steel material, without any coating or finish. APPLICATION:General cross section of joinery applications. By aligning the nail with the wood grain, splitting is reduced.Oval Lost Head Nail Bright Finish 75mm Bag Weight 250g
These Forgefix Screw Eyes are Zinc Plated for increased resistance to corrosion. They simply screw directly into timber and similar materials. Drilling a pilot hole is advisable. The screws are also suitable for use with all types of wall plugs. APPLICATIONScrew Eyes are used to attach cables, wires and twine to numerous applications. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminum and stainless steels by their oxide layers.Screw Eyes ZP 25 x 4Ga Bag 10
Forgefix TechFast Roofing Sheets to Steel Hex Screws are used for joining metal roofing panels to steel frame buildings. The screws are fire resistant and corrosion resistant. Protected by Elementech corrosion resistant coating, salt spray tested to 1000 hours. Complies with EU Safety, Health and Environmental requirements. They are supplied with 16mm EPDM rubber washers.These Forgefix TechFast Roofing Sheets to Steel Hex Screws have the following specification: Size: 5.5 x 50mmEffective Thread Length: 33mmPack Size: 100Drill Tip: No.3 No.3 drill tip for self-drilling in heavy gauge steel up to 5mm.
These ForgeFix Don Quichotte Heavy Gauge Masonry Nails have the following specification: Size: 3.5 x 80mmFinish: Zinc GalvanisedPack Quantity: Box of 100
The Roughneck Pallet Buster is ideal for demolishing all types of pallets. It’s basic functions are based on the very popular and best selling Demolition & lifting Bar but with a number of major improvements. Such as a more convenient head to handle angle and a longer handle resulting in the need to bend less for ease of operation. The jaw spacing has been increased to work on Euro pallets as well as incorporating a nail remover. Supplied with a double injected soft grip handle for comfortable use.
The Apache APKHT TWO Black Holster Trousers are an upgrade on the old reliable APKHT style. With the same great qualities, the trouser has just been modernised for additional comfort. Made from a 64% polyester, 33% cotton and 3% elastane, stretch fabric with a stretch yoke and gusset. This is to give you greater ease of movement for when you are on site all day. Double layer material on the thigh increases garment durability. It also features durable cordura branded knee pad pockets, hem and holster pockets. The elasticated waist allows the trouser to move with you. The fit has been slimmed down very slightly taking you to a regular fit. Specifications: Material Composition: 64% Polyester, 33% Cotton 3% elastane.Material Weight: 280 GSM.
FatMax® VDE Long Nose Pliers manufactured to exacting European standards individually tested to 10,000 volts and approved for working around live circuits that do not exceed 1,000 volts. The bi-material handles offer the user improved control and grip, incorporating slip guard shoulders for additional safety. They are made from a heat treated, high chrome steel forging for long life and have hand ground, induction hardened blades. DIN/ASO/ANSI compliant. Ideal for maximising grip and manoeuvring of small objects in confined spaces.Length: 200mm (8 in)
SafetySure RCD Plugs and Adaptors fully comply with BS 7071 & BS 1363. The RCD Plug & Adaptors are clam packed. No wiring needed - it simply plugs in Electrically latched - reset on power loss Technical Data: Rated voltage 230V AC 50Hz - Max operating current: 13A (3A inductive) - Rated trip current: 30mA - Typical trip speed
Choose this stop end to cap off pipework as part of a temporary or permanent installation. Part of the JG Speedfit plastic push-fit system, the 22mm stop end is easy to fit, and is demountable without tools – it can be quickly removed whenever you need to resume work or extend the system.
The stop end is really useful if you have to pause your job for any reason, or if the water needs to be turned back on overnight. It’s also very helpful when pressure-testing a system before appliances are connected.
• Caps off pipework quickly and easily
• Install in seconds by hand – just push it fully onto the pipe
• Tool-free demounting means you can resume work quickly
• Suitable for hot and cold water services, central heating systems and combi systems
• Compatible with Speedfit PEX and polybutylene plastic pipe (inserts required) and copper pipe
• Minimum operating temperature of 20 °C
• Maximum operating temperature of 105 °C
• Maximum operating pressure at minimum temperature of 12 bar
• Maximum operating pressure at maximum temperature of 3 bar
• BS EN 7291 Parts 1, 2, 3 and S
• WRAS-approved
Technical specification
Brand JG Speedfit
Colour White
Material Plastic
Manufacturer ID PSE4622W
Warranty (years) 50
Diameter (mm) 22
Pack Size 2
Fitting Type Stop End
1 x ITL Insulated 1/2in Drive Socket (6 Point) 13mm. The ITL Insulated 1/2in Drive Socket (6 Point) are made from injection moulded nylon 11, which exceeds the requirements of IEC 60900, the industry standard for live line working. In addition, they meet the requirements of Category 'C', which requires it to perform at extreme temperatures of -40°C to ;70°C, making it unique in this category. 13mm
Command™ Outdoor Decorating Clips provide an innovative solution for hanging decorations and other lightweight objects in your garden and around the outside of your home. 3M stretch-release technology provides a strong hold and removes cleanly. Hang lights and small decorations outside without causing damage to surfaces. They’re easy to apply and remove - leaving no holes, marks or sticky residue. Rearranging them is as easy as applying a Command™ Water-Resistant Refill Strip, so you can take them down, move and reuse them again and again. These all-season, all-weather strips hold strongly to a variety of surfaces including solid, hollow and painted walls, as well as other smooth materials including wood, UPVC and glass. Contains: 20 x Clear Outdoor Decorating Clips24 x Water-Resistant Refill Strips
1 x ITL Insulated Inspection Mirror. The ITL Insulated Inspection Mirror with bent hosel to help inspect hard to reach places. Made from injection moulded nylon 11, which exceeds the requirements of IEC 60900, the industry standard for live line working. In addition, this tool meets the requirements of Category 'C', which requires it to perform at extreme temperatures of -40°C to ;70°C, making it unique in this category. These insulated tools are the toughest in the market, being virtually indestructible. With a lifetime warranty on both the tool and insulation. Small
The ABUS T65AL Series Coloured Padlocks have a precision extruded, cut and drilled pure aluminium body which is light and strong, through hardened shackle, zinc plated brass lock mechanism which prevents chemical corrosion and a rust-free, 5-pin tumbler mechanism. The padlock's coloured coating is a special formula which allows you to write your name or other information using coloured pens or permanent markers. Specifiation ABUS Security Level: 5. Shackle Width: 22mm.Shackle Height: 22.5mm.Shackle Diameter: 6.5mm. Overall Width: 40mm.Overall Height: 62mm.Overall Depth: 15mm.1 x ABUS T65AL/40mm My Lock Aluminium Padlock Yellow Keyed Alike Key Reference: 6401.
The McAlpine Stainless Steel Strainer Plug is a plumbing accessory designed to prevent debris from clogging the drain pipe in sinks or basins. This strainer plug has a stainless steel construction which makes it durable and resistant to corrosion. It has a domed shape with small perforations on the surface which allows water to pass through while catching larger debris like food scraps or hair. The strainer plug is easy to install and remove, and it comes with a chain for easy retrieval. This product is suitable for use in both commercial and residential settings.
・ Mounted on Card with Hanging Slot
・ Stainless Steel Strainer Plug
・ Supplied with Rubber Seal
The Starrett TCT Stainless Steel Holesaws are ideal for cutting high alloy and stainless steels, non-ferrous light metals and reinforced fabrics at much faster speeds than is possible with a bi-metal holesaw. Tough tungsten carbide tipped teeth have a positive cutting angle which provides fast and efficient removal of chips and swarf. They have a solid one-piece construction, with complete assembly including arbor and pilot drill. A split-point drill bit allows for faster penetration and self-centring helping keep the drill on target and to prevent wandering. Fitted with ejector spring for easy core removal. Ideal for production cutting, and particularly suitable for use in drills with limited speed control. Recommended for cutting sheet metal up to 3mm (1/8in) thick.
