JG Underfloor floor clips screw easily into the insulation to secure 15mm pipe, they are best installed using a JG Underfloor fixing tool.
Secure pipe fixing floor clips
Screw down 15mm pipe clips
JG Underfloor conduit elbow allows for transition from JG Speedfit pipe from the UFH manifold pipework to conduit piping run within the floor. It can be fixed or free standing.
90ºC angle
Suitable for use with JG Speedfit PEX and polybutylene barrier pipe (inserts required) and JG Speedfit Conduit Pipe
Suitable for underfloor heating applications only
Single room underfloor heating pack for areas up to 30m2
Single zone control pack suitable for up to 30m2
Ready to plug in, pre-assembled control unit and Grundfos UPM3 circulating pump
2 coils of JG Layflat pipe (15mm x 150m)
JG Aura 230v Thermostat (programmable)
300 x pipe clips and 8 x pipe inserts (15mm)
2 JG Speedfit Equal Tees and 2 Stem Elbows (15mm)
High heat output and response
Anti-vibration mounting bracket for silent operation
Suitable for solid concrete or beam and block subfloors
This JG Underfloor Speedfit mixing valve unit is compatible with the brand's Speedfit underfloor hitting systems.
Product features
Compatible with Speedfit underfloor heating systems
Technical specifications
Brand JG Underfloor
Finish Galvanised
Length (M) 0,29
Length (mm) 290
Material Type Ductile Iron
Range speedfit
Range Name Speedfit
Range Type Wet System Underfloor Heating Valves
Weight 815.00000
Hazardous N
Body Material Ductile Iron
Dimensions (L x W x D) 290 x 220 mm
Material Ductile Iron
Supplier Product Code SPUFH1-H
Type Mixing Valve Unit
WEEE Compliant N
Width (mm) 220
JG Underfloor 240v Actuator Valve opens or closes the flow of water to an individual underfloor heating (UFH) circuit on the manifold and is controlled by a thermostat or programmer.
It also allows for independent pipe loop control via the thermostat when wired to a JG Aura wiring centre.
240v circuit actuator valve
Suitable for underfloor heating applications only
JG Speedfit x union with service valve and metal connectors (braided) for the connection to a male thread appliance, such as a tap. Ideal for bathroom basin and bath taps, the valve enables water to be isolated in the event of an emergency or for maintenance work using a ¼ turn screwdriver slot. Simply push the push-fit fitting fully onto the pipe and screw the nut onto the thread of the appliance. To demount the push-fit end, push the collet towards the body of the push-fit fitting and pull the pipe release.
The JG Speedfit x union with service valve and metal connectors (braided) is quicker and easier to install in confined spaces than traditional methods as it eliminates the need for hot works or tools. Designed, manufactured and assembled in the UK.
An alternative to hard piping to a tap or fixture
Integral service valve for isolation with 1/4 turn screwdriver slot
Flexible design makes installation hassle free
Safe flame-free installation, with no hot works, glue or flux
Braided stainless steel outer layer protects the internal feed from damage
Grip & Seal collet with stainless steel teeth and main O-Ring seal
Compatible with Speedfit PEX and polybutylene plastic pipe (inserts required) and copper pipe
Suitable for hot and cold water only (6 Bar @ 65 °C)
JG Speedfit angle service valve with tap connector for connecting fixtures to pipework. The valve enables the flow of water to a fixture to be isolated in the event of an emergency or for maintenance work using a tamperproof ¼ turn screwdriver slot. Simply push the valve fully onto the pipe and use the 90o bent nut to hand-tighten on to a side entry tap, toilet or male thread. To demount the push-fit connection end, push the collet towards the body of the push-fit fitting and pull the pipe release.
The JG Speedfit angle service valve with tap connector is quicker and easier to install in confined spaces than traditional methods as it eliminates the need for hot works or tools. Designed, manufactured and assembled in the UK.
Push-fit service valve and hand-tighten tap connector
1/4 turn isolation screwdriver slot
Safe flame-free installation, with no hot works, glue or flux
Grip & Seal collet with stainless steel teeth and main O-Ring seal
Compatible with Speedfit PEX and polybutylene plastic pipe (inserts required) and copper pipe
Suitable for hot and cold water (not suitable for central heating)
JG Speedfit straight service valve with tap connector for the connection of plastic and copper pipe. Using an integrated handle, the valve allows for isolation of fixtures (taps, bath taps and WCs) and appliances (washing machines and dishwashers) for maintenance or installation.
To connect simply push the JG Speedfit service valve with tap connector fully onto the pipe and screw up to the fixture to the threaded connection. To demount the connection, pull the collet towards the body of the push-fit fitting and pull the pipe to release. Designed, manufactured and assembled in the UK.
Push-fit service valve and hand-tighten tap connector
Integrated ¼ turn handle instantly isolates water
Safe flame-free installation, with no hot works, glue or flux
Grip & Seal collet with stainless steel teeth and main O-Ring seal
Compatible with Speedfit PEX and polybutylene plastic pipe (inserts required) and copper pipe
Suitable for hot and cold water (not suitable for central heating)
JG Speedfit x union nut flexi hose with service valve (white PVC) for the connection to a male thread appliance, such as a tap. The white PVC hose material significantly reduces the hose ‘kinking’ and makes the product easier to clean. Ideal for bathroom basin and bath taps, the valve enables water to be isolated in the event of an emergency or for maintenance work using an easy to operate integrated handle.
Simply push the JG Speedfit x union nut flexi hose with service valve (white PVC) fully onto the pipe and screw the nut onto the thread of the appliance. To demount the push-fit end, push the collet towards the body of the push-fit fitting and pull the pipe release. The push-fit fitting is quicker and easier to install in confined spaces than traditional methods as it eliminates the need for hot works or tools. Designed, manufactured and assembled in the UK.
An alternative to hard piping to a tap or fixture
Integral service valve for isolation with an easy to operate handle
Flexible design makes installation hassle free
Safe flame-free installation, with no hot works, glue or flux
White PVC design stops the pipe kinking and makes cleaning easier
Grip & Seal collet with stainless steel teeth and main O-Ring seal
Compatible with Speedfit PEX and polybutylene plastic pipe (inserts required) and copper pipe
Suitable for hot and cold water only (6 Bar @ 65 °C)
JG Speedfit x union nut flexi hose (white PVC) for the connection to a male thread appliance, such as a tap. The PVC hose material significantly reduces the hose ‘kinking’ and makes the product easier to clean. Simply push the push-fit fitting fully onto the pipe and screw the nut onto the thread of the appliance. To demount the push-fit end, push the collet towards the body of the push-fit fitting and pull the pipe release.
The JG Speedfit x union nut flexi hose (white PVC) is quicker and easier to install in confined spaces than traditional methods as it eliminates the need for hot works or tools. Designed, manufactured and assembled in the UK.
An alternative to hard piping to a tap or fixture
Flexible design makes installation hassle free
Safe flame-free installation, with no hot works, glue or flux White PVC design stops the pipe kinking and makes cleaning easier
Grip & Seal collet with stainless steel teeth and main O-Ring seal
Compatible with Speedfit PEX and polybutylene plastic pipe (inserts required) and copper pipe
Suitable for hot and cold water only (6 Bar @ 65 °C)
JG Speedfit x Speedfit flexi hose (white PVC) for the connection of plastic or copper pipe. The white PVC hose material significantly reduces the hose ‘kinking’ and makes the product easier to clean. Simply push the push-fit fitting fully onto the pipe. To demount the connection, push the collet towards the body of the push-fit fitting and pull the pipe release.
The JG Speedfit x Speedfit flexi hose (white PVC) is quicker and easier to install in confined spaces than traditional methods as it eliminates the need for hot works or tools. Designed, manufactured and assembled in the UK.
An alternative to hard piping to a tap or fixture
Flexible design makes installation hassle free
Safe flame-free installation, with no hot works, glue or flux White PVC design stops the pipe kinking and makes cleaning easier
Grip & Seal collet with stainless steel teeth and main O-Ring seal
Compatible with Speedfit PEX and polybutylene plastic pipe (inserts required) and copper pipe
Suitable for hot and cold water only (6 Bar @ 65 °C)
JG Speedfit x union nut flexi hose (white PVC) for the connection to a male thread appliance, such as a tap. The PVC hose material significantly reduces the hose ‘kinking’ and makes the product easier to clean. Simply push the push-fit fitting fully onto the pipe and screw the nut onto the thread of the appliance. To demount the push-fit end, push the collet towards the body of the push-fit fitting and pull the pipe release.
The JG Speedfit x union nut flexi hose (white PVC) is quicker and easier to install in confined spaces than traditional methods as it eliminates the need for hot works or tools. Designed, manufactured and assembled in the UK.
An alternative to hard piping to a tap or fixture
Flexible design makes installation hassle free
Safe flame-free installation, with no hot works, glue or flux
White PVC design stops the pipe kinking and makes cleaning easier
Grip & Seal collet with stainless steel teeth and main O-Ring seal
Compatible with Speedfit PEX and polybutylene plastic pipe (inserts required) and copper pipe
Suitable for hot and cold water only (6 Bar @ 65 °C)
JG Speedfit x union nut flexi hose (white PVC) for the connection to a male thread appliance, such as a tap. The PVC hose material significantly reduces the hose ‘kinking’ and makes the product easier to clean. Simply push the push-fit fitting fully onto the pipe and screw the nut onto the thread of the appliance. To demount the push-fit end, push the collet towards the body of the push-fit fitting and pull the pipe release.
The JG Speedfit x union nut flexi hose (white PVC) is quicker and easier to install in confined spaces than traditional methods as it eliminates the need for hot works or tools. Designed, manufactured and assembled in the UK.
An alternative to hard piping to a tap or fixture
Flexible design makes installation hassle free
Safe flame-free installation, with no hot works, glue or flux White PVC design stops the pipe kinking and makes cleaning easier
Grip & Seal collet with stainless steel teeth and main O-Ring seal
Compatible with Speedfit PEX and polybutylene plastic pipe (inserts required) and copper pipe
Suitable for hot and cold water only (6 Bar @ 65 °C)
JG Speedfit x hand tighten flexi hose (white PVC) for the connection to a male thread appliance, such as a Tap. The white PVC hose material significantly reduces hose ‘kinking’ and makes the product easier to clean.
On one end the hose features a push-fit connection for a supply pipe. On the other end there is a plastic nut which can be hand tightened on to a tap or male thread. To demount the push-fit end, simply push the collet towards the body of the push-fit fitting and pull the pipe to release.
The JG Speedfit x hand tighten flexi hose (white PVC) is quicker and easier to install in confined spaces than traditional methods as it eliminates the need for hot works or tools. Designed, manufactured and assembled in the UK.
An alternative to hard piping to a tap or fixture
Flexible design makes installation hassle free
Safe flame-free installation, with no hot works, glue or flux
White PVC design stops the pipe kinking and makes cleaning easier
Grip & Seal collet with stainless steel teeth and main O-Ring seal
Compatible with Speedfit PEX and polybutylene plastic pipe (inserts required) and copper pipe
Suitable for hot and cold water only (6 Bar @ 65 °C)
JG Speedfit x hand tighten flexi hose (white PVC) for the connection to a male thread appliance, such as a Tap. The white PVC hose material significantly reduces hose ‘kinking’ and makes the product easier to clean.
On one end the hose features a push-fit connection for a supply pipe. On the other end there is a plastic nut which can be hand tightened on to a tap or male thread. To demount the push-fit end, simply push the collet towards the body of the push-fit fitting and pull the pipe to release.
The JG Speedfit x hand tighten flexi hose (white PVC) is quicker and easier to install in confined spaces than traditional methods as it eliminates the need for hot works or tools. Designed, manufactured and assembled in the UK.
An alternative to hard piping to a tap or fixture
Flexible design makes installation hassle free
Safe flame-free installation, with no hot works, glue or flux
White PVC design stops the pipe kinking and makes cleaning easier
Grip & Seal collet with stainless steel teeth and main O-Ring seal
Compatible with Speedfit PEX and polybutylene plastic pipe (inserts required) and copper pipe
Suitable for hot and cold water only (6 Bar @ 65 °C)
JG Speedfit x union nut flexi hose (white PVC) for the connection to a male thread appliance, such as a tap. The PVC hose material significantly reduces the hose ‘kinking’ and makes the product easier to clean. Simply push the push-fit fitting fully onto the pipe and screw the nut onto the thread of the appliance. To demount the push-fit end, push the collet towards the body of the push-fit fitting and pull the pipe release.
The JG Speedfit x union nut flexi hose (white PVC) is quicker and easier to install in confined spaces than traditional methods as it eliminates the need for hot works or tools. Designed, manufactured and assembled in the UK.
An alternative to hard piping to a tap or fixture
Flexible design makes installation hassle free
Safe flame-free installation, with no hot works, glue or flux White PVC design stops the pipe kinking and makes cleaning easier
Grip & Seal collet with stainless steel teeth and main O-Ring seal
Compatible with Speedfit PEX and polybutylene plastic pipe (inserts required) and copper pipe
Suitable for hot and cold water only (6 Bar @ 65 °C)
JG Speedfit x union nut flexi hose (white PVC) for the connection to a male thread appliance, such as a tap. The PVC hose material significantly reduces the hose ‘kinking’ and makes the product easier to clean. Simply push the push-fit fitting fully onto the pipe and screw the nut onto the thread of the appliance. To demount the push-fit end, push the collet towards the body of the push-fit fitting and pull the pipe release.
The JG Speedfit x union nut flexi hose (white PVC) is quicker and easier to install in confined spaces than traditional methods as it eliminates the need for hot works or tools. Designed, manufactured and assembled in the UK.
An alternative to hard piping to a tap or fixture
Flexible design makes installation hassle free
Safe flame-free installation, with no hot works, glue or flux White PVC design stops the pipe kinking and makes cleaning easier
Grip & Seal collet with stainless steel teeth and main O-Ring seal
Compatible with Speedfit PEX and polybutylene plastic pipe (inserts required) and copper pipe
Suitable for hot and cold water only (6 Bar @ 65 °C)
JG Speedfit monobloc mixer flexi hose (white PVC) that connects plastic or copper pipe onto a monobloc mixer. The white PVC hose material significantly reduces hose ‘kinking’ and makes the product easier to clean.
On one end the hose features a push-fit connection for a supply pipe. On the other end there is a monobloc connection which can be installed on to a monobloc tap. To demount the push-fit end, push the collet towards the body of the push-fit fitting and pull the pipe release.
The JG Speedfit monobloc mixer flexi hose (white PVC) is quicker and easier to install in confined spaces than traditional methods as it eliminates the need for hot works or tools. Designed, manufactured and assembled in the UK.
An alternative to hard piping to a tap or fixture
Flexible design makes installation hassle free
Safe flame-free installation, with no hot works, glue or flux
White PVC design stops the pipe kinking and makes cleaning easier
Grip & Seal collet with stainless steel teeth and main O-Ring seal
Compatible with Speedfit PEX and polybutylene plastic pipe (inserts required) and copper pipe
Suitable for hot and cold water only (6 Bar @ 65 °C)
JG Speedfit wing back plate elbow push-fit fitting for the quick and secure installation of bib style taps. Simply push the push-fit fitting fully onto the pipe and twist the plastic nut clockwise to lock in place. To demount the connection, unlock the nut by hand and push the collet towards the body of the push-fit fitting and pull the pipe to release.
The JG Speedfit wing back plate elbow is quicker and easier to install in confined spaces than traditional methods as it eliminates the need for hot works or tools. Designed, manufactured and assembled in the UK.
Instant push-fit connection
Install and demount in seconds without tools
Safe flame-free installation, with no hot works, glue or flux
Grip & Seal collet with stainless steel teeth and main O-Ring seal
Twist & Lock mechanism secures fitting and adds compression
Non-toxic, resists corrosion and no scale build-up
Compatible with MDPE pipes (inserts required)
Suitable for cold water use only
