The Faithfull Pocket Portable Multimeter is a compact unit contained within a flip open case. It is ideal for performing many checks used in radio and electronic testing, car electrics, household appliances, portable tools and similar equipment. With a 3.1/2 digit LCD display, this multimeter is suitable for measuring DC and AC voltage, DC and AC current, resistance, diode and continuity. It features data hold and polarity indication. It is easy to operate and carry, and is an ideal measurement tool. Supplied with batteries, test leads and user manual.Specification: AC Voltage: 200-250VDC Voltage: 2V/20V/200V/300VDC Current: 200mAResistance: 2k½/20k½/200k½/2000k½Diode Check: ~2.5VContinuity: > 30½Cat II 250VPower: 2 x 1.5V LR44 batteries (supplied)Dimensions: 114 x 55 x 22mmWeight: approx. 100g (including battery)
The Faithfull Sound Level Meter is a compact digital tool for recording noise levels. It can be used to measure the sound level in all kinds of environments, such as factories, schools, offices, traffic, roads etc.Features include over-range indication, Max./Min. measurement mode, data hold, low battery indication, auto power-off and more. Sound level meters are instruments designed to react to the noise much like the human ear. The measurements taken by sound level meters are compared to known standards to identify whether the noise level could have a detrimental effect on humans located near the noise source.It is supplied with a removable wind noise reducing cap, batteries and user manual.Display: 4 digits LCD with backlightFrequency Weighting: AMeasuring Range: 30 dB - 130 dBFrequency Range: 30Hz~8kHzResolution: 0.1 dBAccuracy: ±1.5 dBOver-range Indicator: "OL" appears when the measured value is higher than the upper limit of the measuring range. "LO" appears when the measured value is lower than the lower limit of the measuring range.MAX./MIN. Measurement ModeTime Weighting: FAST mode and SLOW mode Microphone: Omni-directional Condenser MicrophoneOperating Altitude: <2000m above sea levelOperating Environment: 0-40°C, 20%-30%RHStorage Environment: -10°C to 50°C, <90%RHPower: 3 x 1.5V AAA batteries (supplied)Size: 160 x 54 x 32mmWeight: approx. 110g (including battery)
The Faithfull Voltage Detector Stick is a non-contact AC voltage detector for detecting 5-1000V AC voltage. It is ideal for testing sockets and wires, and for detecting break points in a live wire.When AC voltage is detected, the indicator LED will flash red and the built-in buzzer will sound short beeps. The rotary power switch can be used to adjust the unit's detection sensitivity and an illumination function is provided for use in dark places. The detector's LED will flash red periodically to indicate there is sufficient battery power left. The casing features a pocket clip to help keep the unit close to hand.Supplied with batteries and user manual. Specification: Voltage Detecting Range: 5-1000V ACFrequency Range: 50~400HzSafety Category: CAT IV 1000VPower: 2 x 1.5V AAA batteries (supplied)Size: 154 x 32 x 28mmWeight: approx. 50g (including batteries)
The Marshalltown ProSkim® Telescopic Handle has a lightweight but strong tubular aluminium construction. Fitted with a comfortable, non-slip contoured plastic handle. It extends between 100cm and 190cm, making it perfect for working on taller walls and ceilings. Designed to fit the ProSkim® Handle Bracket (M/TMSKIMBRKT).
The Monument Drain Down Hose is designed to lay flat when draining down a central heating system. Unlike standard hose pipe, when uncoiled the hose lays flat, allowing water to flow with gravity. Complete with a hose clip to affix to the drain off cock. The silicone rubber hose can be coiled neatly with hook & loop fasteners for storing/transporting. Specification: Length: 15mInternal diameter: 12mmOutside diameter: 19mm
This Norbar Industrial Torque Wrench has the following specification: Drive: 3/4in SquareRange: 120-600Nm (100-450 lbf·ft)Ratchet Type: Push ThroughLength: 954mmWeight: 5.95kg
This Norbar Industrial Torque Wrench has the following specification: Drive: 1in SquareRange: 120-600Nm (100-450 lbf·ft)Ratchet Type: Push ThroughLength: 954mmWeight: 5.95kg
This Norbar Industrial Torque Wrench has the following specification: Drive: 3/4in SquareRange: 200-800Nm (150-600 lbf·ft)Ratchet Type: Push ThroughLength: 1,214mmWeight: 6.65kg
This Norbar Industrial Torque Wrench has the following specification: Drive: 1in SquareRange: 200-800Nm (150-600 lbf·ft)Ratchet Type: Push ThroughLength: 1,214mmWeight: 6.65kg
ROCOL RAPIDSEAL is a fluorescent yellow compound for use as a thread sealant on industrial metal pipework (including stainless steel) up to 3in diameter. Rapid-cure speed minimises down time in breakdown or repair situations It precision applicator improves working conditions and minimises waste. With a thread locking action that eliminates vibration induced loosening. Can replace traditional paste/hemp combinations. Suitable for use with stainless steel, glycol, etc. Meets requirements of EN 751 - 1. NSF P1 registered. Solvent free.
The IRWIN® STRAIT-LINE® Speedline™ Reel has the following features: _ Large, Easy Fill & Lock top for quick chalk fill and easy access to reel internals_ 3:1 Gear ratio rewinds line 3x faster than traditional chalk reels Supplied with a red chalk value pack 113g and hanging level.
Bahco ERGO™ Insulated Bent Nose Pliers have half-round serrated jaws for gripping flat and round material. The hardened cutting edges are suitable for cutting soft and hard wire. Made from high-performance alloy steel with a phosphate finish and anti-corrosion treated. Fitted with two-component ERGO™ insulated handles (thermoplastic surface on a tough polypropylene base) to provide superior grip. Suitable for working on live equipment up to 1,000V in compliance with IEC 60900. Every tool is tested at 10,000V for 10 seconds at the end of the manufacturing process. Developed according to the scientific ERGO™ process. Conform to ISO 5745, IEC 60900 standards. Specification: Length: 160mm (6.1/4in)Cutting Capacity: Copper 2.5-3mm, Iron 1.4mm, Iron Alloy 1.6mm
Bahco ERGO™ Insulated Pliers with 45° bent, half-round serrated jaws for gripping flat and round material. The hardened cutting edges are suitable for cutting soft and hard wire. Made from high-performance alloy steel with a phosphate finish and anti-corrosion treated. Fitted with two-component ERGO™ insulated handles (thermoplastic surface on a tough polypropylene base) to provide superior grip. Suitable for working on live equipment up to 1,000V in compliance with IEC 60900. Every tool is tested at 10,000V for 10 seconds at the end of the manufacturing process. Developed according to the scientific ERGO™ process. Conform to ISO 5745, IEC 60900 standards. Specification: Length: 200mm (8in)Cutting Capacity: Copper 3mm, Iron 1.8mm, Iron Alloy 1.6mm
1 x Bahco 2430S ERGO™ Insulated Long Nose Pliers 160mm (6.1/4in) Cutting Capacity; Copper 3mm, Iron 1.8mm, Iron Alloy 1.6mm Bahco ERGO™ Insulated Long Nose Pliers have half-round serrated jaws for gripping flat and round material. The hardened cutting edges are suitable for cutting soft and hard wire. Made from high-performance alloy steel with a phosphate finish and anti-corrosion treated. Fitted with two-component ERGO™ insulated handles (thermoplastic surface on a tough polypropylene base) to provide superior grip. Suitable for working on live equipment up to 1,000V in compliance with IEC 60900. Every tool is tested at 10,000V for 10 seconds at the end of the manufacturing process. Developed according to the scientific ERGO™ process. Conform to ISO 5745, IEC 60900 standards.
These Bahco 2430S ERGO™ Insulated Long Nose Pliers have the following specification: Length: 200mm (8in)Cutting Capacity: Copper 3mm, Iron 1.8mm, Iron Alloy 1.6mm Bahco ERGO™ Insulated Long Nose Pliers have half-round serrated jaws for gripping flat and round material. The hardened cutting edges are suitable for cutting soft and hard wire. Made from high-performance alloy steel with a phosphate finish and anti-corrosion treated. Fitted with two-component ERGO™ insulated handles (thermoplastic surface on a tough polypropylene base) to provide superior grip. Suitable for working on live equipment up to 1,000V in compliance with IEC 60900. Every tool is tested at 10,000V for 10 seconds at the end of the manufacturing process. Developed according to the scientific ERGO™ process. Conform to ISO 5745, IEC 60900 standards.
1 x Bahco 2628S ERGO™ Insulated Combination Pliers 160mm (6.1/4in) Cutting Capacity; Iron Alloy 2mm, Piano Wire 1.8mm Bahco ERGO™ Insulated Combination Pliers have a special head design for better accessibility and hardened cutting edges for cutting soft and hard wire. Its gripping surfaces are particularly suited for flat and round material. Made from high-performance alloy steel with a phosphate finish and anti-corrosion treated. Fitted with two-component ERGO™ insulated handles (thermoplastic surface on a tough polypropylene base) to provide superior grip. Suitable for working on live equipment up to 1,000V in compliance with IEC 60900. Every tool is tested at 10,000V for 10 seconds at the end of the manufacturing process. Developed according to the scientific ERGO™ process. Conform to ISO 5745, IEC 60900 standards.
1 x Bahco 2628S ERGO™ Insulated Combination Pliers 180mm (7in) Cutting Capacity; Iron Alloy 2.5mm, Piano Wire 2.0mm Bahco ERGO™ Insulated Combination Pliers have a special head design for better accessibility and hardened cutting edges for cutting soft and hard wire. Its gripping surfaces are particularly suited for flat and round material. Made from high-performance alloy steel with a phosphate finish and anti-corrosion treated. Fitted with two-component ERGO™ insulated handles (thermoplastic surface on a tough polypropylene base) to provide superior grip. Suitable for working on live equipment up to 1,000V in compliance with IEC 60900. Every tool is tested at 10,000V for 10 seconds at the end of the manufacturing process. Developed according to the scientific ERGO™ process. Conform to ISO 5745, IEC 60900 standards.
1 x Bahco 2628S ERGO™ Insulated Combination Pliers 200mm (8in) Cutting Capacity; Iron Alloy 3mm, Piano Wire 2.5mm Bahco ERGO™ Insulated Combination Pliers have a special head design for better accessibility and hardened cutting edges for cutting soft and hard wire. Its gripping surfaces are particularly suited for flat and round material. Made from high-performance alloy steel with a phosphate finish and anti-corrosion treated. Fitted with two-component ERGO™ insulated handles (thermoplastic surface on a tough polypropylene base) to provide superior grip. Suitable for working on live equipment up to 1,000V in compliance with IEC 60900. Every tool is tested at 10,000V for 10 seconds at the end of the manufacturing process. Developed according to the scientific ERGO™ process. Conform to ISO 5745, IEC 60900 standards.
Bahco 396-INS Folding Insulation Saw with super sharp wavy toothing (WT) for a smooth and clean cut. Cuts insulation materials: glass wool, stone wool, etc. Ideal for use when space is limited. Fitted with a strong handle and a soft, non-slip grip for increased comfort and control. There is also a safety lock on the blade that can be used in the opened and closed position. Specification: Blade Length: 175mmFolded Length: 230mm
1 x Bahco 428 Curved Fibreglass Claw Hammer 454g (16oz). The Bahco 428 Curved Claw Hammer has an octagonal neck and a brightly polished round head. Fitted with a fibreglass handle for maximum shock absorption and a comfortable black hand grip. The shaft is painted a bright orange, making it easier to find in a toolbox.
1 x Bahco 428 Curved Fibreglass Claw Hammer 570g (20oz). The Bahco 428 Curved Claw Hammer has an octagonal neck and a brightly polished round head. Fitted with a fibreglass handle for maximum shock absorption and a comfortable black hand grip. The shaft is painted a bright orange, making it easier to find in a toolbox.
1 x Bahco ERGO™ Slim VDE Insulated Phillips Screwdriver PH1 x 80mm. Bahco ERGO™ Slim VDE Insulated Screwdrivers with slim blades (reduced blade diameter) for Phillips head screws. Blades are 30% slimmer than regular insulated blades for better accessibility. Suitable for work on live equipment, up to 1,000V. Its high-quality blade insulation is moulded directly onto the blade. The phosphate finish tip provides higher accuracy, a precise fit and no flaking. Fitted with a 3-component handle for maximum user comfort. The soft material with a ridged surface provides superior grip and greater force transmission. It's easy to choose the right tip with the colour coded handle and permanent symbol on the domed end. A flat face prevents the screwdriver from rolling away. There is also an integrated hanging hole for easy storage. Screwdriver developed according to the scientific ERGO™ process. Individually inspected and manufactured according to IEC 60900, tested in a water bath at 10,000V. Conforms to: ISO 2380/DIN 5264.
1 x Bahco ERGO™ Slim VDE Insulated Phillips Screwdriver PH2 x 100mm. Bahco ERGO™ Slim VDE Insulated Screwdrivers with slim blades (reduced blade diameter) for Phillips head screws. Blades are 30% slimmer than regular insulated blades for better accessibility. Suitable for work on live equipment, up to 1,000V. Its high-quality blade insulation is moulded directly onto the blade. The phosphate finish tip provides higher accuracy, a precise fit and no flaking. Fitted with a 3-component handle for maximum user comfort. The soft material with a ridged surface provides superior grip and greater force transmission. It's easy to choose the right tip with the colour coded handle and permanent symbol on the domed end. A flat face prevents the screwdriver from rolling away. There is also an integrated hanging hole for easy storage. Screwdriver developed according to the scientific ERGO™ process. Individually inspected and manufactured according to IEC 60900, tested in a water bath at 10,000V. Conforms to: ISO 2380/DIN 5264.
1 x Bahco ERGO™ Slim VDE Insulated Pozidriv Screwdriver PZ1 x 80mm. Bahco ERGO™ Slim VDE Insulated Screwdrivers with slim blades (reduced blade diameter) for Pozidriv head screws. Blades are 30% slimmer than regular insulated blades for better accessibility. Suitable for work on live equipment, up to 1,000V. Its high-quality blade insulation is moulded directly onto the blade. The phosphate finish tip provides higher accuracy, a precise fit and no flaking. Fitted with a 3-component handle for maximum user comfort. The soft material with a ridged surface provides superior grip and greater force transmission. It's easy to choose the right tip with the colour coded handle and permanent symbol on the domed end. A flat face prevents the screwdriver from rolling away. There is also an integrated hanging hole for easy storage. Screwdriver developed according to the scientific ERGO™ process. Individually inspected and manufactured according to IEC 60900, tested in a water bath at 10,000V. Conforms to: ISO 2380/DIN 5264.
1 x Bahco ERGO™ Slim VDE Insulated Pozidriv Screwdriver PZ2 x 80mm. Bahco ERGO™ Slim VDE Insulated Screwdrivers with slim blades (reduced blade diameter) for Pozidriv head screws. Blades are 30% slimmer than regular insulated blades for better accessibility. Suitable for work on live equipment, up to 1,000V. Its high-quality blade insulation is moulded directly onto the blade. The phosphate finish tip provides higher accuracy, a precise fit and no flaking. Fitted with a 3-component handle for maximum user comfort. The soft material with a ridged surface provides superior grip and greater force transmission. It's easy to choose the right tip with the colour coded handle and permanent symbol on the domed end. A flat face prevents the screwdriver from rolling away. There is also an integrated hanging hole for easy storage. Screwdriver developed according to the scientific ERGO™ process. Individually inspected and manufactured according to IEC 60900, tested in a water bath at 10,000V. Conforms to: ISO 2380/DIN 5264.
