The ForgeFast Decking Screws Countersunk TORX® T25 are suitable for fixing into softwood or hardwood. They have a deep TORX® compatible insert that reduces cam-out, provides higher torque levels and a firmer drive. Its super sharp tip gives immediate bite from the very first turn and the recessed under-head ribs provide superb countersinking. A patented self-drilling thread removes the need to pre-drill the timber and reduces the probability of splitting, even when screwing close to the edge. Protected by elementech 2000 surface treatment which provides corrosion resistance up to 30 times longer than some standard zinc coated screws. They are highly resistant to pull out, they can flex by up to 35mm, reducing likelihood of screw shearing when used in flexible materials. CE approved for use in load-bearing timber construction.ForgeFast Decking Screws Countersunk TORX® T25 Size: 4.5 x 50mmPack Size: Tub of 600Finish: Green elementech 2000
These Forgefix Phillips, twin fine thread Drywall Screws have a zinc plated finish for increased durability. The screws come complete with a Phillips No.2 insert bit. Their Bugle Head allows the screw to sink effortlessly into the dry lining eithout the need for countersinking, which in turn minimises the damage to the surface. APPLICATION:Designed for fitting dry linings to studding. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminum and stainless steels by their oxide layers. The Phillips screw has four simple tapered slots. It is designed so that a Phillips tip screwdriver can turn a Phillips screw with increasing torque. When the torque gets to be too strong for the tip then the screwdriver tip winds itself out of the screw thus preventing over-tightening and or damage to the screw head. Fine thread screws have an extremely sharp point which not only pierces the plasterboard skin but will also allow the screw to drill through thin steel base structures.Drywall Screw Phillips Bugle Head TFT ZP 3.5 x 42mm Bulk 1000
These Forgefix high-low thread Concrete Frame Screws are Zinc Yellow Passivated for increased resistance to corrosion. They offer a virtually stress free fixing, allowing close to edge applications. They are through-fixing, eliminating the need for marking and re-positioning when fixing batons etc. The Torx compatible head of the screw enables increased torque control. APPLICATION: Extremely popular fixing for window and door frames. Also now used as a versatile fixing for many applications in DIY, Joinery, Plumbing and Electrical trades. The Zinc Yellow Passivation process of electroplating is similar to the 'Galvanised' and 'Zinc Plated' processes but with the addition of a yellow dye. It offers an aesthetically pleasing finish, whilst having excellent resistance to corrosion. By design, Torx compatible head screws resist cam-out much better than Phillips or Slotted screws. Where Phillips heads were designed to cause the driver to cam out, to prevent over-tightening, Torx compatible heads were designed to prevent it and to achieve a desired torque consistently. Torx compatible head sizes are described using the capital letter 'T', followed by a number. A smaller number corresponds to a smaller point-to-point dimension of the screw head. Only the proper driver can drive a specific head size without risk of ruining the driver or screw. High-Low Thread screws have an excellent holding power in wood due to their alternating high and low thread heights.Concrete Frame Screw Torx High-Low Thread ZYP 7.5 x 72mm. Bag's of 10 supplied with Bolts only.
These Panel Pins are ideal for lightweight and decorative tasks. For corrosion resistance, the pins are sheradised. The shape of the pins helps to reduce splitting in hard or brittle timber. APPLICATION:General cross section of joinery applications such as fixing decorative timber mouldings. Sheradisation is the process of choice for fixings or fasteners that require long-term corrosion resistance. The sheradised finish is a thermal diffusion process, in which Zinc powder is vaporised and diffuses into the surface of the fastener or fixing to form a sacrificial corrosion protective Zinc /Iron alloy coating which dramatically increases the nails' durability.Panel Pin Sheradised 30mm Bag Weight 500g
These Forgefix High Tensile Hex Head Bolts are made from 8.8 grade steel. The bolts are part threaded and conform to DIN 933 standards. The hexagonal head has been designed for use with spanners or sockets and offers maximum torque when used with these tools. APPLICATION:For fastening together numerous types of material or to be fastened into pre-tapped holes. Widely used in many engineering applications. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrityHigh Tensile Bolts ZP M6 x 60 Bag 10
The ForgeFast Elite Performance Pozi Exterior Wood Screw features the Elementech 2000 Coating System which has been developed to provide increased corrosion resistance when installed in treated and untreated wood. A 2,000 hour salt spray test rating simulates exterior, coastal construction environments and ensures Elite Performance in all weather conditions in both commercial and residential applications. The advanced thread technology and POZI recess are designed to provide faster and easier installation with no pre-drilling required. A double cutting point reduces splitting and drive time and is capable of penetrating 0.8mm steel. A firmer fix with reduced drive torque and improved pull-out provided by a serrated cutting thread. Anti-friction thread prevents 'jacking' and rotation of adjoining timbers whilst reducing splitting. Improved holding power from reinforced countersunk neck. Improved countersinking from 6 angled lobes. Universally accepted POZI® compatible head. CE approved for use in load-bearing timber construction. Elementech 2000 surface coating provides corrosion resistance. A Non-Cr, Cr3+, yellow/zinc surface is environmentally friendly. Lasts up to 30 times longer than standard zinc screw protective coating. Suitable for exterior use.ForgeFast Exterior Elite 2000 Pozi Compatible Wood Screw 4 x 50mm Box 300
These Forgefix General Purpose Pozidrive Screws with Countersunk heads are zinc plated for increased durability. They are an extremely popular general purpose screw, and suitable for use in and with many materials. APPLICATION:Ideal for use in many ironmongery, electrical and plumbing applications.Can be used with various screw cover caps. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminium and stainless steels by their oxide layers. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. The countersunk head is designed to sink flush with substrates to leave a smooth surface finish. They have twin threads, which enable an easy start when driving. Imperial Size > MetricNo.4 = 3.0mm, No.6 = 3.5mm, No.7 = 3.9mmNo.8= 4.0mm, No.10 = 5.0mm, No.12 = 6.0mmGeneral Purpose Pozi Screw Countersunk TT ZP 1 x 12 Box 200
These Forgefix Carriage Bolts are Zinc Plated, and ideal for timber to timber joining. They come complete with a hex nut and are fully threaded to 100mm. Also known as 'Cup Square Hex Bolts', the square underneath the Cup stops rotation of the bolt when tightening. Conform to DIN 603 and DIN 934 standards. Available in a comprehensive range of sizes to suit most applications. APPLICATIONUsed mainly for fastening timber to timber and is extensively used for timber joist construction in house building and numerous decking applications. A Carriage Bolt, also known as a Coach Bolt or as a ‘Fully Threaded Cup Square Hex Bolt’, has a domed or countersunk head, and the shank is topped by a short square section under the head. The square section grips into the part being fixed (typically wood), preventing the bolt from turning when the nut is tightened. A rib neck Carriage Bolt has several longitudinal ribs instead of the square section, to grip into a metal part being fixed. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminium and stainless steels by their oxide layers.Carriage Bolt & Nut ZP M10 x 240 Bag 10
Forgefix TechFast Timber to Steel CSK/Wing Screws are used to join timber to steel frame buildings. The screws are fitted with breakaway wings that create a clearance hole to protect thread from engaging timber when drilling through. Breakaway wings will ream a hole, then break-off when they contact the metal surface to be drilled. The thread will then engage with metal. They have a TORX® compatible insert for a higher transmission of power. With improved countersinking from recessed ribs. Fire and corrosion resistant. Complies with EU Safety, Health and Environmental requirements.These Forgefix TechFast Timber to Steel CSK/Wing Screws have the following specification: Size: 5.5 x 40mmClamping Thickness: 20mmEffective Thread Length: 19mmPack Size: 100Drill Tip: No.3 No.3 drill tip for self-drilling heavy gauge steel up to 5mm.
These Forgefix Multi-Purpose Pozi Screws with countersunk heads have a zinc finish for increased durability. The screws are immensely popular and versatile, and used in all trades including joinery, electrical and plumbing. Also widely used in DIY applications. APPLICATIONSuitable for use with many materials including PVCu, Timber, Chipboard, MDF, and other similar types. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminium and stainless steels by their oxide layers. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. The countersunk head is designed to sink flush with substrates to leave a smooth surface finish. They have single threads, designed to offer higher pull out values and quicker insertion.Specifications: Size: 5 x 100mm.Box quantity: 100.
Forgefix Hex Head Lightning Bolts provide a virtually stress-free fixing for close to edge applications. They are self-threading and allow quick and easy installation of most masonry fixing applications. They can simply be screwed into a pre-drilled hole, without the need for a sleeve or plug. The bolts are through-fixing, eliminating the need for marking and re-positioning. They have a high load capacity due to the thread interlocking into the base material. The bolts have an 'Elementech' coating for superior anti-corrosion, which has been salt spray tested to 1,000 hours. Applications: Widely used for fixing battens, balustrades, handrails, racking and holding down machinery, plus many more installation applications. Suitable for most masonry substrates including concrete and brickwork but also for hollow block or bricks due to the nature of the thread type anchoring along the total length of the fixing.Specifications: Size: M10 x 150mm.Pack quantity: 10.
Forgefix TechFast Roofing Sheet to Steel Hex Light Duty Screws are used for joining metal roofing panels to steel frame buildings. The screws are fire resistant and corrosion resistant. Protected by Elementech corrosion resistant coating, salt spray tested to 1000 hours. Complies with EU Safety, Health and Environmental requirements. Supplied without washer.These Forgefix TechFast Roofing Sheet to Steel Screws have the following specification: Size: 5.5 x 100mmEffective Thread Length: 81mmHead Type: 8mm HexPack Size: 100Drill Tip: No.5 No.5 drill tip for self-drilling in heavy gauge steel up to 12.5mm.
These Forgefix Multi-Purpose Pozi Screws with countersunk heads are made from A2 stainless steel. They are ideal for use in and with many materials. APPLICATIONIdeal for use in sanitary locations and in marine environments. Stainless Steel does not corrode, rust or stain with water as ordinary steel does, but despite the name it is not fully stain-proof, most notably under low oxygen, high salinity, or poor circulation environments. Stainless steel is used where both the properties of steel and resistance to corrosion are required. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. The screws' countersunk heads are designed to sink flush with substrates to leave a smooth surface finish. They have single threads, designed to offer higher pull out values and quicker insertion.Multi-Purpose Pozi Screw Countersunk ST Stainless Steel 4.0 x 25mm Box 200
This Forgefix Contractors Fixing Band is a medium-duty, flexible and strong band which is easy to cut and bend. The band has pre-punched holes for fixing bolts and screws, and is made from galvanised steel for protection against corrosion. Supplied in 10m rolls in a durable cassette. APPLICATION:Ideal for fixing, supporting joists and many more superficial installations.Can be used with screws and galvanised twist nails. Galvanisation is process of applying a protective zinc coating to steel in order to prevent rusting. Zinc coatings prevent corrosion of the protected metal by forming a physical barrier, and by acting as a sacrificial anode even if this barrier is damaged.Contractors Galvanised Fixing Band Medium Duty 17mm x 0,7 x 10m Box 1
The Forgefix Rimless Wall Plugs can be inserted to depths below the surface of the base material. Their sprung anti-spin fins provide a two-way lock, preventing spinning and loosening from overhead applications. Due to this precise two-way expansion, the plugs are suitable for close to edge applications. Made from 100% Nylon. APPLICATION:Ideal for both lightweight and medium-duty fixing applications.Ideal for fixing wall lights, shelving and cupboards.Often used for satellite dish installation.Suitable for most types of threaded screws including multi-purpose, general purpose, coach screws etc. Not suitable for Machine Screw threads.Nylon Wall Plug Rimless M6 x 30 Bag 100
These Forgefix High Tensile Hex Head Bolts are made from 8.8 grade steel. The bolts are part threaded and conform to DIN 933 standards. The hexagonal head has been designed for use with spanners or sockets and offers maximum torque when used with these tools. APPLICATION:For fastening together numerous types of material or to be fastened into pre-tapped holes. Widely used in many engineering applications. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrityHigh Tensile Bolts ZP M10 x 140 Bag 10
These Forgefix Phillips, twin fine thread Drywall Screws have a zinc plated finish for increased durability. The screws come complete with a Phillips No.2 insert bit. Their Bugle Head allows the screw to sink effortlessly into the dry lining eithout the need for countersinking, which in turn minimises the damage to the surface. APPLICATION:Designed for fitting dry linings to studding. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminum and stainless steels by their oxide layers. The Phillips screw has four simple tapered slots. It is designed so that a Phillips tip screwdriver can turn a Phillips screw with increasing torque. When the torque gets to be too strong for the tip then the screwdriver tip winds itself out of the screw thus preventing over-tightening and or damage to the screw head. Fine thread screws have an extremely sharp point which not only pierces the plasterboard skin but will also allow the screw to drill through thin steel base structures.Drywall Screw Phillips Bugle Head TFT ZP 3.5 x 25mm Bulk 1000
The ForgeFix Dome Head Rivet has a steel-plated stem and Aluminium head which provides a neat appearance with a low profile. This rivet is the most versatile and commonly specified head style. The dome head has a diameter double that of the rivet body providing more than sufficient bearing surface to retain all but the extremely soft or brittle materials.The rivet assembly is inserted into a hole drilled through the parts to be joined together and can be finally fixed by use of a hand held or pneumatic rivet gun.
These Forgefix Pozi Carcass Screws have an extremely coarse single thread. The have a black phosphate coating for increased durability and a self drill point for easy installation. APPLICATION:Designed specifically for chipboard and MDF (medium density fibre) board and carcass assembly. Phosphate coatings are made up of thin crystalline layers of phosphate compounds that adhere to the surface of the fixing or fastener. The phosphate crystals are porous and can be formed from zinc, manganese, or iron phosphate solutions. Phosphate coatings offer good corrosion resistance and have an excellent ability to absorb supplementary coatings which improves appearance, corrosion resistance and resistance to abrasion. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. Coarse thread screws have an extremely sharp point and are designed to penetrate plasterboard skin. The coarse thread eases in to the board then the timber baton holding the board firm.Carcass Screw Pozi SCT Black Phosphate 4.2 x 32mm Box 200
These Forgefix Threaded Rods are made of A2 stainless steel, which will not corrode, rust or stain from water. This makes them ideally suited for corrosive and coastal applications as well as many other varied applications. They can be used with many other products including Drop in Anchors and Masonry Anchor Shields, and provide a cost effective fastening for many applications. Conform to DIN 975 standards. APPLICATION:Used widely in the soft furnishing trades where strong timber connection is required. Also extensively used in Playground and Climbing Wall manufacturing.Ideal for use in chemical fixing applications where non standard sizes are required. A2 Type 304 Stainless Steel can also be called 18/8 because it contains approximately 18% Chromium and 8% Nickel. It is austenitic steel and is non-magnetic. The chromium provides a corrosion and oxidation resistance, although it may tarnish. It is immune to foodstuffs, sterilising solutions, most organic chemicals and dyestuffs and also a wide variety of inorganic chemicals. As such, it is used extensively for many types of fixings and fasteners used in sanitary or hygiene applications.Threaded Rod Stainless Steel M12 x 1m Box 1
These Forgefix Multi-Purpose Pozi Screws with countersunk heads have a zinc finish for increased durability. The screws are immensely popular and versatile, and used in all trades including joinery, electrical and plumbing. Also widely used in DIY applications. APPLICATIONSuitable for use with many materials including PVCu, Timber, Chipboard, MDF, and other similar types. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminium and stainless steels by their oxide layers. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. The countersunk head is designed to sink flush with substrates to leave a smooth surface finish. They have single threads, designed to offer higher pull out values and quicker insertion.Specifications: Size: 3.5 x 30mm.Box quantity: 200.
These Forgefix Pozidriv Machine Screws are designed for use with nuts or pre-tapped holes. They are Zinc plated for increased corrosion resistance. Their Pan Head with a flat under head surface makes the screws ideal to lay flat on sheet material of all types, thus reducing deformation. APPLICATION:Ideal for use in many DIY, ironmongery, electrical and plumbing applications. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminum and stainless steels by their oxide layers. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. A Machine screw is generally a smaller fastener, threaded the entire length of its shank that usually has a recessed drive type (Slotted, Phillips, etc.).Machine Screw Pozi Pan Head ZP M6 x 50 Bag 25
These Forgefix Wing Nuts are a convenient alternative to the standard Hex Nut, and allow hand tightening rather than having to use spanners or other tools. The nuts are bright zinc plated for increased corrosion resistance. Also known as a 'Thumbscrew', the wing nut has two large metal 'wings' for easy tightening and loosening. APPLICATION:Where ever a hand tightened fastening is required. Used where frequent adjustments are needed or part removal can be made quickly at some later stage.Can be used with all threaded bolt products. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminum and stainless steels by their oxide layers.Wing Nut ZP M5 Bag 10
Forgefix Hex Head Lightning Bolts provide a virtually stress-free fixing for close to edge applications. They are self-threading and allow quick and easy installation of most masonry fixing applications. They can simply be screwed into a pre-drilled hole, without the need for a sleeve or plug. The bolts are through-fixing, eliminating the need for marking and re-positioning. They have a high load capacity due to the thread interlocking into the base material. The bolts have an 'Elementech' coating for superior anti-corrosion, which has been salt spray tested to 1,000 hours. Applications: Widely used for fixing battens, balustrades, handrails, racking and holding down machinery, plus many more installation applications. Suitable for most masonry substrates including concrete and brickwork but also for hollow block or bricks due to the nature of the thread type anchoring along the total length of the fixing.Specifications: Size: M10 x 100mm.Pack quantity: 10.
Tacwise galvanised narrow crown staples, ideal for a wide variety of 2nd fix tasks. Suitable for 191EL Pro Stapler/Nailer, Tacwise 35 Duo Nailer/Stapler and Tacwise 50 Duo Nailer/Stapler and other major brands in the market.Size: 18mm.Pack quantity: 1000
Plasplugs® Solid Wall Super Grips™ are suitable for fixing into concrete and brick. They are available in 3 different sizes/colours. Yellow: Regular-duty, accepts screws No.4-8 (3-4.5mm)Red: Regular-duty, accepts screws No.6-12 (3.5-5.5mm)Brown: Heavy-duty, accepts screws No.8-14 (4.5-7mm)This assorted pack contains the following: 50 x Regular-duty yellow Super Grips™: Accepts screws No 4-8 (3-4.5mm).50 x Regular-duty red Super Grips™: Accepts screws No 6-12 (3.5-5.5mm).50 x Heavy-duty brown Super Grips™: Accepts screws No 8-14 (4.5-7mm).
The Everbuild brand is not only hugely popular with tradesmen and DIY'ers. It's quite literally huge - the biggest range in the business. In addition to core manufactured products the Everbuild range includes a wide range of ancillary items from sealant guns to dust sheets, line markers to masking tape. The range of products Everbuild actually manufacture is extensive, from chemical blending for admixtures and water proofers through water based sealant manufacturing to the highly advanced polymer engineering undertaken in manufacturing silicone and hybrid sealants, as well as adhesives and a wide range of powder products. Everbuild Stick 2 All Purpose Spray Contact Adhesive is a sprayable glue which bonds to most common materials including wood, concrete, stone, tiles, rubber, foam, metals, rigid plastics, polyethylene, canvas fabrics, cardboard, paper and cork. It is ideal for securing most carpets/floor coverings. Suitable for internal and external use, giving permanent or temporary adhesion. It provides good adhesion with a good rate of tack development, is easy to use with no messy spreading / clearing up and is halogen and CFC free. Size : 500 ml.
The Everbuild 502 series All Purpose Weatherproof Wood Adhesive is a high quality, resin based wood adhesive for all wood bonding. It can be used internally and externally and provides a high strength , impact resistant bond that is usually stronger than the wood itself. Ideal for all general woodworking and joinery uses, furniture assembly and household DIY use. Conforms to international standard EN 204 (D3) and BS 14256 for creep resistance.The Everbuild EVBWOODO250 is supplied in a 250ml bottle.
This Everbuild SURVEYRE comes in a varity of colours: Blue, Red, White and Yellow an are ideal for identifying walkways, product storage locations and fire exit routes or to create floor markings to indicate pallet locations and aisle identification on concrete floors. This high definition, fast drying, spot marking paint is ideal for most applications where spot markings are required. The semi permanent formula lasts at least 3 months after application. A spray applied marking paint for contractor's/surveyor's spot marking. Colour-coded for electric, gas, water and cable company use. Semi-permanent formula lasts at least 3 months after application.Colour: BlueSize: 700ml
Everbuild Pinkgrip SF direct bond solvent-free gap filling adhesive specifically formulated for the professional user. The product can be used to replace mechanical fixings in a wide variety of building and home improvement applications for bonding wood, brick, plaster, plasterboard, polystyrene, Styrofoam and most plastics, metals and numerous other surfaces and is designed primarily for internal use. Approximately 12 linear meters for a 6mm diameter bead.
The Everbuild Instant Nails is a high strength, solvent-free, gap filling multi use adhesive that provides a quick grab and replaces mechanical fixings in many home improvement applications. Dries white and may be overpainted if required. Instant Nails should be at room temperature when you begin using the product. If Instant Nails has been stored in cool conditions it should be placed in a warm room/bucket of warm water before use to gently heat up to working temperature. Do NOT apply Instant Nails at temperatures below +4°C.
Pink Grip is a revolutionary direct bond adhesive specifically formulated for the professional user, using polymers at the leading edge of adhesive technology. Pinkgrip will stick just about anything on a building site that needs sticking. Its amazing grabbing strength not only removes the need to pin under the work piece to prevent slumping, but its revolutionary initial Direct Bond eliminates the need for double stick methods. Pinkgrip can be used inside and outside and adheres to just about every building substrate, providing the following key benefits: - Enhanced slump resistance for quick and simple direct bonding to most substrates without the use of temporary supports in most applications. - Excellent early and ultimate adhesive strength on porous substrates. - Excellent gap filling properties to accommodate uneven surfaces. - Good nip off qualities to prevent messy stringing of the adhesive Size: 350ml cartridge.
Everbuild Black Jack® 908 D.P.M. is a ready-to-use, odourless, rubber enriched bitumen emulsion that provides a highly effective sandwich damp-proof membrane for floors. It also acts as a waterproofer for walls, above ground structures and foundations. It can also be used as an adhesive for wood block, mosaic panels, insulation boards, expanded polystyrene, cork and as a plaster bonding agent, even on difficult surfaces. Suitable for internal and external use.
The Everbuild Industrial Superglue is a medium viscosity formula that can fill gaps to 0.1mm. This Everbuild product is a very strong industrial superglue that is ideal for use on perfect fit surfaces where fast setting is required. It bonds non-porous surfaces like, plastics, metals, glass, PVCu, rubber and EPDM and has a viscosity at 25° c of 100cps and a setting time of 5 to 15 seconds so you will get the job in hand done quickly and with a professional finish.Size - 50 g.
Everbuild Evercryl is a resin based, fibre reinforced roof repair compound which is effective on all common roofing surfaces and types, giving an instant roof repair even in the wet and on wet surfaces. Evercryl may also be applied in frosty conditions down to -5°C. Evercryl One Coat is instantly waterproof when applied, so there is no fear of washoff. Emergency leaks can be tackled immediately as there is no need to wait for the rain to stop. Evercryl One Coat is brush applied and dries to a smooth seamless flexible membrane which resists algae and fungal growth. Because of the high level of fibre reinforcement, Evercryl One Coat will bridge small cracks and requires only a one coat brush application to give instant and total water protection, even in areas subject to ponding. Evercryl One Coat requires no primer on sound non-porous surfaces. BENEFITS- May be applied in damp and wet conditions.- Formulated from lightfast acrylic polymers to withstand sunlight for longer periods than traditional bitumen coatings.- Fibre reinforced to bridge small cracks.- Primerless adhesion to most bituminous and non-porous surfaces. AREAS FOR USE- General sealing, maintenance, repair and waterproofing of most common roofs in wet or dry conditions - for use on concrete, fibre/cement, roofing felt mastic asphalt, existing bituminous roof coatings, rigid PVCu corrugated iron, metals, slates, brickwork, tiles, lead, copper and zinc. - Waterproofing guttering (plastic and metal), downpipes, gully, flashings, upstands, vents and leadwork.1 x Everbuild Evercryl One CoatColour: GreySize: 5kg
