Forgefix TechFast Metal Roofing Panels to Timber Hex Screws are used to join metal roofing panels to timber frame buildings. They have a specially designed compression control thread to prevent damage and denting of panels. No pre-drilling is required and the self-drilling T17 Gash Point on screws makes for a rapid installation. The nails are fire and corrosion resistant, protected by Elementech corrosion resistant coating, salt spray tested to 1000 hours. Complies with EU Safety, Health and Environmental requirements. They are supplied with 16mm EPDM rubber washers.These Forgefix TechFast Metal Roofing to Timber Screws have the following specification: Size: 6.3 x 80mmSteel Thickness: 0.5-1.2mmHead Type: 8mm HexPack Size: 100
These Forgefix Socket Screws have a raised head, and are designed for attaching electrical wall sockets and switches. The screws have a slotted head and are nickel plated for increased durability. APPLICATIONUsed specifically for attaching electrical wall socket and switches to back plates. The Nickel plating process coats mild steel or stainless steel to considerably prolong the part’s life. Nickel plating is probably the most corrosion resistant finish available and is often used on socket screws for electric switch sockets avoiding corrosion and cross contamination. It leaves a bright aesthetic finish and is extremely hardwearing. With slotted screwdrivers it is important to ensure that the tip matches the width of the screw slot, otherwise you run the risk of damaging the screw head. Slotted screwdrivers are available with either Flared or Parallel tips. For the majority of uses the Flared tip is ideal but if the screw needs to be driven below the material surface a Parallel tip screwdriver should be used. Raised heads have both countersunk and raised structure which is designed for aesthetic purposes on all types of ironmongery and lighting applications.Socket Screw Slotted Raised Head Nickle Plated 3.5 x 75mm Bag 100
SMJ Traditional profile single or double light switch made from white plastic. Suitable for interior use. Available in 1, 2 or 3 Gang, with 1 or 2-Way options. Fixings supplied.This SMJ 1 Gang Light Switch is ideal for controlling 1 circuit. 2 way switch, make it possible to control the same light from 2 locations. Supplied in a Trade Pack.
These Faithfull welded steel chains are made with the link side welded for extra strength. They have mild steel welded straight links made to form an A style short link chain. The chains are bright zinc plated and ideal for general purpose applications such as securing loads. Maximum load figures quoted are for guidance only. These chains are test load tested, but not certified and should never be used for any overhead lifting, load binding or towing applications.The Faithfull FAICHCUT25Z Zinc Plated Chain has the following specifications:Size: 2.5mm x 2.5mFinish: Zinc
These Faithfull welded steel chains are made with the link side welded for extra strength. They have mild steel welded straight links made to form an A style short link chain. The chains are bright zinc plated and ideal for general purpose applications such as securing loads. Maximum load figures quoted are for guidance only. These chains are test load tested, but not certified and should never be used for any overhead lifting, load binding or towing applications.The Faithfull FAICHAL615 A link chain has the following dimensions:Thickness: 6mmLength: 15m
These Faithfull Welded Chains are manufactured from a mild steel with a Black Japanned finish. These chains are load tested, but not certified and should never be used for any overhead lifting, load binding or towing applications. Maximum load figures quoted are for guidance ONLY.This Faithfull Black Japanned Chain has the following specifications: Link Diameter: 4mmChain Length: 30m.Max Load: 120kg.
The Faithfull Plastic Chain is available in a selection of colours, this range of polythene plastic chain is ideal for both internal and external use. Its alternately contrasting colour sections make it particularly useful when specific areas need to be clearly sectioned off. These plastic chains are supplied in 12.5m reels.The Faithfull FAICHPYB812C plastic chain is yellow and black with the following dimensions: Thickness: 8mm
The Faithfull versatile clock chain has many applications including the hanging of lightweight pictures and lamps. It is also commonly used by keen model makers and enthusiastic hobbyists. These chains have unwelded split links so that it can be altered to achieve the desired length. Available in brass, chrome or stainless steel.This Faithfull Clock Chain is made from stainless steel, with the following specifications: Link Diameter: 2mm.Link Length: 19mm.Length: 10m.
These Forgefix Spring Head Nails are a popular roofing nail for corrugated roofing. Their twisted shank assists in absorbing movement that may occur in the roofing construction. They are galvanised for increased resistance to corrosion. APPLICATION:Galvanised spring head nails are most commonly used for securing corrugated sheeting and other roofing materials.Can be used with a rubber or plastic spat washer. Galvanisation is process of applying a protective zinc coating to steel in order to prevent rusting. Zinc coatings prevent corrosion of the protected metal by forming a physical barrier, and by acting as a sacrificial anode even if this barrier is damaged.
These Forgefix High Tensile Hex Head Bolts are made from 8.8 grade steel. The bolts are part threaded and conform to DIN 933 standards. The hexagonal head has been designed for use with spanners or sockets and offers maximum torque when used with these tools. APPLICATION:For fastening together numerous types of material or to be fastened into pre-tapped holes. Widely used in many engineering applications. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrityHigh Tensile Bolts ZP M6 x 50 Bag 10
These Forgefix Phillips, Single Coarse Thread (SCT) Drywall Screws have a black phosphate finish for increased durability. Their Bugle Head allows the screw to sink effortlessly into the dry lining without the need for countersinking, which in turn minimises the damage to the surface. They are supplied collated, with 50 screws per strip and 1,000 screws per box. APPLICATION:Designed for fitting dry lining to studding. Phosphate coatings are made up of thin crystalline layers of phosphate compounds that adhere to the surface of the fixing or fastener. The phosphate crystals are porous and can be formed from zinc, manganese, or iron phosphate solutions. Phosphate coatings offer good corrosion resistance and have an excellent ability to absorb supplementary coatings which improves appearance, corrosion resistance and resistance to abrasion. The Phillips screw has four simple tapered slots. It is designed so that a Phillips tip screwdriver can turn a screw with increasing torque. When the torque gets to be too strong for the tip then the screwdriver tip winds itself out of the screw thus preventing over-tightening and or damage to the screw head. Coarse thread screws (mainly drywall screws) have an extremely sharp point and are designed to penetrate plasterboard skin. The coarse thread eases in to the board then the timber baton holding the board firm.Drywall Collated Screw Phillips Bugle Head SCT 3.9 x 38mm Box 1000
These Forgefix High Tensile Hex Head Bolts are made from 8.8 grade steel. The bolts are part threaded and conform to DIN 933 standards. The hexagonal head has been designed for use with spanners or sockets and offers maximum torque when used with these tools. APPLICATION:For fastening together numerous types of material or to be fastened into pre-tapped holes. Widely used in many engineering applications. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrityHigh Tensile Bolts ZP M10 x 50 Bag 10
These ForgeFix Don Quichotte Light Gauge Masonry Nails have the following specification: Size: 2.5 x 25mmFinish: Zinc GalvanisedPack Quantity: Box of 100
ForgeFix ForgeFast Wood Screws have a universally accepted, Torx® compatible drive. Their recessed ribs provide improved countersinking and reduced surface dust, and their reinforced countersunk necks improve holding power. The screws have a patented drill and drive thread for reduced splitting of the timber, reduced 'jacking' and spinning of joined timber, increased pull-out and a firmer fix. A sharp point provides faster bite and is capable of piercing 0.8mm steel. The screws have an 'Elementech 400' coating providing an anti-corrosive metal finish, which lasts up to 6 times longer than standard zinc coatings. The coating is environmentally friendly and does not contain Cr6+. It is Salt Spray tested to 400 hours. The screws are suitable for interior use. Every tub is supplied with a Torx® compatible bit.Size: 5.0 x 60mm.Pack quantity: 500.
Box of 50 MasonMate Metal Frame Anchors 10 x 112mm. The MasonMate All Steel Metal Frame Anchors produced for fixing door and window frames to most building materials. All steel for strength and durability. 10 x 112mm (50)
Forgefix TechFast Timber to Steel CSK/Wing Screws are used to join timber to steel frame buildings. The screws are fitted with breakaway wings that create a clearance hole to protect thread from engaging timber when drilling through. Breakaway wings will ream a hole, then break-off when they contact the metal surface to be drilled. The thread will then engage with metal. They have a TORX® compatible insert for a higher transmission of power. With improved countersinking from recessed ribs. Fire and corrosion resistant. Complies with EU Safety, Health and Environmental requirements.These Forgefix TechFast Timber to Steel CSK/Wing Screws have the following specification: Size: 5.5 x 65mmClamping Thickness: 45mmEffective Thread Length: 44mmPack Size: 100Drill Tip: No.3 No.3 drill tip for self-drilling heavy gauge steel up to 5mm.
These Forgefix Phillips, Single Coarse Thread (SCT) Drywall Screws have a black phosphate finish for increased durability. Their Bugle Head allows the screw to sink effortlessly into the dry lining without the need for countersinking, which in turn minimises the damage to the surface. They are supplied collated, with 50 screws per strip and 1,000 screws per box. APPLICATION:Designed for fitting dry lining to studding. Phosphate coatings are made up of thin crystalline layers of phosphate compounds that adhere to the surface of the fixing or fastener. The phosphate crystals are porous and can be formed from zinc, manganese, or iron phosphate solutions. Phosphate coatings offer good corrosion resistance and have an excellent ability to absorb supplementary coatings which improves appearance, corrosion resistance and resistance to abrasion. The Phillips screw has four simple tapered slots. It is designed so that a Phillips tip screwdriver can turn a screw with increasing torque. When the torque gets to be too strong for the tip then the screwdriver tip winds itself out of the screw thus preventing over-tightening and or damage to the screw head. Coarse thread screws (mainly drywall screws) have an extremely sharp point and are designed to penetrate plasterboard skin. The coarse thread eases in to the board then the timber baton holding the board firm.Drywall Collated Screw Phillips Bugle Head SCT 3.9 x 55mm Box 1000
