Faithfull Long series pin punch with extended parallel shank, used for the removal of tight pin and metal dowels from mechanical fittings and machinery. Designed for heavy-duty use and made from uniformly heat treated tool steel with a round head and a knurled body for a firm grip. Set of 8 includes: 1.6, 2.4, 3.2, 4, 4.8, 6, 8 and 10mm. Pin length: 90mm (3.1/2in).Overall length: 200mm (8in).Size: 4.8mm (3/16in)
Faithfull Centre punch with a square head which provides a larger striking area and prevents the punch rolling when laid on the bench. Carefully hardened and tempered and with a 90° ground point.Point Diameter: 6mm (1/4in).Length: 100mm (4in).
The Moore & Wright CSM Precision Rules are fully hardened and tempered precision rules with deeply etched graduations on both sides for ease of reading and long life. Theseare rules specifically designed for use with the Combination Sets (MAWCSM300 & MAWCSME12).The Moore & Wright CSRM600 is a 600mm rule is perfect for use with the combination sets and is graduated on both sides. Measurements: mm and 0.5mm on both sides; numbered every 10mm. PLEASE NOTE This is ONLY the Rule.
The Facom 249.G sheathed drift punches are tough and durable. With very high tensile strength, these punches feature a head hardened to 43 HRc and a long shank hardened to 58 HRc. The handles are ergonomically shaped for comfort and shock absorption. Ideal as an aid in aligning bolt or rivet holes prior to inserting a fastener.The FCM249G12 Sheathed Punch has the following specifications:Point diameter: 11.80mm.Length: 280mm.
Recoil inserts are the quick and easy way to repair damaged threads or create stronger original threads in alloys and composite materials in original equipment manufacture.Made from corrosion resistant stainless steel, they create stronger threads in most materials and simplify changeover from unified to metric or vice versa. Recoil thread repair kits contain a quality HSS tap, installation tool, precision stainless steel inserts and instructions. Supplied in a sturdy container.Please note NOT supplied with a tapping drill.Kit 20mm x 2.5Length 1 1/2D
Metric 333mm lengths of high carbon bright steel, precision ground to very close tolerances; Above 25mm + - 0.025mm.Below 25mm + - 0.0127mm. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 6mm
Wad punches are used for cutting holes in soft materials or for producing discs from the material being cut.One piece forging with ground and polished tapered section.Size 14mm (9/16 in)
This hollow punch is made from carbon steel. It has a ground tapered section with a milled clearway for removing waste materials. It is intended for cutting soft materials such as leather.
A hardened and tempered parallel pin punch, which is used for removing pins in parallel holes. The pin should be first started with a hand or taper punch to avoid damage to the point of the parallel punch.Size 5.5mm (7/32 in).
The Moore & Wright DPC Series Digital Caliper has a Polycarbonate frame and offers 4 way measurement (mm/inch, absolute/incremental measurement) with an accuracy of ± 0.2mm/0.008in. The caliper can be zeroed at any point on the scale. Supplied with a CR2032 battery and a vinyl pouch. Specification Range: 0-150mm (0-6in).Resolution: 0.01mm (0.005in).Jaws: 40mm.
The Faithfull Spring Dividers have polished natural steel finish legs made of flat stock. They are carefully balanced, with heat treated points. A strong but flexible bow spring and centrally located adjustment screw give a smooth and precise action.Size 100mm (4 in)
The Moore & Wright Spring Dividers are manufactured from polished tool steel and the points are hardened to over 550Hv. The bow spring ensures uniform tension over working range and they are fitted with a centrally mounted adjustment screw. These Spring Dividers comply with BS3123 standards. Note: The nominal size is the distance between the centre of the roller and the working ends of the legs.The Moore & Wright 506 Spring Dividers have the following specifications: Size: 150mm (6in).
The Moore & Wright 110-DBL Series Digital Calipers display values in mm/inch and feature ABS / INC measurement settings. All the metal parts are made from hardened stainless steel. The calipers offer a zero point at any position and a conveniently located on/off button. The calipers are manufactured to DIN 862 standards. Supplied with a CR2032 battery.The MAW11015DBL calipers have the following specifications: Range: 0-150mm (0-6in).Resolution: 0.01mm (0.005in).Jaws: 40mm. Supplied retail packed and in a plastic pouch.
A comfortable DynaGrip sleeve surrounds a fully hardened body, which is precision milled for extra long life. The overall length is 25% longer than conventional nail punches, making it easy to set nails in hidden and hard to reach areas. Colour coded sleeves for easier identification of sizes.Tip Size: 1/16inLength: 5inColour: Grey Sleeve
A comfortable DynaGrip sleeve surrounds a fully hardened body, which is precision milled for extra long life. The overall length is 25% longer than conventional nail punches, making it easy to set nails in hidden and hard to reach areas. Colour coded sleeves for easier identification of sizes.Tip Size: 2.4mmLength: 5inColour: Red Sleeve
A quick and easy way to cut clean imperial sized holes in sheet metal up to 16 gauge. The special design allows an even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches boxed singly without key, which should be ordered separately. To use these punches they require a hole to be drilled through the sheet metal (large enough to clear the heagonal Screw) then the Die and hexagonal screw are threaded through the sheet metal then onto the die nut and screw die nut. When the hexagonal screw is tightened the punch will cut cleanly and evenly through the metal.Size. 3/8 in.Key Type 3/16 in hexagon wrench
Dormer E500 straight flute taps are the only type of taps that can be used by hand, but they may also be used in a machine if required. Extremely versatile, can tap through or blind holes in most materials. When tapping blind holes straight flute taps should be used in sets. The three taps which form a set are known by more than one name. 1. Taper or First tap2. Second or Intermediate tap3. Bottoming, third or plug tap. Metric coarse straight flute taps. Tolerance: Class 2 for 6H FitSurface treatment: BrightMaterial: HSS High Speed SteelChamfer No: 1,2 and 3, Serial no 4 and 5Flute Geometry: Straight Flutes ISO529Size 12.0mm x 1.75 set of 3
The Moore & Wright Water Resistant Series Digital Caliper are fitted with a patented ceramic capacitive sensor and a large LCD display that offers 4 way measurement (mm/inch, absolute/incremental measurement). They can be zeroed at any point on the scale and is fitted with a conveniently located on/off switch. The calipers are manufactured to DIN 862 standards and water and dust resistant to IP54 specifications. Supplied with a CR2032 battery. Specification Range: 0-150mm (0-6in).Resolution: 0.01mm (0.005in).Jaws: 40mm.
The Moore & Wright 56R Spring Joint Jenny Caliper is manufactured from polished tool steel and the marking leg has been hardened to over 550Hv at the point. It is fitted with a bow spring that ensures uniform tension over the working range and a centrally mounted adjustment screw that offers finer setting than firm joint type. Also known as Hermaphrodite calipers. Size: 150mm (6in).
The BlueSpot Tools Drill & Tap Set is manufactured from hardened steel for increased hardness and a clean thread. Includes a range of common tap sizes and the drill bit required for that size of thread. Suitable for use with plastics (use distilled water as coolant), steel, aluminium and other non-ferrous metals. Supplied in a metal tin for easy access and storage. Contains: 7 x Drills: 2.5, 3.3, 4.2, 5, 6.8, 8.5, 10.2mm7 x Taps: M3, M4, M5, M6, M8, M10, M121 x Tap Wrench
SB-3732 series nail punches are manufactured with a plastic handle and fully polished steel surface with a brilliant chrome finish.Tip size: 4.0 mm (5/32in). Length: 125 mm (5in).
SB-3732 series nail punches are manufactured with a plastic handle and fully polished steel surface with a brilliant chrome finish.Tip size: 2.0 mm (5/64in). Length: 125 mm (5in).
The Moore & Wright MW279-01A Micrometer Stand is designed for micrometers up to 100mm (4in). It has a painted cast iron base with plastic covered clamping jaws and the angle of the jaws can be adjusted.
