Widely used in automotive, aviation, diesel and farm equipment manufacture and also in jig, fixture and gauge work. Packed individually in envelope. Metric gauge 300 mm long.Thickness: 0.10mm
Feeler strips are widely used in automotive, aviation, diesel and farm equipment manufacture and service. Also used in jig, fixture and gauge work. Packed individually in an envelope. Length: 300mm (12in).Inch Gauge 12 in long Thickness: 0.010 in
A quick and easy way to cut clean metric sized holes in sheet metal up to 16 gauge. The special design allows even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches are sold singly without key, which should be ordered separately. Thread the punch onto the hexagonal screw and then pass the hexagonal screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting hexagonal screw until it touches the metal sheet. Use a hexagonal key to turn the hexagonal screw. The screw will pull the punch through the metal and a hole will result. Please note these instructions apply to cutters up to 15 mm in size, for cutters 15 mm and over have a different configuration. Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.Size.32.5mm.Key Type.MC. 10mm hexagonal wrench
Extra long pin punch. Hardened and tempered with a knurled grip. The drive pin sections are 90mm (3.1/2in) long and the diameters of the punches are slightly under the sizes listed. Length: 200mm (8in).1 x Starrett S248PC Long Pin Punch Set 5 Piece Sizes: 3mm (1/8in), 5mm (3/16in), 6mm (1/4in), 8mm (5/16in) and 9.5mm (3/8in).
Imperial 13in lengths of high carbon bright steel, precision ground to very close tolerances; Above 1 in + - 0.0005in.Below 1 in + - 0.00025in. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 5/16 in
Dormer E500 straight flute taps are the only type of taps that can be used by hand, but they may also be used in a machine if required. Extremely versatile, can tap through or blind holes in most materials. When tapping blind holes straight flute taps should be used in sets. The three taps which form a set are known by more than one name. 1. Taper or First tap2. Second or Intermediate tap3. Bottoming, third or plug tap. Metric coarse straight flute taps. Tolerance: Class 2 for 6H FitSurface treatment: BrightMaterial: HSS High Speed SteelChamfer No: 1,2 and 3, Serial no 4 and 5Flute Geometry: Straight Flutes ISO529Size 10.0mm x 1.5 second
The RIDGID Inner-Outer Reamers have a hardened steel construction and are suitable for cutting copper and stainless steel tubing. They have 46 cutting edges on the interior cone that allow for fast, clean, inner reaming and outer deburring/bevelling of 1⁄4in (6mm) to 2in (50mm). The reamers have dual inch/metric measurement bars.RIDGID 223S EN Inner-Outer Reamer Capacity: 6 - 40mm (1/4 - 1.1/4in).Weight: 0.34kg.
Metric 333mm lengths of high carbon bright steel, precision ground to very close tolerances; Above 25mm + - 0.025mm.Below 25mm + - 0.0127mm. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 13mm
The Faithfull Digital Calipers are made from hardened stainless steel, this electronic digital caliper provides precision readings through a clear liquid crystal display. Its many features include a fine adjustment roller which allows precise measurements to be taken quickly and easily. The digital section button enables readings to be displayed in either metric or imperial format. The four-way measurement function provides a choice of readings in external, internal, depth and step modes. The strong plastic storage case enables the caliper to be kept in a dust and damp free environment. Specifications: Measuring range: 0-150mm / 0-6inResolution: 0.01mm / 0.0005inAccuracy: ±0.03mm / 0.001inRepeatability: 0.01mm / 0.0005inMax measuring speed: 1.5m/sec, 60in/secMeasuring system: Linear capacitive measuring systemDisplay: LCD displayCharacter Height: 6.35mmWorking temperature: 5-40°C, 41-104°FData output: Serial output for interface with computer or printerBattery: 1.55V, LR44Auto power off: 5 minutes
Faithfull Letter punches are used for hand marking metals and other hard materials. They are useful for stamping personal identification or post codes on tools, cycles etc., as frequently recommended by police and insurers. The letter sizes as shown, relate to the height of the characters. The punches are manufactured from high quality tested carbon steel with double induction hardened heads to ensure high quality impressions. The body is hardened and the head is tempered to prevent chipping when hammered. Each set contains twenty seven punches with the characters & and A to Z.Set supplied in plastic box.Size : 4mm (5/32 in).
The Faithfull Automatic Centre Punch is ideal for making light indents to heavy punching without using a hammer. Pressure can be varied from 5lbs to approximately 30lbs simply by rotating the head. Tip diameter: 4mm (5/32in).Length: 100mm (4in).
Type 117 Centre punches are manufactured from specially selected steel, hardened and properly tempered. They are well proportioned, nicely finished and have a knurled finger grip. The points are ground at the proper angle to give maximum service, and the tips are accurately centered. Length: 100mm (4in).Size 2.5 x 100mm(3/32 x 4 in)
A comfortable DynaGrip sleeve surrounds a fully hardened body, which is precision milled for extra long life. The overall length is 25% longer than conventional nail punches, making it easy to set nails in hidden and hard to reach areas. Colour coded sleeves for easier identification of sizes.This set of 3 punches contains the following tip sizes:1/32in (0.8mm) Yellow Sleeve 1/16in (1.6mm) Grey Sleeve3/32in (2.4mm) Red SleeveOverall Length: 125 mm / 5in
Hexagonal bodied parallel pin punches with extra long pins. Used for driving out long retaining pins. The pin should be first started with a hand or taper punch to avoid damage to the point of the pin punch. Pin length: 63mm (2.1/2in).Overall length: 152mm (6in).Size. 3.2mm (1/8 in).
Imperial 13in lengths of high carbon bright steel, precision ground to very close tolerances; Above 1 in + - 0.0005in.Below 1 in + - 0.00025in. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 1/8 in
The Faithfull Depth Gauge is a versatile tool that allows the angle and depth to be measured simultaneously. The protractor features deep etched graduations 0 - 180° in opposite directions permitting the reading of both the direct and supplementary angles. The rule is graduated in both imperial and metric dimensions up to 150mm (6in) and a knurled thumb nut allows the rule to be locked at the chosen angle. Blade Length: 150mm (6in).Graduations: 0.5mm or 64ths.
Feeler strips are widely used in automotive, aviation, diesel and farm equipment manufacture and service. Also used in jig, fixture and gauge work. Packed individually in an envelope. Length: 300mm (12in).Inch Gauge 12 in long Thickness: 0.002 in
The Faithfull FAITRAMMEL Trammel head set is supplied with information label and barcode. They feature needle point legs and have a bar capacity of 31mm. This device is used for drawing circles and measuring distances with the accuracy of a divider. Note: One trammel can also hold a pencil.
Metric 333mm lengths of high carbon bright steel, precision ground to very close tolerances; Above 25mm + - 0.025mm.Below 25mm + - 0.0127mm. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 11mm
Industrial quality bar type tap wrench manufactured from a high-quality steel. The wrench body is black powder-coated and houses two steel jaws. The handle is knurled for positive grip and control.Tap size capacity: M4 - M8
Faithfull Nail punch with a square head which provides a larger striking area and stops the punch rolling off the bench. Accurately hardened and tempered with a precision formed concave tip for better nail contact. Designed to drive nail heads below the surface of the wood.Point Diameter: 3mm (1/8in)Length: 100mm (4in)
The Faithfull Prestige Centre Finder Gauge is manufactured from aluminium using computer numerical controlled (CNC) machines. The black anodised finish offers enhanced corrosion protection and the laser engraved scales give outstanding measurement accuracy. The centre finder is used to find the centre point of a square or cylindrical object. It features ruled markings in millimetre increments and can also be used for 45° and 90° mitre cut lines, making this product ideal for any engineer's workshop.With a measuring capacity of 140mm, this tool can be used on objects with a diameter or width of up to 240mm. Specification: Length: 150mmMeasuring Capacity: 140mm
A hardened and tempered parallel pin punch, which is used for removing pins in parallel holes. The pin should be first started with a hand or taper punch to avoid damage to the point of the parallel punch.Size 3.2mm (1/8 in).
The Faithfull HSS Straight Flute Taps are versatile, general-purpose taps for threading blind or through-holes in most materials. Suitable for machine cutting, each set contains taper, second and bottom taps to accommodate all threading. The taps are made from high-speed steel, with a bright finish and conform to ISO529.Size: M8Thread: 1.25Drill Size: 6.9mm
Metric 333mm lengths of high carbon bright steel, precision ground to very close tolerances; Above 25mm + - 0.025mm.Below 25mm + - 0.0127mm. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 4mm
SB-3732 series nail punches are manufactured with a plastic handle and fully polished steel surface with a brilliant chrome finish.Tip size: 3.2 mm (1/8in).Length: 125 mm (5in).
The BlueSpot Screw Extraction Bits are manufactured from carbon steel and feature a reverse thread. They are used to remove broken/damaged screws and bolts. Simply insert into pre-drilled hole within screw and operate drill in reverse to remove screw without damage to hole. The square end also allows use with a tap wrench. Suitable for screws 3-25mm diameter.
Industrial quality bar type tap wrench manufactured from a high-quality steel. The wrench body is black powder-coated and houses two steel jaws. The handle is knurled for positive grip and control.Tap size capacity: M7 - M27
The Moore & Wright 110-DBL Series Digital Calipers display values in mm/inch and feature ABS / INC measurement settings. All the metal parts are made from hardened stainless steel. The calipers offer a zero point at any position and a conveniently located on/off button. The calipers are manufactured to DIN 862 standards. Supplied with a CR2032 battery.The MAW11020DBL calipers have the following specifications: Range: 0-200mm (0-8in).Resolution: 0.01mm (0.005in).Jaws: 50mm.
The Faithfull handy pocket sized multi purpose angle protractor manufactured from stainless steel. It can be used as a 100mm measuring rule but also functions as a protractor, a square, a centre finder, a circle divider and a drill point gauge.
The Faithfull HSS Straight Flute Split Dies are versatile, general-purpose dies for threading rods. They are suitable for most materials and can be used for hand or machine cutting. Each die threads a male thread to its equal and opposite female thread. All dies should be used with the corresponding rod size to ensure both cutting ease and thread efficiency. These dies are made from high-speed steel with a bright finish and conform to ISO529.Size: M5Thread: 0.8
Letter punches are for marking metals and other solid materials. Produced from quality steel, heat treated to give maximum endurance and accuracy of impression. Packed in attractive plastic box.Size. 3mm (1/8 in)Contents: A to Z plus & (and)
This hollow punch is made from carbon steel. It has a ground tapered section with a milled clearway for removing waste materials. It is intended for cutting soft materials such as leather.
Metric 333mm lengths of high carbon bright steel, precision ground to very close tolerances; Above 25mm + - 0.025mm.Below 25mm + - 0.0127mm. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 6mm
The Priory 124 Series Round Head Centre Punches are high quality, British manufactured punches.They are made from high quality carbon steel and heat-treated to exact tolerances. Precisely knurled body for firm grip.Specifications:Tip: 9.5mm (3/8in).Length: 150mm (6in).
