A quick and easy way to cut clean imperial sized holes in sheet metal up to 16 gauge. The special design allows an even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches boxed singly without key, which should be ordered separately. To use these punches they require a hole to be drilled through the sheet metal (large enough to clear the heagonal Screw) then the Die and hexagonal screw are threaded through the sheet metal then onto the die nut and screw die nut. When the hexagonal screw is tightened the punch will cut cleanly and evenly through the metal.Size. 1 1/4 in.Key Type.B. 5/16 in hexagonal wrench
Imperial 13in lengths of high carbon bright steel, precision ground to very close tolerances; Above 1 in + - 0.0005in.Below 1 in + - 0.00025in. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 5/32 in
Pin vices are chiefly used for holding small taps, reamers, scribers or wire. The handles are tubular which permit holding wires of any length or diameter up through the length of the tool.Size: 3Capacity: 1.5 - 3mm (1/16 - 1/8 in)
Pin vices are chiefly used for holding small taps, reamers, scribers or wire. The handles are tubular which permit holding wires of any length or diameter up through the length of the tool.Size: 2Capacity: 0.75 - 1.5mm (1/32 - 1/16)
Feeler strips are widely used in automotive, aviation, diesel and farm equipment manufacture and service. Also used in jig, fixture and gauge work. Packed individually in an envelope. Length: 300mm (12in).Inch Gauge 12 in long Thickness: 0.004 in
Widely used in automotive, aviation, diesel and farm equipment manufacture and also in jig, fixture and gauge work. Packed individually in envelope. Metric gauge 300 mm long.Thickness: 0.05mm
A quick and easy way to cut clean imperial sized holes in sheet metal up to 16 gauge. The special design allows an even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches boxed singly without key, which should be ordered separately. To use these punches they require a hole to be drilled through the sheet metal (large enough to clear the heagonal Screw) then the Die and hexagonal screw are threaded through the sheet metal then onto the die nut and screw die nut. When the hexagonal screw is tightened the punch will cut cleanly and evenly through the metal.Size. 1/2 in.Key Type 7/32 in hexagonal wrench
Recoil inserts are the quick and easy way to repair damaged threads or create stronger original threads in alloys and composite materials in original equipment manufacture.Made from corrosion resistant stainless steel, they create stronger threads in most materials and simplify changeover from unified to metric or vice versa. Recoil thread repair kits contain a quality HSS tap, installation tool, precision stainless steel inserts and instructions. Supplied in a sturdy container.Please note NOT supplied with a tapping drill.Kit 18.0mm x 2.5Length 1 1/2 x Diameter
The Faithfull Internal Spring Calipers, have polished, natural steel finish legs, are made of flat stock and are carefully balanced, with treated points. A strong but flexible bow spring and centrally located adjustment screw give a smooth and precise action.Size 100mm (4 in)
The Faithfull External Spring Calipers have polished, natural steel finish legs, are made of flat stock and are carefully balanced, with treated points. A strong but flexible bow spring and centrally located adjustment screw give a smooth and precise action.Size 100mm (4 in)
The Faithfull Internal Spring Calipers, have polished, natural steel finish legs, are made of flat stock and are carefully balanced, with treated points. A strong but flexible bow spring and centrally located adjustment screw give a smooth and precise action.Size 75mm (3 in)
The Faithfull HSS Straight Flute Taps are versatile, general-purpose taps for threading blind or through-holes in most materials. Suitable for machine cutting, each set contains taper, second and bottom taps to accommodate all threading. The taps are made from high-speed steel, with a bright finish and conform to ISO529.Size: M3Thread: 0.5Drill Size: 2.5mm
Dormer Dienuts are used to reclaim worn or damaged threads in most materials. Metric Coarse Dienuts. Application: For reclamation of screw threads. Also available in MF, UNC, G(BSPF) thread forms. Tolerance: 6g.Chamfer Lead: Two Threads.Surface treatment: Bright.Material: HSS - High Speed Steel. BS1127:1950Size: 8mm x 1.25.
The Faithfull Adjustable Magnetic Welding Clamp, also known as an 'adjustable links magnet', is a type of welding clamp where each magnet can be completely rotated. The 2 magnets can be adjusted to hold ferrous metal workpieces at any angle by tightening/loosening the wing nuts. The compact size allows it to be used in confined spaces. Ideal for use by welders and fabricators. Magnetic Block Size: 50 x 25mmOverall Size: 114 x 25 x 50mm
The Faithfull Prestige Angle Gauge is manufactured from aluminium using computer numerical controlled (CNC) machines. The black anodised finish offers enhanced corrosion protection and the laser engraved scales give outstanding measurement accuracy. The protractor features laser etched graduations from 0-180°. It is used to determine existing angles, as well as creating new angles, setting bevels and transferring angles from one surface to another. A knurled thumb-nut allows the rule to be locked at a chosen angle.
Recoil inserts are the quick and easy way to repair damaged threads or create stronger original threads in alloys and composite materials in original equipment manufacture.Made from corrosion resistant stainless steel, they create stronger threads in most materials and simplify changeover from unified to metric or vice versa. Recoil thread repair kits contain a quality HSS tap, installation tool, precision stainless steel inserts and instructions. Supplied in a sturdy container.Supplied with a tapping drill.Kit 7.0mm x 1.0Length 1 1/2 x Diameter
Recoil inserts are the quick and easy way to repair damaged threads or creating stronger original threads in alloys and composite materials in original equipment manufacture.Made from corrosion resistant stainless steel, they create stronger threads in most materials and simplifiy changeover from unified to metric or vice versa.They reduce thread wear and are interchangeable with other brands of inserts or tooling.Size. 14mm x 1.25 Length. 19mm (3/4 in).
Recoil inserts are the quick and easy way to repair damaged threads or creating stronger original threads in alloys and composite materials in original equipment manufacture.Made from corrosion resistant stainless steel, they create stronger threads in most materials and simplify changeover from unified to metric or vice versa. Recoil thread repair kits contain a quality HSS tap, Installation tool, precision stainless steel inserts and instructions.Supplied in a sturdy container.Supplied with a tapping drill.Kit 1/4 Whit x 20 tpiLength 1 1/2 x Diameter
Dormer Dienuts are used to reclaim worn or damaged threads in most materials. Metric Coarse Dienuts. Application: For reclamation of screw threads. Also available in MF, UNC, G(BSPF) thread forms. Tolerance: 6g.Chamfer Lead: Two Threads.Surface treatment: Bright.Material: HSS - High Speed Steel. BS1127:1950Size: 6mm x 1.00.
A quick and easy way to cut clean imperial sized holes in sheet metal up to 16 gauge. The special design allows an even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches boxed singly without key, which should be ordered separately. To use these punches they require a hole to be drilled through the sheet metal (large enough to clear the heagonal Screw) then the Die and hexagonal screw are threaded through the sheet metal then onto the die nut and screw die nut. When the hexagonal screw is tightened the punch will cut cleanly and evenly through the metal.Size. 7/16 in.Key Type. 3/16 in hexagon wrench
Recoil inserts are the quick and easy way to repair damaged threads or creating stronger original threads in alloys and composite materials in original equipment manufacture.Made from corrosion resistant stainless steel, they create stronger threads in most materials and simplifiy changeover from unified to metric or vice versa. Recoil thread repair kits contain a quality HSS tap, Installation tool, precision stainless steel inserts and instructions.Supplied in a sturdy container.Please note NOT supplied with a tapping drill.ExtensionKit 14.0mm x 1.25Length 1 1/2 X Diameter
Dormer E500 straight flute taps are the only type of taps that can be used by hand, but they may also be used in a machine if required. Extremely versatile, can tap through or blind holes in most materials. When tapping blind holes straight flute taps should be used in sets. The three taps which form a set are known by more than one name. 1. Taper or First tap2. Second or Intermediate tap3. Bottoming, third or plug tap. Metric coarse straight flute taps. Tolerance: Class 2 for 6H FitSurface treatment: BrightMaterial: HSS High Speed SteelChamfer No: 1,2 and 3, Serial no 4 and 5Flute Geometry: Straight Flutes ISO529Size: 3mm x 0.50 Taper.
Faithfull Centre punch with a square head which provides a larger striking area and prevents the punch rolling when laid on the bench. Carefully hardened and tempered and with a 90° ground point.Point Diameter: 2.5mm (3/32in).Length: 100mm (4in).
The Moore & Wright Firm Joint Inside Calipers are manufactured from polished tool steel and have a large headed nut and screw assembly that provides a firm and rigid friction joint, with no play. The sizes listed are the effective leg length which is measured from the joint assembly. The Firm Joint Inside Calipers are manufactured to BS3123 standards. Note: Firm joint caliper capacities are generally 1/3 greater than the effective leg length.The Moore & Wright 3306R Firm Joint Inside Caliper has the following specification: Size: 150mm (6in).
Dormer E500 straight flute taps are the only type of taps that can be used by hand, but they may also be used in a machine if required. Extremely versatile, can tap through or blind holes in most materials. When tapping blind holes straight flute taps should be used in sets. The three taps which form a set are known by more than one name. 1. Taper or First tap2. Second or Intermediate tap3. Bottoming, third or plug tap. Metric coarse straight flute taps. Tolerance: Class 2 for 6H FitSurface treatment: BrightMaterial: HSS High Speed SteelChamfer No: 1,2 and 3, Serial no 4 and 5Flute Geometry: Straight Flutes ISO529Size 3.5mm x 0.6 second
This hollow punch is made from carbon steel. It has a ground tapered section with a milled clearway for removing waste materials. It is intended for cutting soft materials such as leather.
A quick and easy way to cut clean imperial sized holes in sheet metal up to 16 gauge. The special design allows an even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches boxed singly without key, which should be ordered separately. To use these punches they require a hole to be drilled through the sheet metal (large enough to clear the heagonal Screw) then the Die and hexagonal screw are threaded through the sheet metal then onto the die nut and screw die nut. When the hexagonal screw is tightened the punch will cut cleanly and evenly through the metal.Size. 11/16 in.Key Type. 7/32 in hexagonal wrench
These Dormer 2 piece sets each feature a tap and its corresponding pre-hole drill in one convenient package, helping to save time and error.The packs contain an A002 split-point jobber drill and a straight flute tap. The taps are suitable for threading up to 1.5x their diameter in most materials (ISO Standard). Two tap options are available: Second tap for through drilling, or a bottoming tap for blind holes.Specifications: Tap Type: SecondThread Size: M12
Set of 7 Power Grip Screw Extractors have reverse spiral flutes for maximum gripping power. Universal shape fits metric and fractional sizes and features a 1/4in hexagon shank suitable for use with power drills and nut drivers. Made from durable high carbon steel for longer life. Sizes: 3/16in, 1/4in, 8mm (5/16in), 3/8in, 10mm, 11mm (7/16in) and 1/2in.Drive Size: 1/4in.
The Faithfull Engineer's Set has been carefully crafted from high-quality tool steel, these squares are accurate to BS939 Grade B standard. The stock and blade are precision ground to ensure straightness and accuracy, and the spring steel blade is hardened and tempered for increased durability. Set of 4 in a wooden storage case containing 50mm, 75mm, 100mm and 150mm (2in, 3in, 4in, 6in).
Manufactured from high quality C45 carbon steel, this Faithfull tap and die set is suitable for cleaning and cutting threads in mild steel, aluminium and brass. Each set contains a tap wrench, die holder, screwdriver and a range of metric taps and dies, featuring the most commonly used European threads. The Faithfull FAITAPDSET39 39 piece metric tap & die set contains the following: 1 x Tap wrench: M3-121 x Die stock holder: 25mm (1 inch)1 x Screwdriver1 x Screwpitch1 x Tap wrench16 x Metric Taps: 3x0.5mm, 3x0.6mm, 4x0.7mm, 4x0.75mm, 5x0.8mm, 5x0.9mm, 6x0.75mm, 6x1.0mm, 7x0.75mm, 7x1.0mm, 8x1.0mm, 8x1.25mm, 10x1.25mm, 10x1.5mm, 12x1.5mm, 12x1.75mm1 x Tap: 1/8 inch NPT16 x Metric Dies (same sizes as metric taps)1 x Die: 1/8 inch NPT.
The Faithfull Spring Dividers have polished natural steel finish legs made of flat stock. They are carefully balanced, with heat treated points. A strong but flexible bow spring and centrally located adjustment screw give a smooth and precise action.Size 150mm (6 in)
Faithfull Letter and number punches are used for hand marking metals and other hard materials. They are useful for stamping personal identification or post codes on tools, cycles etc., as frequently recommended by police and insurers. The letter or number sizes as shown, relate to the height of the characters. The punches are manufactured from high quality tested carbon steel with double induction hardened heads to ensure high quality impressions. The body is hardened and the head is tempered to prevent chipping when hammered.Contents : 1, 2, 3, 4, 5, 6, 7, 8, 9, 0 (9 is achieved by reversing 6).Set supplied in plastic box.Size : 6mm (1/4 in).
Manufactured from high quality C45 carbon steel, this Faithfull tap and die set is suitable for cleaning and cutting threads in mild steel, aluminium and brass. Each set contains a tap wrench, die holder, screwdriver and a range of metric taps and dies, featuring the most commonly used European threads. The Faithfull FAITAPDSET21 21 piece metric tap & die set contains the following: 1 x Tap wrench: M3-121 x Die stock holder: 25mm (1 inch)1 x Screwdriver8 x Metric Taps: 3 x 0.5mm, 4 x 0.7mm, 5 x 0.8mm, 6 x 1.0mm, 7 x 1.0mm, 8 x 1.25mm, 10 x 1.5mm and 12 x 1.75mm.1 x Tap: 1/8 inch NPT8 x Metric Dies (same sizes as metric taps)1 x Die: 1/8 inch NPT.
Hexagonal bodied parallel pin punches with extra long pins. Used for driving out long retaining pins. The pin should be first started with a hand or taper punch to avoid damage to the point of the pin punch. Pin length: 63mm (2.1/2in).Overall length: 152mm (6in).Size. 4mm (5/32 in).
