Irwin 6X Blue Groove Stubby Wood Bits are ideal for drilling wood and offer 6x faster drilling penetration than a standard flat bit. Their 'Tri-Flute' design allows for faster chip ejection and their full screw tips ensure ease of use and pull through. The cutting spurs produce clean holes with minimal break out and the tapered flute reduces binding. The drill bits are also heat treated for extra durability. Stubby drill bits are 10cm (4in) long, making them ideal for drilling through joists or in enclosed areas. Suitable for holes up to 5cm (2in) deep.Diameter: 20mm.Working length: 50mm (2in).Overall length: 100mm (4in).
Sikkens Cetol HLS Plus Translucent Woodstain is a low build, solvent-borne semi - gloss woodstain that can be used both as a base stain and as a finishing coat. It is highly translucent to bring out the beauty of woodgrain, it protects against mould and algae and is resistant to UV radiation, peeling and cracking. Cetol HLS Plus is also microporous and water-repellent It can be used as a finishing coat on exterior softwood and hardwood substrates such as cladding, fascias, soffits, rough sawn timber and fencing. As a base stain, Cetol HLS plus is readily absorbed into timber to provide a sound base for finishing coats. It can be used alone as a system on cladding, decking and garden furniture or as a base stain before the application of Cetol Filter 7 plus or Cetol THB plus on windows and doors. However it should not be used alone as a finish for hardwood timbers.
These Forgefix Clout Nails have a large head, which distributes the load directly underneath the top of the nail, ensuring that roofing felt stays firm and secure. This reduces the risk of tearing. The nails are galvanised for increased resistance to corrosion.Suitable for roofing of all types. APPLICATION:Specifically used when roofing felt is being fitted to either shed or similar types of roofs. Galvanisation is process of applying a protective zinc coating to steel in order to prevent rusting. Zinc coatings prevent corrosion of the protected metal by forming a physical barrier, and by acting as a sacrificial anode even if this barrier is damaged.Clout Nail Galvanised 40mm Bag Weight 500g
These Faithfull Centre Points are used for accurate alignment of dowel holes. To use: Place the blunt end in a hole already made for dowel in one piece of wood, place the second piece of wood in required position and press down to leave centre of second hole accurately marked.The Faithfull FAIDOWCENT8 contains: 4 x 8 mm dowel points.
Roughneck Wire Brush with 3 rows of large wires. It is 355mm (14in) long and has 19 sets of bristles, an integrated hardened steel scraper and a TPR soft grip handle. This wire brush is ideal for cleaning patios, decking and barbecues, cleaning small parts such as contacts on spark plugs and removing paint and rust from hard surfaces. Comes in: Carbon, Stainless or Brass Wire Bristles.Roughneck ROU52030 Carbon Steel Wire Brush Soft Grip with Scraper 355mm 14in
Medium flexibility grinder pads are recommended for 60+ finer grits. The unique flexibility and durability make these our best selling pad. This range can be considered for universal use. Made in Great BritainType. 90-10MX.To suit. 100 mm Mini Grinders.Thread. M10 x 1.5. Abrasive Disc Size. 100 mm x 16 mm (4in). Machine Fitted:-Black and Decker, Bosch 1347.0, Broomwade 1009, Clarke, Compare BW10011, CP9110, Felisatti, Hitachi, Perles, Ryobi, Stayer. UT8750. Pin spanner - green
Rustins Quick-Drying All Surface All Purpose (ASAP) Paint is a water based paint that dries to a satin finish. It resists flaking or peeling because of its flexible capabilities. ASAP has a low odour and does not require any priming. It is suitable for use on wood, metal, plastic, galvanised steel, uPVC, lead, glass, tiles, plaster, mdf, masonry and melamine.This Rustins ASAP Paint has the following specification: Colour: Cream.Size: 250ml.
The Bahco BAHCOFIT TORX Tip screwdrivers are suitable for TORX head screws. They have 2-component handles with vertical grooves for comfortable grip and maximum force transmission. The screwdrivers' blades are made from high performance alloy steel which is chrome plated and entirely hardened. The black finish tip provides higher accuracy. Each screwdriver has its part number and tip size laser printed for easier identification.Specifications: Tip: TX20.Blade length: 100mm.Total length: 195mm.
Dormer A125 HSS Extra Length Drill is a general purpose extra length drill that is ideal for long reach and deep hole applications and capable of drilling up to 10 times its diameter.
Solvite All Purpose Wallpaper Adhesive is extra strong for reliable, long lasting results. It has a fast mix formula for quick and easy preparation. Extra strong, smooth lump free formula, fast 20 second mix and ready to use in under 2 minutes. For hanging washables, vinyls, lining paper and embossed paper.Size: 10 roll + 50% free.
The Master Lock Aluminium Black Vinyl Cover padlocks are a tough and dependable security solution. With a modern black vinyl finish to the body, they are an appealing solution for day-to-day reliability. Each padlock has a solid body, hardened steel shackle and dual locking levers. A variety of multi-pack options, where all padlocks in the pack open with the same key (keyed alike) are also available. Padlocks are available with 3-pin and 4-pin cylinders and with a variety of shackle lengths for added security and for a wider range of possible application options. The black vinyl cover also helps protect surfaces from scratching. All Master Lock padlocks are supplied with a minimum of 2 keys and a Lifetime Warranty against mechanical failure. Suggested uses: Lockers, trunks, cupboards and sheds.The Master Lock 9130EURTBLK has the following specifications: 2 x 30mm aluminium with black vinyl cover padlocks - 18mm hardened steel shackle, 5mm diameter - 4-pins keyed alike
The ABUS 64TI Series TITALIUM™ Padlocks are ideal for medium to high risk of theft, recommended for a wide range of security requirements. All models in this series have a paracentric keyway and chrome plated cylinder cores. Hardened steel shackle, 30mm and above, with NANO PROTECT™ shackle coating which assures security and high corrosion resistance. TITALIUM™ is based on a special aluminium alloy, a mixture of materials is created that is extremely durable and lightweight; similar to the process used in aircraft construction. Compared to classic brass padlocks, the locks in the TITALIUM™ series are around 30% lighter but feature the same level of security making them excellent value for money. Sizes: 20 to 25mm, ideal for securing bags, suitcases, jewel cases, tool boxes, etc. Sizes 30mm and up, ideal for securing valuables/goods of medium value or at a an average risk of theft.This ABUS 64TI/40 TITALIUM™ Padlock is supplied carded has the following specification: ABUS Security Level: 3. Shackle Width: 22mm.Shackle Height: 23mm.Shackle Diameter: 6mm. Overall Width: 40mm.Overall Height: 62mm.Overall Depth: 15mm.
The Bahco 9629 Series Flat Bit has a positive cutting angle which drills holes twice as fast and lasts three times longer than a conventional bit. Made from high-carbon steel and heat-treated all over. The hardened blade is forged directly from the round shaft. The winged shoulders enable the bit to first cut the wood and then remove the material from the centre section, ensuring a smooth finish and superior swarf clearance.1 x Bahco 9629-12 Flat Bit 12mm
Dowsil™ 781 is a one-part silicone sealant, which has excellent adhesion to a wide range of non-porous surfaces, including: glass, aluminium, painted surfaces and composite boards. It is fast curing and offers excellent resistance to ageing, shrinkage, cracking and discolouring. Suitable for glazing applications, weather sealing of sheet cladding, curtain walls, draught proofing and general internal sealing applications. It is tack-free in one hour with a working time of 5-10 minutes. It is listed by the UK Water Regulations Advisory Scheme (WRAS) for use in contact with potable water once cured. Conforms to ISO 11600-F&G-20LM. 781 has excellent weatherability, with an application temperature range +5 to +40°C and joint movement capability +/– 20%.Dowsil™ 781 Silicone Sealant, Black
Dormer Metric A002 TiN Jobber Drill Bits have a TiN tip coating for increased tool life and performance. It has a self-centring split point for superb hole quality and positional accuracy. It will drill steel, stainless, cast iron, ceramics, plastics and many other materials with ease. Made to DIN 338RN/BS328/ISO 235 standards. PLEASE NOTE ALL sizes under 2.0mm are NOT TiN Coated.Tip diameter: 3.80mm.Working length: 43mm.Overall length: 75mm.
The Stanley FatMax® Fixed Blade Folding Knife has an ergonomic design for comfortable, extended, heavy-duty use. Its soft hand grip and thumb pad ensure comfort and control, whilst its belt clip enables convenient knife transport. The knife has a metal body for added durability. It has an in-built tape cutter for opening boxes without damaging the contents. The knife has a quick blade change mechanism and on board blade storage for convenient and quick blade replacement. Length: 170mm.
The Stanley FatMax® Ergo Aviation Snips with black oxide coated blades, with one serrated edge for grip/anti-slip and one smooth edge for an overall cleaner cutting finish with blade markings for increased precision. They stay sharper longer to deliver up to 20x the cutting life of competitive models, which equates to 50,000 cycles per tool (when cutting 22 gauge stainless steel). Fitted with ergonomic handles that feature a reduced handle span by 20%, to prevent ‘over-stretch’, lowering the stress on the hand and arm muscles. This helps reduce the risk of strain and injury, ultimately less effort is required. Improved handle ergonomics provide better support to the finger and palm grip areas. Constructed from a chrome molybdenum alloy with a tapered front-end design that allows more manoeuvrability, improving accessibility. Improved pivot bolt design for increased durability, the new low profile design helps with restricted access whilst also improving strength. Fitted with a spring loaded latch, making it easier to open/close.1 x Stanley Tools FatMax® Yellow Ergo Aviation Snips Straight Cut 250mm (10in)
A 1992B heavy-duty blade with rounded safety tips - it is ideal for opening cartons without tearing contents and is much safer to use in warehousing or similar environments. Blades fit Springback knife and 99E original Stanley retractable blade knife.
The ABUS 54TI Series TITALIUM™ Padlocks are the entry level padlock of the TITALIUM™ range. They have a solid lock body made from TITALIUM™ aluminium alloy, a mixture of materials is created that is extremely durable and lightweight; similar to the process used in aircraft construction. Fitted with a hardened steel double locking shackle, which resists saw attack, they offer optimum security against lower theft risks. 40mm and above are fitted with a 5 pin tumbler cylinder. They offer optimum security against lower theft risks. Ideal for bags, suitacases, lockers, toolboxes etc.This ABUS 54TI/30 TITALIUM™ Padlock is supplied carded has the following specification: ABUS Security Level: 3. Shackle Width: 15mm.Shackle Height: 14mm.Shackle Diameter: 5mm. Overall Width: 29mm.Overall Height: 45mm.Overall Depth: 13mm.
The Estwing EHB/15 Handy Bar is forged half round for added strength and less weight. It has a wide, thin blade for easy prying. Ideal for carpenters and mechanics.
The Master Lock Excell™ Brass Finish Padlocks are made with cutting edge technology to deliver unprecedented security. They feature tough cut patented octagonal boron carbide shackles which are 50% tougher to cut than hardened steel, and dual ball bearing locking mechanisms for maximum pry resistance. Theses padlocks are built for strength and are made from laminated steel with zinc outer components and a brass finish for weather resistance. They have either a precision 4-pin or 5-pin cylinder and recessed rivets that are chisel resistant. Supplied with 4 keys and a Lifetime Warranty against mechanical failure. Suggested uses: Gates, sheds, storage units, fences, containers and chains.The Master Lock Excell™ Brass Finish Padlock has the following specifications: Size: 50mm.Octagonal Boron Carbide Shackle: 9mm Diameter.Tumbler Cylinder: 4-pin with dual ball bearing locking.
ForgeFix ForgeFast Wood Screws have a universally accepted, Torx® compatible drive. Their recessed ribs provide improved countersinking and reduced surface dust, and their reinforced countersunk necks improve holding power. The screws have a patented drill and drive thread for reduced splitting of the timber, reduced 'jacking' and spinning of joined timber, increased pull-out and a firmer fix. A sharp point provides faster bite and is capable of piercing 0.8mm steel. The screws have an 'Elementech 400' coating providing an anti-corrosive metal finish, which lasts up to 6 times longer than standard zinc coatings. The coating is environmentally friendly and does not contain Cr6+. It is Salt Spray tested to 400 hours. The screws are suitable for interior use. Every box is supplied with a Torx® compatible bit.Size: 6.0 x 240mm.Box quantity: 100.
Unibond Duct Tape is a multi-purpose, heavy-duty, fabric reinforced tape. It uses a high strength adhesive for a long-lasting hold. The tape is water-resistant and ideal for binding, repairing and reinforcing. It adheres to multi-surfaces. This heavy-duty adhesive tape has hundreds of uses around the home, car and garden and is suitable for both interior and exterior use. No need for scissors as the tape can be easily torn by hand.Size: 50mm x 50m. Colour: Black.
The Knipex Ear Clamp Plier is for simple and reliable mounting of 1-ear and 2-ear clamps (Oetiker system or similar). The head is made from high-grade special tool steel, forged and oil-hardened. Black atramentized finish with polished tips. Durable and strong, the press points on the clamp are extremely tough. Fitted with dipped plastic coated handles. The slim head permits good accessibility in confined areas. Versatile use, ideal for clamps on CV boots, cooler and fuel lines, air pressure systems, compressors. Length: 220mm
For filing flat surfaces, sharp corners and shoulders as well as for deburring. A double cut file should be used for work in high-alloy tool steels. Also useful for the sharpening of heavy implements. High removal rate. Double cut on both sides - with one safe edge (a safe edge permits work in corners). Parallel sides but slightly tapered in thickness.Size 300mm (12in)Cut: hand smooth.Tanged.
A 45-piece kit supplied in a weatherproof four pocket travel bag with handle and belt clips. Suitable for use in the home and outdoors to treat burns, grazes and cuts. Contents: 1 x Triangular Bandage1 x Finger Dressing2 x Eye Wash 20ml10 x Assorted Clear Waterproof Plasters1 x Conforming Stretch Bandage1 x Medium Dressing2 x Burns Sachets2 x Burns Bandages2 x Adhesive Wound Dressings4 x Assorted Double Sided Non Adherent Wound Dressings5 x Pairs Disposable Vinyl Gloves1 x ReviveAid Mouth Piece4 x Moist Wipes1 x Pair of Scissors1 x Microporous Tape6 x Safety Pins
The Roughneck R28M Hardpoint Concrete Saw is made from thick, premium grade steel for rigidity. With large, induction hardened punched teeth. The saw is fitted with a double injected, soft grip handle for comfort and hand protection. The handle is shaped to allow 90° and 45° markings. Suitable for cutting cellular concrete, breeze blocks, bricks, etc. Normal wear and tear of the blade is not covered by the 10 year guarantee. Specification: Length: 700mm (28in)Teeth: 1.2TPI
Liberon Hard Wax Oil is a blend of premium quality oil and wax to give superior protection to wooden flooring and furniture. Maintaining the natural look of the wood, it forms a highly durable barrier on soft and hardwoods against water, stains, heat, dirt and wear and tear. Hard Wax Oil is particularly well suited to humid environments such as kitchens and bathrooms, but can be used throughout the home. It can be applied to bare wood or previously oiled wood. The matt or satin finish is washable with mild detergent and tools can be easily cleaned with water. Hard Wax Oil is pleasant to use and does not have a strong odour. Preparation:The wood must be bare, clean and dry.Varnished, painted or waxed wood: Remove all old varnish, paint or wax with stripper or sand the surface back to bare wood. Clean and remove all dust.Oiled wood: Sand lightly with 240 grit paper and remove all dust.Bare wood: Clean, sand lightly with 240 grit paper and remove all dust. Application:Stir the contents of the tin well before use. Apply the first coat thinly with a brush or roller and leave to dry for 8 hours. Then sand with 240 grit paper and remove all dust. Apply a second coat in the same way as the first and leave to dry for 24 hours. The final finish can vary depending on the type of wood, especially with hardwoods.Specifications:Colour: Clear.Finish: Matt.Size: 2.5 Litres.
A Victorinox Swiss Army Knife is a combination of solid hand tool and inventive creativity. A characteristic feature of the Victorinox Swiss Army Knife is its multi-functionality, which makes it indispensable for many of life's situations. All Victorinox Swiss Army Knives are made from first class stainless steel and are guaranteed against any defects in material and workmanship. The Handyman Swiss Army Knife has large and small blades, a corkscrew, a can opener with a small 3 mm screwdriver, a bottle opener with a 6 mm screwdriver and wire stripper, a reamer/punch tool, a keyring, tweezers, a toothpick, scissors, a multi-purpose hook, a wood saw, a chisel, a nail file with a metal file, a nail cleaner and a metal saw, a fine screwdriver and pliers with wire cutters and a wire crimping tool. Colour: Red.Size: 91mm (3.1/2in) long.
These Forgefix Set Screws are made from grade 8.8 steel and are zinc plated for increased resistance to corrosion. They are fully threaded and conform to DIN 933 standards.Can be used with many Nut types and washers. APPLICATION:For fastening together numerous types of material or to be fastened in to pre-tapped holes.Widely used in many engineering applications. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminum and stainless steels by their oxide layers.High Tensile Set Screw ZP M6 x 20 Bag 10
The DEWALT Impact Torsion Pozi Bits have a 15° torsion zone that allows the screwdriver bit to flex rather than break, and the full fit head prevents rounding of the screw head and prevents 'cam out' (bit head slipping out of the screw head due to the turning force). The magnetic screw lock enables tasks to be completed quicker and easier, reducing instances of dropped or lost screws. Supplied in packs of 2, 5 or 15.DEWALT Impact Torsion Bits PZ1 50mm Pack of 5
Cuprinol Woodworm Killer (WB) kills all types of wood-boring beetle larvae. Its deep penetration ensures effective protection for years to come. This low odour, water based formula has been specially developed to make it more pleasant and convenient to use. Application: Bare Wood: Flood surfaces with 2 or 3 brush coats. Pay particular attention to endgrain, corners, joints, crevices, etc. In severe cases, also inject into flight holes 7-10cm (3-4ins) apart and repeat treatment. Re-treat surfaces cut after treatment. Polished Wood: Inject into flight holes 5-7cm (2-3ins) apart. Flood into joints. Wipe off surplus. In severe cases repeat treatment. Fluid does not penetrate polished surfaces. Wax polished surfaces will normally require re-waxing after treatment. Note: The application of this product may cause darkening of some timbers. If colour is critical, try a test area first and allow to dry fully to ensure final appearance is acceptable. After drying, glues, fillers and knotting can be used normally. Bitumen, rubber and some plastic based materials may soften or swell on contact with fluid or solvent vapour.Do not spill on asphalt, bitumen, bitumen felt, tar or mastics. Ensure timber is fully dry (allow 6-8 weeks) or use a vapour barrier such as heavy-duty polythene sheets (as used for damp proof membrane) before laying plastic floor tiles, foam or rubber-backed carpet, underlay or hanging vinyl wallpaper.Cuprinol Low Odour Woodworm Killer Size: 1 Litre.
The Moldex M5 Earmuffs are flexible and lightweight with an appealing, stylish design. Seamless workmanship make these earmuffs robust and durable with grip points for easy on-head adjustment. They also feature a smooth sliding mechanism for size adjustment. The extra soft foam air cushions and low contact pressure ensure the M-Series are extremely comfortable. Has a signal to noise ratio (SNR) of 34 dB.
The Irwin HSS Pro TiN drill bits are primarily designed for drilling metal and harder, tougher alloys. Compared to traditional HSS twist drill bits, speed can be increased by 40 -60% and feed by 10 -20% without reducing the life time of the drill bit significantly. TiN is also a poor conductor of heat, so the heat generated during the drilling process is diverted into the chips and coolant and less into the drill bit. These drills have a 135° split point grinding tip which ensures perfect centring and reduced drilling pressure. The drill bit body is manufactured from high quality HSS steel coated with 2.5µ Titanium Nitride (TiN), the TiN coating has a hardness of app. 80 HRC and is very resistant to wear. TiN has a low coefficient of friction, this results in less power being consumed and less heat generated during the drilling.The Irwin IRW10502585 HSS Pro TiN Coated Drill Bit comes in the following:Size: 4.5 x 80mm
This 16 litre easy carry knapsack sprayer is manufactured from shatterproof and frost resistant materials and is suitable for use with most water-based garden and household chemicals and pesticides. The sprayer’s large capacity and 'pump as you go' pressure action helps make light work of those big spraying jobs, making it ideal for use in larger gardens. The lance features an adjustable spray nozzle with a trigger lock for continuous use when required. A curved back and adjustable twin shoulder straps help make the sprayer comfortable to wear when in use. Supplied complete with full service pack with three assorted spray nozzles.
Ronseal Multi Purpose Wood Filler can be applied straight from the tube and gives professional, long-lasting, tough and durable repairs. The flexible formula resists shrinking and cracking, and it can be stained, varnished or painted. Suitable for both interior and exterior use. Once dry, simply sand then stain, varnish or paint over. Ideal for use on doors, window frames, screw/nail holes, cracks, gaps, skirting boards, floors and other wooden surfaces. Available in various shades and sizes. Specification: Application: Filling KnifeDrying Time: 2 hours approx.Protection Level: High1 x Ronseal Multi Purpose Wood Filler Tube Natural 100g
