Bostitch 28 Galvanised Ring Shank Stick Nails 2.8 X 50Mm Pack Of 2000

Description

Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments.

28° Collation Angle

Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out.

(Remember only tools fitted with sequential trip should be used when working up a ladder).

Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them.

Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater.

Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish.

Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.

Type - Stick nail Ring
Gauge/Diameter (mm) 2.8
Length 50
Collation Angle 28 Degrees
SKU S280R50G8
Profile RING
Finish G8
Description STICK NAIL 2.80-50 RING GAL8 2M
Qty per box 2000

Note: This nail will also fit the N80SB, FW28WW-E, N100S

Bostitch 28 Galvanised Ring Shank Stick Nails 2.8 X 50Mm Pack Of 2000

Product form

£63.49 Incl. VAT

    Be quick! Only 5 products left in stock!

    • Shipped today? Order within: Nov 02, 2024 14:00:00 +0000
    • Free UK Shipping No Minimum Spend*
    • 5 Star Reviews Across All Our Retail Channels
    • Multiple Secure Payment Options
    • 100% Genuine Products
    Delivery

    Next Day Delivery available Monday - Friday when you order by 2pm.

    We take delivery very seriously. You can find the UK delivery time for any of our products on the relevant product page. These vary based on complexity of shipping, size/value of the item and the service used. These times are a guideline - however, in well over 99% of cases (and rising), we achieve or beat them.

    DELIVERY PRICES

    We offer free delivery throughout mainland UK and Northern Ireland. *This excludes certain items that are difficult to ship and some special offers. ‘Mainland UK’ is defined by the delivery area set by our couriers - although geographically belonging to the mainland we do have to charge a delivery fee to some parts of the Scottish Highlands and other outer lying areas given the increased costs charged by couriers for despatch to these areas. We do however attempt to keep these costs to our customers as low as possible.

    *Please note - this may vary for non-mainland UK addresses. You can always check the delivery cost of an order by adding items to your shopping cart and using the ‘Estimate Shipping & Tax’ tool.

    To find out more about delivery prices/methods please click here.

    Returns & Refunds

    We know that you will be pleased with your purchases from Trade Hut Direct however, there may be occasions when you will need to return items to us. If you wish to do so, please thoroughly read our returns policy and complete the returns form here.

    Important - if your return qualifies for a refund of the return carriage costs, please be aware that the maximum we can refund is £6. If the return costs are going to be more than this, please call our customer service team who should be able to arrange an alternative solution.

    To find out more about returns and refunds please click here.

    Payments

    We accept all major credit/debit cards.

    If you have any questions relating to placing an order, how to pay or issues with checking out please contact our customer service team on 0800 994 9992.

    SKU: BOSS280R50G8
    Barcode: 5902013926023

    Description

    Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments.

    28° Collation Angle

    Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out.

    (Remember only tools fitted with sequential trip should be used when working up a ladder).

    Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them.

    Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater.

    Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish.

    Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.

    Type - Stick nail Ring
    Gauge/Diameter (mm) 2.8
    Length 50
    Collation Angle 28 Degrees
    SKU S280R50G8
    Profile RING
    Finish G8
    Description STICK NAIL 2.80-50 RING GAL8 2M
    Qty per box 2000

    Note: This nail will also fit the N80SB, FW28WW-E, N100S

    Recently viewed products

    Login

    Forgot your password?

    Don't have an account yet?
    Create account