Zinsser CoversUp™ Aerosol is a low odour vertical aerosol that is a stain killer and ceiling touch-up paint in one. It seals water damaged ceilings and sprays vertically for ease of use. It’s perfect for touch up when you don’t want to repaint the entire ceiling due to spot damage. Zinsser’s stain blocking primer technology is incorporated into this new generation product that offers a flat white finish that matches most new acoustical ceiling tiles and white ceiling paints. CoversUp™ is an odourless solvent based formula with only a brief odour from propellants that diminishes quickly. Specification Size: 400ml.Colour: White.
Zinsser's Cover Stain® is an interior / exterior primer, sealer, stain sealer and bond coat that dries for recoat in only two hours.On interior surfaces, Cover Stain® dries quickly and has great hiding power, providing outstanding stain killing and enamel undercoating performance. Stains of all kinds are permanently sealed so topcoats are blemish free.Cover Stain® is especially effective on nicotine and water stains. New wood trim can be primed, sanded and top coated the same day, saving time and money. On exterior surfaces, Cover Stain® has a unique formulation that delivers full penetration and flexibility on all surfaces, especially dimensionally unstable wood panelling and trim, where few oil-based primers can succeed. It resists cracking and peeling and is compatible with all decorative top coats. The primer is white in colour, but can also be tinted to mid-tone colours. It can be applied via an airless sprayer, brush, pad or roller. Application information: Coverage: 9.8m² per Litre. Touch dry: 35 minutes. Hard dry: 4 - 7 days. Recoatable: 2 hours.Zinser CSP500 Cover Stain® is supplied in the following:Container type: Tin. Volume: 500ml.
Zinsser's Cover Stain® is an interior / exterior primer, sealer, stain sealer and bond coat that dries for recoat in only two hours.On interior surfaces, Cover Stain® dries quickly and has great hiding power, providing outstanding stain killing and enamel undercoating performance. Stains of all kinds are permanently sealed so topcoats are blemish free.Cover Stain® is especially effective on nicotine and water stains. New wood trim can be primed, sanded and top coated the same day, saving time and money. On exterior surfaces, Cover Stain® has a unique formulation that delivers full penetration and flexibility on all surfaces, especially dimensionally unstable wood panelling and trim, where few oil-based primers can succeed. It resists cracking and peeling and is compatible with all decorative top coats. The primer is white in colour, but can also be tinted to mid-tone colours. It can be applied via an airless sprayer, brush, pad or roller. Application information: Coverage: 9.8m² per Litre. Touch dry: 35 minutes. Hard dry: 4 - 7 days. Recoatable: 2 hours.Zinsser CSP400A Cover Stain® is supplied in the following:Container type: Aerosol. Volume: 400ml.
Zinsser's Cover Stain® is an interior / exterior primer, sealer, stain sealer and bond coat that dries for recoat in only two hours.On interior surfaces, Cover Stain® dries quickly and has great hiding power, providing outstanding stain killing and enamel undercoating performance. Stains of all kinds are permanently sealed so topcoats are blemish free.Cover Stain® is especially effective on nicotine and water stains. New wood trim can be primed, sanded and top coated the same day, saving time and money. On exterior surfaces, Cover Stain® has a unique formulation that delivers full penetration and flexibility on all surfaces, especially dimensionally unstable wood panelling and trim, where few oil-based primers can succeed. It resists cracking and peeling and is compatible with all decorative top coats. The primer is white in colour, but can also be tinted to mid-tone colours. It can be applied via an airless sprayer, brush, pad or roller. Application information: Coverage: 9.8m² per Litre. Touch dry: 35 minutes. Hard dry: 4 - 7 days. Recoatable: 2 hours.Zinser CSP25L Cover Stain® is supplied in the following:Container type: Tin. Volume: 2.5 Litres.
Zinsser's Cover Stain® is an interior / exterior primer, sealer, stain sealer and bond coat that dries for recoat in only two hours.On interior surfaces, Cover Stain® dries quickly and has great hiding power, providing outstanding stain killing and enamel undercoating performance. Stains of all kinds are permanently sealed so topcoats are blemish free.Cover Stain® is especially effective on nicotine and water stains. New wood trim can be primed, sanded and top coated the same day, saving time and money. On exterior surfaces, Cover Stain® has a unique formulation that delivers full penetration and flexibility on all surfaces, especially dimensionally unstable wood panelling and trim, where few oil-based primers can succeed. It resists cracking and peeling and is compatible with all decorative top coats. The primer is white in colour, but can also be tinted to mid-tone colours. It can be applied via an airless sprayer, brush, pad or roller. Application information: Coverage: 9.8m² per Litre. Touch dry: 35 minutes. Hard dry: 4 - 7 days. Recoatable: 2 hours.Zinser CSP1L Cover Stain® is supplied in the following:Container type: Tin. Volume: 1 litre.
Zinsser Ceiling Pro 5-in-1 is based on ground-breaking paint technology that effortlessly provides a perfectly finished ceiling every time. It adheres to any surface, seals stains (including water and smoke), primes and finishes whilst bridging hairline cracks. In addition Ceiling Pro 5-in-1 contains a biocide that protects the dried coating against fungal degradation, prolonging the life of the painted ceiling. These outstanding features combine with a 1 hour recoat time, low odour and ultra low VOC content. Suitable for both bare and previously painted ceilings.
Zinsser's B-I-N® is the ultimate shellac-based primer, sealer and stain killer. It is perfect for use on interior surfaces and spot priming of exterior surfaces. B-I-N® offers unparalleled adhesion to glossy surfaces – including glass – without the need for scuff sanding and blocks stubborn and persistent stains. The high adhesion shellac formula seals porous surfaces with excellent enamel holdout, even sealing bleeding knots and sap streaks. B-I-N® works brilliantly on water stains, mildew stains, nicotine, oil stains, marker pens stains and more. B-I-N® permanently blocks every kind of odour (from smoke and fire damage to odours from pets and nicotine). Its dried film is non-toxic and hypo-allergenic, and it may be used in areas where incidental contact with food items occur. The primer is white in colour, but can also be tinted to mid-tone colours. It can be applied via an airless sprayer, brush, conventional sprayer or roller. Perfect for interior ceilings, walls, doors and related paintable surfaces and spot priming on exterior metal, trims, PVC and wood. Application information: Coverage: 12.5m² per litre.Touch dry: 15 minutes.Hard dry: 1 - 3 days.Recoatable: 45 minutes.Zinsser BIN500 is supplied in the following:Container type: Tin.Volume: 500ml.
Zinsser's B-I-N® is the ultimate shellac-based primer, sealer and stain killer. It is perfect for use on interior surfaces and spot priming of exterior surfaces. B-I-N® offers unparalleled adhesion to glossy surfaces – including glass – without the need for scuff sanding and blocks stubborn and persistent stains. The high adhesion shellac formula seals porous surfaces with excellent enamel holdout, even sealing bleeding knots and sap streaks. B-I-N® works brilliantly on water stains, mildew stains, nicotine, oil stains, marker pens stains and more. B-I-N® permanently blocks every kind of odour (from smoke and fire damage to odours from pets and nicotine). Its dried film is non-toxic and hypo-allergenic, and it may be used in areas where incidental contact with food items occur. The primer is white in colour, but can also be tinted to mid-tone colours. It can be applied via an airless sprayer, brush, conventional sprayer or roller. Perfect for interior ceilings, walls, doors and related paintable surfaces and spot priming on exterior metal, trims, PVC and wood. Application information: Coverage: 12.5m² per litre.Touch dry: 15 minutes.Hard dry: 1 - 3 days.Recoatable: 45 minutes.Zinsser BIN400A is supplied in the following:Container type: Aerosol.Volume: 400ml.
Zinsser's B-I-N® is the ultimate shellac-based primer, sealer and stain killer. It is perfect for use on interior surfaces and spot priming of exterior surfaces. B-I-N® offers unparalleled adhesion to glossy surfaces – including glass – without the need for scuff sanding and blocks stubborn and persistent stains. The high adhesion shellac formula seals porous surfaces with excellent enamel holdout, even sealing bleeding knots and sap streaks. B-I-N® works brilliantly on water stains, mildew stains, nicotine, oil stains, marker pens stains and more. B-I-N® permanently blocks every kind of odour (from smoke and fire damage to odours from pets and nicotine). Its dried film is non-toxic and hypo-allergenic, and it may be used in areas where incidental contact with food items occur. The primer is white in colour, but can also be tinted to mid-tone colours. It can be applied via an airless sprayer, brush, conventional sprayer or roller. Perfect for interior ceilings, walls, doors and related paintable surfaces and spot priming on exterior metal, trims, PVC and wood. Application information: Coverage: 12.5m² per litre.Touch dry: 15 minutes.Hard dry: 1 - 3 days.Recoatable: 45 minutes.Zinsser BIN25L is supplied in the following:Container type: Tin.Volume: 2.5 litres.
Zinsser's Bulls Eye® 1-2-3 Plus is a universal water-based primer, sealer and stain killer. It is ideal for interior and exterior painting projects. Bulls Eye® 1-2-3 Plus delivers performance benefits normally only associated with solvent-based primers, including exceptional adhesion and stain blocking. It is specially formulated to resist re-wetting, meaning it can block water soluble stains like a solvent-based primer and seal oil-soluble stains, meaning painting projects can be completed with just one primer. Uniquely, it can be applied directly over water and smoke stains. Thanks to Hydro Pliolite® resin, Bulls Eye® 1-2-3 Plus delivers unparalleled adhesion and deals effortlessly with hard to paint interior and exterior substrates such as glossy surfaces, ceramic tiles, galvanised metal, vinyl, hardboard, melamine, varnish, plastic, GRP, UPVC, wood, masonry and more. Bulls Eye® 1-2-3 Plus is rust inhibitive and ideal for new metal. It resists flash rusting in its 'wet' state – and provides rust resistance for the life of the coating. It dries to a smooth, tight, water-resistant film that is perfect for painting iron railings, steel doors, metal panels, duct work, galvanised gutters – any interior or exterior metal surface. Bulls Eye® 1-2-3 Plus is mould and mildew-resistant, making it ideal for high-humidity areas such as bathrooms and laundry rooms. It offers effective resistance to the formation of mould and mildew on the underside and surface of the primer film, prolonging the life of your paint job. All of the above benefits combine with ultra low VOC content, a lightning quick drying time of just 30 minutes and a 1 hour recoat time. Bulls Eye® 1-2-3 Plus is white in colour and can be applied via airless sprayer, brush, conventional spray, pad or roller. Application information:Coverage: 10m² per Litre. Touch dry: 35 minutes. Hard dry: 7 days. Recoatable: 1 hour.Zinsser BE123P25L Bullseye 1-2-3 Plus is supplied in the following:Container type: Tin. Volume: 2.5 Litres.
Zinsser's B-I-N® is the ultimate shellac-based primer, sealer and stain killer. It is perfect for use on interior surfaces and spot priming of exterior surfaces. B-I-N® offers unparalleled adhesion to glossy surfaces – including glass – without the need for scuff sanding and blocks stubborn and persistent stains. The high adhesion shellac formula seals porous surfaces with excellent enamel holdout, even sealing bleeding knots and sap streaks. B-I-N® works brilliantly on water stains, mildew stains, nicotine, oil stains, marker pens stains and more. B-I-N® permanently blocks every kind of odour (from smoke and fire damage to odours from pets and nicotine). Its dried film is non-toxic and hypo-allergenic, and it may be used in areas where incidental contact with food items occur. The primer is white in colour, but can also be tinted to mid-tone colours. It can be applied via an airless sprayer, brush, conventional sprayer or roller. Perfect for interior ceilings, walls, doors and related paintable surfaces and spot priming on exterior metal, trims, PVC and wood. Application information: Coverage: 12.5m² per litre.Touch dry: 15 minutes.Hard dry: 1 - 3 days.Recoatable: 45 minutes.Zinsser BIN1L is supplied in the following:Container type: Tin.Volume: 1 litre.
Zinsser's Bulls Eye® 1-2-3 Plus is a universal water-based primer, sealer and stain killer. It is ideal for interior and exterior painting projects. Bulls Eye® 1-2-3 Plus delivers performance benefits normally only associated with solvent-based primers, including exceptional adhesion and stain blocking. It is specially formulated to resist re-wetting, meaning it can block water soluble stains like a solvent-based primer and seal oil-soluble stains, meaning painting projects can be completed with just one primer. Uniquely, it can be applied directly over water and smoke stains. Thanks to Hydro Pliolite® resin, Bulls Eye® 1-2-3 Plus delivers unparalleled adhesion and deals effortlessly with hard to paint interior and exterior substrates such as glossy surfaces, ceramic tiles, galvanised metal, vinyl, hardboard, melamine, varnish, plastic, GRP, UPVC, wood, masonry and more. Bulls Eye® 1-2-3 Plus is rust inhibitive and ideal for new metal. It resists flash rusting in its 'wet' state – and provides rust resistance for the life of the coating. It dries to a smooth, tight, water-resistant film that is perfect for painting iron railings, steel doors, metal panels, duct work, galvanised gutters – any interior or exterior metal surface. Bulls Eye® 1-2-3 Plus is mould and mildew-resistant, making it ideal for high-humidity areas such as bathrooms and laundry rooms. It offers effective resistance to the formation of mould and mildew on the underside and surface of the primer film, prolonging the life of your paint job. All of the above benefits combine with ultra low VOC content, a lightning quick drying time of just 30 minutes and a 1 hour recoat time. Bulls Eye® 1-2-3 Plus is white in colour and can be applied via airless sprayer, brush, conventional spray, pad or roller. Application information:Coverage: 10m² per Litre. Touch dry: 35 minutes. Hard dry: 7 days. Recoatable: 1 hour.Zinsser BE123P1L Bullseye 1-2-3 Plus is supplied in the following:Container type: Tin. Volume: 1 Litre.
Zinsser's Bulls Eye® 1-2-3 is a universal interior and exterior, water-based, primer-sealer. It offers low odour application, quick drying convenience and excellent adhesion to glossy surfaces. Bulls Eye® 1-2-3 effectively primes and seals a wide variety of interior and exterior surfaces. A ‘bond coat’ primer that’s great for hard-to-stick surfaces, it offers excellent adhesion without sanding. Bulls Eye® 1-2-3 also prevents rust formation when applied over clean ferrous metal such as iron and steel. It is mould and mildew-resistant, making it ideal for high-humidity areas such as bathrooms and laundry rooms. It offers effective resistance to the formation of mould and mildew on the underside and surface of the primer film, prolonging the life of the paint job. Bulls Eye® 1-2-3 is great for blocking stains. It permanently and completely seals graffiti, grease spots, tar and asphalt – inside and out. It is rust inhibitive and ideal for new metal. It resists flash rusting in its 'wet' state and provides rust resistance for the life of the coating. It dries to a smooth, tight, water-resistant film that is perfect for painting iron railings, steel doors, metal panels, duct work, galvanised gutters – any interior or exterior metal surface. Bulls Eye® 1-2-3 is white in colour and can be applied via air sprayer, brush, conventional spray, pad or roller. It has a quick 35 minute drying time and 1 hour dry time and can be tinted towards the colour of your topcoat (mid-tone colours only) to eliminate the need for one coat of paint – saving both time and money. Application information: 10m² per Litre. Touch dry: 35 minutes. Hard dry: 7 days. Recoatable: 1 hour.The Zinsser BE1231L Bulls Eye 1-2-3 is supplied in the following: Container type: Tin. Volume: 1 Litre.
Zinsser's Bulls Eye® 1-2-3 is a universal interior and exterior, water-based, primer-sealer. It offers low odour application, quick drying convenience and excellent adhesion to glossy surfaces. Bulls Eye® 1-2-3 effectively primes and seals a wide variety of interior and exterior surfaces. A ‘bond coat’ primer that’s great for hard-to-stick surfaces, it offers excellent adhesion without sanding. Bulls Eye® 1-2-3 also prevents rust formation when applied over clean ferrous metal such as iron and steel. It is mould and mildew-resistant, making it ideal for high-humidity areas such as bathrooms and laundry rooms. It offers effective resistance to the formation of mould and mildew on the underside and surface of the primer film, prolonging the life of the paint job. Bulls Eye® 1-2-3 is great for blocking stains. It permanently and completely seals graffiti, grease spots, tar and asphalt – inside and out. It is rust inhibitive and ideal for new metal. It resists flash rusting in its 'wet' state and provides rust resistance for the life of the coating. It dries to a smooth, tight, water-resistant film that is perfect for painting iron railings, steel doors, metal panels, duct work, galvanised gutters – any interior or exterior metal surface. Bulls Eye® 1-2-3 is white in colour and can be applied via air sprayer, brush, conventional spray, pad or roller. It has a quick 35 minute drying time and 1 hour dry time and can be tinted towards the colour of your topcoat (mid-tone colours only) to eliminate the need for one coat of paint – saving both time and money. Application information: 10m² per Litre. Touch dry: 35 minutes. Hard dry: 7 days. Recoatable: 1 hour.The Zinsser BE12325L Bulls Eye 1-2-3 is supplied in the following: Container type: Tin. Volume: 2.5 Litres.
Zinsser ALLCOAT® Exterior is the best performance all surface paint. Designed for the long term decoration of timber, metal, masonry, plastic, concrete, cladding and more, it forms a Vapour permeable, low maintenance water-shedding coating, re-coatable in 1 hour. ALLCOAT® Exterior contains a biocide to protect the dried coating against fungal degradation. Designed for all exterior surfaces, ALLCOAT® Exterior is ideal for new or previously painted wood, UPVC, galvanising, metals, cladding, weathered bitumen, stucco, brick, stone, cured concrete and more. ALLCOAT® Exterior is self-priming and will bond to existing glossy paints without sanding. For most jobs, there is no need to purchase a separate primer. After removing existing mould and mildew, two coats of ALLCOAT® Exterior will ensure that any exterior looks bright and beautiful for years. Zinsser ALLCOAT® Exterior gives excellent resistance against: Cracking, blistering and flaking.Rain and severe weather. Features:Long lasting finish.Easy to apply.Excellent colour retention.Multi-surface application. Surfaces should be clean, dry, sound and free of any contamination that may interfere with adhesion. Remove all loose or peeling paint and chalky paint residue. Sand edges of any remaining paint film until smooth. Special precautions should be taken during surface preparation of pre- 1960 paint surfaces as they may contain harmful lead. Avoid the inhalation of dust. Wear a suitable face mask if dry sanding. New concrete, masonry and other related surfaces must be cured at least 30 days before priming. Remove all existing mould and mildew before painting.This Zinsser ALLCOAT® Exterior has the following specification: Size: 2.5 LitreColour: White Application Shake or stir well before using. Apply with synthetic bristle brush, roller or sprayer. For airless spraying, use a .017in tip and high-medium (2000-2500 PSI) pressure. Apply when air and surface temperatures are between 10°-32°C and humidity is less than 85%. Avoid painting in direct sunlight and maintain a wet edge to avoid lapping.
Zinsser ALLCOAT® Exterior is the best performance all surface paint. Designed for the long term decoration of timber, metal, masonry, plastic, concrete, cladding and more, it forms a Vapour permeable, low maintenance water-shedding coating, re-coatable in 1 hour. ALLCOAT® Exterior contains a biocide to protect the dried coating against fungal degradation. Designed for all exterior surfaces, ALLCOAT® Exterior is ideal for new or previously painted wood, UPVC, galvanising, metals, cladding, weathered bitumen, stucco, brick, stone, cured concrete and more. ALLCOAT® Exterior is self-priming and will bond to existing glossy paints without sanding. For most jobs, there is no need to purchase a separate primer. After removing existing mould and mildew, two coats of ALLCOAT® Exterior will ensure that any exterior looks bright and beautiful for years. Zinsser ALLCOAT® Exterior gives excellent resistance against: Cracking, blistering and flaking.Rain and severe weather. Features:Long lasting finish.Easy to apply.Excellent colour retention.Multi-surface application. Surfaces should be clean, dry, sound and free of any contamination that may interfere with adhesion. Remove all loose or peeling paint and chalky paint residue. Sand edges of any remaining paint film until smooth. Special precautions should be taken during surface preparation of pre- 1960 paint surfaces as they may contain harmful lead. Avoid the inhalation of dust. Wear a suitable face mask if dry sanding. New concrete, masonry and other related surfaces must be cured at least 30 days before priming. Remove all existing mould and mildew before painting.This Zinsser ALLCOAT® Exterior has the following specification: Size: 1 LitreColour: White Application Shake or stir well before using. Apply with synthetic bristle brush, roller or sprayer. For airless spraying, use a .017in tip and high-medium (2000-2500 PSI) pressure. Apply when air and surface temperatures are between 10°-32°C and humidity is less than 85%. Avoid painting in direct sunlight and maintain a wet edge to avoid lapping.
Zinsser ALLCOAT® Exterior is the best performance all surface paint. Designed for the long term decoration of timber, metal, masonry, plastic, concrete, cladding and more, it forms a Vapour permeable, low maintenance water-shedding coating, re-coatable in 1 hour. ALLCOAT® Exterior contains a biocide to protect the dried coating against fungal degradation. Designed for all exterior surfaces, ALLCOAT® Exterior is ideal for new or previously painted wood, UPVC, galvanising, metals, cladding, weathered bitumen, stucco, brick, stone, cured concrete and more. ALLCOAT® Exterior is self-priming and will bond to existing glossy paints without sanding. For most jobs, there is no need to purchase a separate primer. After removing existing mould and mildew, two coats of ALLCOAT® Exterior will ensure that any exterior looks bright and beautiful for years. Zinsser ALLCOAT® Exterior gives excellent resistance against: Cracking, blistering and flaking.Rain and severe weather. Features:Long lasting finish.Easy to apply.Excellent colour retention.Multi-surface application. Surfaces should be clean, dry, sound and free of any contamination that may interfere with adhesion. Remove all loose or peeling paint and chalky paint residue. Sand edges of any remaining paint film until smooth. Special precautions should be taken during surface preparation of pre- 1960 paint surfaces as they may contain harmful lead. Avoid the inhalation of dust. Wear a suitable face mask if dry sanding. New concrete, masonry and other related surfaces must be cured at least 30 days before priming. Remove all existing mould and mildew before painting.This Zinsser ALLCOAT® Exterior has the following specification: Size: 2.5 LitreColour: Black Application Shake or stir well before using. Apply with synthetic bristle brush, roller or sprayer. For airless spraying, use a .017in tip and high-medium (2000-2500 PSI) pressure. Apply when air and surface temperatures are between 10°-32°C and humidity is less than 85%. Avoid painting in direct sunlight and maintain a wet edge to avoid lapping.
Zinsser ALLCOAT® Exterior is the best performance all surface paint. Designed for the long term decoration of timber, metal, masonry, plastic, concrete, cladding and more, it forms a Vapour permeable, low maintenance water-shedding coating, re-coatable in 1 hour. ALLCOAT® Exterior contains a biocide to protect the dried coating against fungal degradation. Designed for all exterior surfaces, ALLCOAT® Exterior is ideal for new or previously painted wood, UPVC, galvanising, metals, cladding, weathered bitumen, stucco, brick, stone, cured concrete and more. ALLCOAT® Exterior is self-priming and will bond to existing glossy paints without sanding. For most jobs, there is no need to purchase a separate primer. After removing existing mould and mildew, two coats of ALLCOAT® Exterior will ensure that any exterior looks bright and beautiful for years. Zinsser ALLCOAT® Exterior gives excellent resistance against: Cracking, blistering and flaking.Rain and severe weather. Features:Long lasting finish.Easy to apply.Excellent colour retention.Multi-surface application. Surfaces should be clean, dry, sound and free of any contamination that may interfere with adhesion. Remove all loose or peeling paint and chalky paint residue. Sand edges of any remaining paint film until smooth. Special precautions should be taken during surface preparation of pre- 1960 paint surfaces as they may contain harmful lead. Avoid the inhalation of dust. Wear a suitable face mask if dry sanding. New concrete, masonry and other related surfaces must be cured at least 30 days before priming. Remove all existing mould and mildew before painting.This Zinsser ALLCOAT® Exterior has the following specification: Size: 1 LitreColour: Black Application Shake or stir well before using. Apply with synthetic bristle brush, roller or sprayer. For airless spraying, use a .017in tip and high-medium (2000-2500 PSI) pressure. Apply when air and surface temperatures are between 10°-32°C and humidity is less than 85%. Avoid painting in direct sunlight and maintain a wet edge to avoid lapping.
The Wagner SteamForce Pro Wallpaper Steamer is hard-wearing and durable. The powerful motor produces lots of steam, meaning it can penetrate through several layers of wallpaper at once. Suitable for removing all wallpaper types including multi-layered, painted and Artex™ using steam. The roll cage features a unique patented built-in step that provides a strong working platform. It has an extra large anodised water tank that can hold up to 7.5 litres of water, for up to 90 minutes steam time. It also includes a 5m long steam hose for a large working range. Ideal for professional users. Specification: Input Power: 2,750WTank: 7.5 litreMax. Running Time: 90 min.Heat Up Time: 18 min.Hose Length: 5mSteam Plate Size: 253 x 305mm & 140 x 70mmMains Cable: 5mWeight: 9.4kg
The Vitrex Power Max Tile Saw has a 560 Watt, high torque, direct drive motor which produces a constant cutting speed for ultra smooth cuts. It has adjustable, double extension arms to support larger format tiles and the cutting table tilts to allow mitre cuts. The tile saw has an integral ruler and adjustable rip guide for accurate, straight cuts. To prevent overheating, it has thermal overload protection, as well as a water cooling system with a large reservoir. Supplied with a 180mm x 16mm diamond blade with a continuous rim for extra clean cuts. Suitable for 16mm and 22mm bore blades. Specification Input Power: 560 Watt.No Load Speed: 3,000/min.Blade Size: 180mm.Cutting Depth: @90°: 30mm, @45°: 17mm.
The Vitrex TL T001 Tile Lifter enables easy handling of non-porous tile, marble and glass during installation. Its vacuum lifts and holds up to 25kgs (55lbs), making it ideal for larger format tiles.
The Vitrex TILEKIT001 Tiling Kit contains the following: 1 x Grout and Sealant Smoother that has a moulded plastic handle with flexible insert. Provides a professional finish to most household sealant applications. Ideal for baths, basins, sinks, worktops, window frames etc. 1 x Dual Purpose Grouting Sponge is a large 2-in-1 sponge ideal for cleaning and polishing tiles. Rounded edges to prevent accidental removal of fresh grout. 1 x Grout Float features a premium rubber pad mounted on a rigid polyurethane base with integral handle. Ideal for fast even grouting of large areas. 1 x Wall & Floor Notched Adhesive Trowel with a hard, cold rolled steel blade and a high impact plastic handle, to offer excellent durability. Size: 100 x 230mm (9 x 4in).Notches: Square: 6mm, Round 20mm.
The Vitrex TA S100 Tile Adhesive Scraper is ideal for scraping residue off subfloors, windows and walls and is great for wallpaper removal. Supplied complete with 100mm blade.
The Vitrex PT S001 Super Sponge is a professional heavy-duty extra large sponge suitable for big clean up jobs from tiling and grouting clean up to plastering and drywall wipe down. Unique hydrophilic design holds up to 4 times more liquid than standard sponges. The rounded edges minimise digging out or marring of grout.
The Vitrex MTC1200 is a professional manual tile cutter for cutting ceramics and tiles of up to 1200mm in length. It is suitable for heavy-duty applications, with interior bearings for high precision. Its cutting wheel is made from tungsten carbide. Capacity:Tile length: 1200mm.Tile depth: 18mm.
These Vitrex Long Leg Spacers provide an easy way to achieve a more professional tiling finish. They ensure a constant and even spacing of tiles, allowing for the specified size in grout line. The tiles spacers have easily breakable legs for T-shape spacers. They are easier to handle than standard tile spacers and allow for a 2mm grout line. Supplied in a resealable bag.Vitrex LLS5500 Long Leg Spacer Size: 5mm. Pack Size: 500.
These Vitrex Long Leg Spacers provide an easy way to achieve a more professional tiling finish. They ensure a constant and even spacing of tiles, allowing for the specified size in grout line. The tiles spacers have easily breakable legs for T-shape spacers. They are easier to handle than standard tile spacers and allow for a 2mm grout line. Supplied in a resealable bag.Vitrex LLS5250 Long Leg Spacer Size: 5mm. Pack Size: 250.
These Vitrex Long Leg Spacers provide an easy way to achieve a more professional tiling finish. They ensure a constant and even spacing of tiles, allowing for the specified size in grout line. The tiles spacers have easily breakable legs for T-shape spacers. They are easier to handle than standard tile spacers and allow for a 2mm grout line. Supplied in a resealable bag.Vitrex LLS4500 Long Leg Spacer Size: 4mm. Pack Size: 500.
These Vitrex Long Leg Spacers provide an easy way to achieve a more professional tiling finish. They ensure a constant and even spacing of tiles, allowing for the specified size in grout line. The tiles spacers have easily breakable legs for T-shape spacers. They are easier to handle than standard tile spacers and allow for a 2mm grout line. Supplied in a resealable bag.Vitrex LLS4250 Long Leg Spacer Size: 4mm. Pack Size: 250.
These Vitrex Long Leg Spacers provide an easy way to achieve a more professional tiling finish. They ensure a constant and even spacing of tiles, allowing for the specified size in grout line. The tiles spacers have easily breakable legs for T-shape spacers. They are easier to handle than standard tile spacers and allow for a 2mm grout line. Supplied in a resealable bag.Vitrex LLS3500 Long Leg Spacer Size: 3mm.Pack Size: 500.
These Vitrex Long Leg Spacers provide an easy way to achieve a more professional tiling finish. They ensure a constant and even spacing of tiles, allowing for the specified size in grout line. The tiles spacers have easily breakable legs for T-shape spacers. They are easier to handle than standard tile spacers and allow for a 2mm grout line. Supplied in a resealable bag.Vitrex LLS3250 Long Leg Spacer Size: 3mm. Pack Size: 250.
These Vitrex Long Leg Spacers provide an easy way to achieve a more professional tiling finish. They ensure a constant and even spacing of tiles, allowing for the specified size in grout line. The tiles spacers have easily breakable legs for T-shape spacers. They are easier to handle than standard tile spacers and allow for a 2mm grout line. Supplied in a resealable bag.Vitrex LLS31500 Long Leg Spacer Size: 3mm. Pack Size: 1500.
These Vitrex Long Leg Spacers provide an easy way to achieve a more professional tiling finish. They ensure a constant and even spacing of tiles, allowing for the specified size in grout line. The tiles spacers have easily breakable legs for T-shape spacers. They are easier to handle than standard tile spacers and allow for a 2mm grout line. Supplied in a resealable bag.Vitrex LLS2500 Long Leg Spacer Size: 2mm. Pack Size: 500.
These Vitrex Long Leg Spacers provide an easy way to achieve a more professional tiling finish. They ensure a constant and even spacing of tiles, allowing for the specified size in grout line. The tiles spacers have easily breakable legs for T-shape spacers. They are easier to handle than standard tile spacers and allow for a 2mm grout line. Supplied in a resealable bag.Vitrex LLS2250 Long Leg Spacer Size: 2mm.Pack Size: 250.
These Vitrex Long Leg Spacers provide an easy way to achieve a more professional tiling finish. They ensure a constant and even spacing of tiles, allowing for the specified size in grout line. The tiles spacers have easily breakable legs for T-shape spacers. They are easier to handle than standard tile spacers and allow for a 2mm grout line. Supplied in a resealable bag.Vitrex LLS22000 Long Leg Spacer Size: 2mm. Pack Size: 2000.
