Zinsser Gardz® Sealer Primer is a clear, water-based, acrylic resin sealer that penetrates deeply into porous surfaces. It dries fast, and forms a hard, moisture-proof film that prevents drywall blistering and bubbling. It binds down chalky surfaces, strengthens soft texture finishes, and seals in residual wallpaper paste. Gardz® Sealer Primer can be applied to high-pH surfaces, and is easily cleaned up with soap and water. Recommended Uses: Damaged Drywall: prevents bubbles that form when damaged drywall is skim coated with spackling or joint compound. It penetrates and seals damaged facing paper, restoring it to a sound surface for repairs, suitable for painting or wallcovering. New Drywall / Joint Compound and Spackling: new gypsum drywall, joint compound and spackling are very porous and can make finish coatings appear splotchy and uneven. It penetrates and uniformly seals, creating a moisture resistant film that protects drywall from blistering, tearing and other damage when redecorating in the future. Plaster: freshly applied plaster is extremely porous but also extremely alkaline with a pH of 12.0 or more in many cases. Allow new plaster to cure at least 24 hours before applying. Before priming old, bare plaster, be sure to determine that the surface is clean, dry and in sound condition, taking care to repair any cracks or holes with spackling paste or joint compound before sealing the surface. Calcimine: is a very old form of plaster that is extremely chalky and water-sensitive. It penetrates calcimine more effectively than oil-base coatings and has a much lower odour. Because it resists moisture, it prevents water-based topcoat paint or texture finishes from softening up calcimine layers underneath. Wallpaper Adhesive Residue: water-based coatings or texture finishes will reactivate old wallpaper adhesive, resulting in cracking and peeling. Formulated to completely seal in residual adhesive and prevent it from ruining water-based topcoats and texture finishes. Texture and Popcorn Finishes: Can be used to seal textured walls and popcorn ceilings before applying water base primer or paint. It penetrates soft or crumbly texture material and hardens it, creating a durable, water resistant barrier that prevents primer or paint from softening texture material underneath. Old Wallpaper: most of the wallpaper installed before the 1960’s was true paper, with no vinyl coating. To determine if the wallcovering is a true paper wipe a wet sponge across the surface, if the water is readily absorbed it means there is no vinyl coating. This type of wallcovering can be effectively sealed. First, peel away any loose or frayed edges, or whatever remains should be firmly adhered to the wall. Apply as you would to any other wall surface. Pre-Wallcovering Primer: penetrates, seals, sizes and protects drywall facing paper and skim coat, providing a properly sealed surface for new wallcovering. At redecorating time, it protects the surface of the drywall when the old wallcovering is stripped off. Builder’s Flat Paint: penetrates chalky, builder’s flat paint and binds it to the wall, providing water-resistant protection from paint, wallcovering and texture finishes.Zinsser Gardz® Sealer Primer 1 Litre Colour: Clear.Size 1 Litre.
Zinsser's Bulls Eye® 1-2-3 is a universal interior and exterior, water-based, primer-sealer. It offers low odour application, quick drying convenience and excellent adhesion to glossy surfaces. Bulls Eye® 1-2-3 effectively primes and seals a wide variety of interior and exterior surfaces. A ‘bond coat’ primer that’s great for hard-to-stick surfaces, it offers excellent adhesion without sanding. Bulls Eye® 1-2-3 also prevents rust formation when applied over clean ferrous metal such as iron and steel. It is mould and mildew-resistant, making it ideal for high-humidity areas such as bathrooms and laundry rooms. It offers effective resistance to the formation of mould and mildew on the underside and surface of the primer film, prolonging the life of the paint job. Bulls Eye® 1-2-3 is great for blocking stains. It permanently and completely seals graffiti, grease spots, tar and asphalt – inside and out. It is rust inhibitive and ideal for new metal. It resists flash rusting in its 'wet' state and provides rust resistance for the life of the coating. It dries to a smooth, tight, water-resistant film that is perfect for painting iron railings, steel doors, metal panels, duct work, galvanised gutters – any interior or exterior metal surface. Bulls Eye® 1-2-3 is white in colour and can be applied via air sprayer, brush, conventional spray, pad or roller. It has a quick 35 minute drying time and 1 hour dry time and can be tinted towards the colour of your topcoat (mid-tone colours only) to eliminate the need for one coat of paint – saving both time and money. Application information: 10m² per Litre. Touch dry: 35 minutes. Hard dry: 7 days. Recoatable: 1 hour.The Zinsser BE123500 Bulls Eye 1-2-3 is supplied in the following: Container type: Tin. Volume: 500ml.
The Vitrex SP R500 Spiked Roller helps to remove bubbles caused by entrapped air in floor levelling compounds. It is ideal for subfloor preparation and includes a splash guard to minimise mess.Width: 500mm.
The Vitrex 10 2962 Large Tile Squeegee has a strong flexible plastic blade with squeegee edge for rapid grouting. A contoured handle provides extra comfort.
Vitrex 102912 Grout Clean Up and Polishing Kit provides an easy way to clean and polish tiles. The kit includes a blue, plastic handle with 4 interchangeable pads to suit most applications. The pads are coloured for easy identification. Ideal for removing excess grout and grout film and for polishing tiles. Weight: 98g.
The Vitrex 10 2420 Grout Rake has a tungsten carbide grit edged blade for longer life. It is fitted with a durable nylon handle designed for extra grip. For removing old and discoloured grout.
The Vitrex 10 2277 Combination Spreader has a convenient dual purpose design. With a notched edge for fast adhesive application and a squeegee edge for rapid grouting.
The Vitrex 102207 Tile Saw has an extra deep steel frame for improved cutting access. Its 150mm tungsten carbide blade, cuts in any direction. Outlasts conventional hacksaw blades by up to 10 times. Soft-grip handle for extra comfort. Cutting depth of 150mm - to the centre of a 300mm tile. Spare Blade (VIT102203)
This Stanley Roller Sleeve is made from Microfibre fabric which provides great all-round performance with a smooth finish. It is ideal for varnishes, water and oil-based paint and is suitable for smooth and semi-rough surfaces. Size: 230mm (9in).Pile Height: 12mm.Diameter: 44mm (1.3/4in).
Stanley Microfibre Roller Sleeves provide a great all-round finish and are ideal for varnishes, water-based and oil-based paints. They can be used on smooth and semi-rough surfaces and create minimal splatter.This set includes a storage paint tray that keeps paint fresh for up to 7 days. Contents:1 x Microfibre Roller Sleeve: 230 x 38mm (9 x 1.1/2in)1 x Soft Grip Cage Frame.1 x Storage Paint Tray.
This Stanley decorators sponge is ideal for washing down walls, decorating and household use. Made from synthetic material, it is long lasting and very absorbent.
The Stanley Hobby paint brush has pure black bristles and a rust resistant ferrule. The yellow polypropylene handle is shaped for comfort.Size: 50 mm (2in).
This mini roller kit is suitable for use with all emulsion and wood stains. Ideal for small area work and perfect for touching up paintwork. Microfibre technology enables up to twice the paint coverage with minimal splatter. Supplied with a 100 mm (4in) microfibre refill.
Rustins Yacht varnish is specially formulated on Tung Oil to give maximum protection and durability to marine and other external woodwork. It has excellent adhesion and will not flake or peel when correctly applied. Ideal for exterior doors and window frames. Gloss or satin finish. Conforms to the Toys (Safety) Regulations 1995, BS:EN71 Part 3.Rustins Yacht Varnish Gloss.Size: 500 ml.
Rustins Xylene Thinners can be used to thin most oil based paints. Ideal for use with Damp Seal and High Heat Paint. Xylene Thinners can also be used to clean brushes and any other equipment which has been used with oil based paints.Size: 500ml.
Rustins Floor Oil is a mixture of natural vegetable oils and resins which improve the colour of bare wood. Gives a soft lustrous, durable finish. Allow 4-8 hours between coats. Can be applied to all types of interior wooden floors including parquet, woodblock and floorboards.Rustins Floor Oil.Size: 5 Litre.
Rustins Foam Brush Set is an alternative to bristle brushes. The poly brush is ideal for paint, wood dye, oils and varnish. Quick and easy-to-use and clean, they leave no brush marks or bristles and are suitable for both water and oil based products. Sizes included: 1, 2, 3 and 4in.
The Ronseal Ultra Tough clear varnish range is an ultra-tough polyurethane varnish which provides a rich, clear, mellow finish to interior wood that is ideal for use over wood dyes. The varnish is heat, water and scratch-resistant with long-lasting protection against knocks, and most household chemicals in the home. This product provides long hard wearing protection on wood and is suitable for any bare or previously treated wood. Application: Brush.Drying time: 2-4 hours.Coverage: 24 square metres covered per litre.Protection Level: Very High.Areas of use: Wooden interior furniture and trim including doors, shelving, skirting boards, cork, hardboard or chipboard.The Ronseal RSLUTVHG750 comes in the following:Size: 750ml.Finish - Clear Gloss Hardglaze.
Ronseal Ultimate Protection Decking Oil provides superior, natural looking protection, for a longer lasting finish. The unique formula penetrates deeper into the wood to provide increased durability. Providing a lightly tinted finish it will give double the weather resistance and foot traffic protection versus standard decking oils. Unique, new to the market, water-based Linseed Oil technology, colours and waterproofs your deck in one easy step. Gives a more natural look to your deck and is rainproof in 90 minutes, recoat in 4 hours. Primarily for use on pre-treated decking. Preparation - Untreated, weathered decking: For untreated grey and weathered wood, use Ronseal Decking Restorer to restore the deck's natural colour and provide a sound base for application which ensures the oil penetrates effectively. Previously finished decking: Use Ronseal Decking Cleaner and Reviver to remove any dust, grease, oil, mildew, algae and other contaminants. Remove any loose, flaking or peeling coatings. To avoid patchiness, and if using a contrasting colour, make sure you remove all previous finishes using Ronseal Decking Stripper. Ensure cut ends are adequately protected using Ronseal Decking End Grain Preserver. New wood: New decking should be allowed to weather naturally (usually 6 months). This will make sure any pre-treatment has eroded allowing the stain to penetrate and adhere to the deck. Clean the deck with Ronseal Decking Cleaner and Reviver using a scrubbing brush to open the pores of the wood and remove any contamination from the manufacture of the timber. Rinse thoroughly with clean water ideally using a pressure washer. Allow to dry fully before over coating. Test effectiveness of the cleaning by splashing the deck with water. If beading occurs, re-clean. Retest before applying any oil. The shade label indicates approximate colour only. It is recommended that you test a small area to determine the final colour which may be influenced by the texture, grain, colour, porosity, type of wood and any previous treatment.This Ronseal Ultimate Decking Oil has the following specification: Colour: Natural.Size: 5 Litre.
Ronseal Diamond Hard Doorstep Paint restores and rejuvenates brick, concrete, stone and wood to give ultra tough protection and additional slip resistance. There's no primer required and it resists knocking, scuffing and scraping and provides protection from oil, grease and water. Have a smarter and safer doorstep. Incredibly hard wearing, Doorstep Paint that takes foot traffic in its stride giving you a non-slip finish for years. Ideal for use on interior and exterior brick, concrete, stone and wood. Not suitable for ceramic floor tiles. Areas of use: Brick, stone or concrete steps.Approx coverage: 12 square metres covered per litre.Average number of coats: 2.Finish: Satin.Application: Brush, Roller.Drying time approx: 2 hours.Protection level: Very High. Two Colours Available: Red or Black.
Colron Refined Teak Oil is a high quality blend of natural resins and oils, which penetrate deeper into the wood grain than standard teak oils replacing essential oils that prevent the wood from drying, warping and splitting. It enriches the wood's natural patina while providing protection from the inside out, making it ideal for use on both interior and exterior wood. Size: 500ml.
The Purdy® XL™ Elite™ Monarch™ Paint Brush is recommended for use with emulsion paint. Its thicker filaments will pick up and lay off more paint for better productivity on the job. Designed by UK professionals specifically for the UK market, ensuring it's Purdy's most versatile and trusted brush. Material: Chinex & Orel Blend Synthetic FilamentsHandle: BeavertailFerrule: Round Edge1 x Purdy® XL™ Elite™ Monarch™ Paint Brush 1.1/2in
The Lessmann Universal Hand Brushes have been designed for the DIY enthusiast and are useful for many cleaning operations. Size: 260 x 28mm. 056.301: 0.3 Crimped Steel Wire.056.501: 0.3 Stainless Steel Wire.056.701: 0.3 Brass Wire.The Lessmann Universal Hand Brush has the following specification: Wire: Crimped Steel.Wire Gauge: 0.3.
Popular with both industrial and DIY users, Wire Scratch Brushes are used for removing rust, corrosion, paint and primer and for generally producing a clean surface. These Faithfull Wire Brushes have unique curved profiles and narrow faces, making them ideal for accessing hard-to-reach places. The high density wire fill and contoured plastic handle allow users to apply a higher pressure than that of a conventional wire brush. Fitted with colour coded handles with hanging slots.The FAIWBHANDS Wire Scratch Brush has the following specifications: Handle colour: Red. Wire: Steel.
A Faithfull easy to use Tile Scribe fitted with a Tungsten Carbide Tipped blade that will provide a long working life. The scribe is suitable for scoring ceramic wall and floor tiles prior to snapping to size and features a contoured handle that provides a firm grip and helps maintain the correct blade angle when scribing. HOW TO USE:Mark the tile to be cut and place it face up on a solid surface. Place a steel rule on the tile and line the ends up with your cut marks. Draw the tile scribe firmly along the rule to score the tile. Thick tiles may need extra attention at the edges, score these independently if required. Place the scored tile on to a flat surface with a piece of thin wire directly underneath the scored line and line up the wire with the score mark at the top and bottom of the tile. Once positioned correctly, apply pressure to both edges of the tile at the same time to snap the tile.
The Faithfull plastic window and glass scraper ideal for removing paint from window frames and windows. Utilises a heavy-duty trimming knife blade. Comes complete with blade and blade guard.With the blade guard attached, the scraper can be used to clear ice off windscreens.Spare blades: FAITKB10 or FAITKB10UKBlade width: 60mm.
The Faithfull FAISUCPAD2 double pad suction lifter is ideal for carrying heavy, awkward items such as glass, doors, windows and sheet metal. It is made from ABS with 120mm rubber gripping pads for maximum hold. This suction lifter securely grips on glass and similar non-porous surfaces. The vacuum system will support loads of up to 45kg (99lbs) when used in a vertical orientation and up to 30kgs (66lbs) when used in a horizontal orientation. Care should always be taken when calculating the total load to be lifted. The Faithfull FAISUCPAD2 double pad suction lifter has a 5 year guarantee.
The Faithfull Single Pad Suction Lifter allows easy handling of non-porous tiles, marble and glass during installation. It is ideal for larger format tiles. The suction lifter is made from ABS plastic with a 120mm rubber gripping pad for maximum hold. The vacuum system will support loads of up to 30kg (66lbs) when used in a vertical orientation and up to 15kgs (33lbs) when used in a horizontal orientation. Care should always be taken when calculating the total load to be lifted.
Faithfull range of quality scratch brushes, manufactured using a heavy-duty plastic handle with a soft grip coating. The ergonomically designed handles are comfortable to use and provide good clearance for the hand from the work surface. Each brush has a high density bristle content at both ends where the most force is focused when in use, for a better performance and longer working life. Brushes are available in 4 types, carbon steel, stainless steel, brass and plastic. Each brush has 4 x 16 rows of bristles.Steel, ideal for general use for removing rust, scale and old paint work.
Dense foam roller refills for use with gloss and emulsion paints on smooth surfaces for a fine finish. For use with both mini rollers and radiator rollers.Size : 100mm Type : FoamPack quantity : 10
These Faithfull Utility Paint Brushes are made 100% synthetic filaments and are suitable for use with all types of paint. The brushes feature a rust-resistant ferrule and a contoured handle for greater user comfort.Size: 25mm (1in).
A mix of synthetic and top quality pure natural bristle with a long bristle length and a comfortable plastic handle, give these Faithfull Paint Brushes perfect balance and make them ideal for use by tradesmen or by the discerning home user. These brushes will provide a high quality finish with all paints. Faithfull paintbrushes are manufactured to the highest standard using the very best materials. The bristles are bonded using top quality resin to avoid any shedding. The plastic handle is fitted with a rustproof stainless steel ferrule.1 x Faithfull Contract Paint Brush 19mm (3/4in)
Evo-Stik white Tile A Wall Fast Set Grout For Ceramic Tiles is a cement-based powder grouting material, suitable for finishing joints of internal and external ceramic tile installations. When set, Evo-Stik Tile A Wall Fast Set Grout For Ceramic Tiles is completely water-resistant and will not wash out of joints. It is recommended for joints up to about 3 mm wide. Suitable for ceramics, mosaics and natural stone walls, ideal for interior uses including kitchens, bathrooms and showers, it is easy to mix with water and sets to leave a professional finish that is resistant to mould growth. 1kg of powder, when mixed, will grout approximately 5m². Coverage is dependent on the nature of the substrate, the adhesive bed thickness and the type of tile.
Everbuild Raw Linseed Oil is a traditional wood treatment for use on cricket bats, oak beams etc. and as a lubricant in the French polishing industry. Size: 500ml.
