Forgefix TechFast Roofing Sheets to Steel Hex Screws are used for joining metal roofing panels to steel frame buildings. The screws are fire resistant and corrosion resistant. Protected by Elementech corrosion resistant coating, salt spray tested to 1000 hours. Complies with EU Safety, Health and Environmental requirements. They are supplied with 16mm EPDM rubber washers.These Forgefix TechFast Roofing Sheets to Steel Hex Screws have the following specification: Size: 5.5 x 45mmEffective Thread Length: 28mmPack Size: 100Drill Tip: No.3 No.3 drill tip for self-drilling in heavy gauge steel up to 5mm.
The Forgefast Hexagonal/Torx® Compatible Timber Screws are suitable for fixing into soft or hardwood. They have a combination hexagonal head with a deep Torx® compatible insert that reduces cam-out, also provides higher torque levels and a firmer drive. Its super sharp tip gives immediate bite from the very first turn. A patented self-drilling thread removes the need to pre-drill the timber and reduces the probability of splitting, even when screwing close to the edge. Hardened case and core give exceptional strength. Protected by elementech 2000 surface treatment which provides corrosion resistance up to 30 times longer than some standard zinc coated screws. They are highly resistant to pull out, they can flex by up to 35°, reducing likelihood of the screw shearing when used in flexible materials. CE approved for use in load-bearing timber construction. Available in a green or tan treated finish.Forgefast Hexagonal/Torx® Compatible Timber Screws Size: 7 x 65mm.Pack Size: Tub of 50.Finish: Green elementech 2000.
These Forgefix TechFast Roofing Screws are designed for use in joining timber to steel and for light section purlins. They have a Torx, countersunk head to sit flush to the surface. The self-drilling point enables speedy insertion, and the wings create a clearance hole in the timber to eliminate the chance of 'jacking' when fixing. The screws are zinc plated and have an 'Elementech' coating for superior anti-corrosion, which has been salt spray tested to 1,000 hours. These light section roofing screws are suitable for fixing timber to steel thicknesses of 1.5mm to 4mm. Each pack is supplied with a free Torx bit.The TFCL5585 TechFast Roofing Screws have the following specifications: Size: 5.5 x 85mm.Pack quantity: 50.
Forgefix TechFast Composite Panels to Steel Hex Screws are used to join composite panels to steel frame buildings. They have a specially designed compression control thread to prevent damage and denting of panels. They are fire and corrosion resistant, protected by Elementech corrosion resistant coating, salt spray tested to 1000 hours. Complies with EU Safety, Health and Environmental requirements. They are supplied with 16mm EPDM rubber washers.These Forgefix TechFast Composite Panels to Steel Hex Screws have the following specification: Size: 5.5 x 125mmInsulation Thickness: 32-90mmPack Size: 100Drill Tip: No.5 No.5 drill tip for self-drilling in heavy gauge steel up to 12.5mm.
These Forgefix Multi-Purpose Pozi Screws with countersunk heads have a zinc finish for increased durability. The screws are immensely popular and versatile, and used in all trades including joinery, electrical and plumbing. Also widely used in DIY applications. APPLICATIONSuitable for use with many materials including PVCu, Timber, Chipboard, MDF, and other similar types. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminium and stainless steels by their oxide layers. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. The countersunk head is designed to sink flush with substrates to leave a smooth surface finish. They have single threads, designed to offer higher pull out values and quicker insertion.Specifications: Size: 5 x 400mm.Box quantity: 200.
Forgefix TechFast Composite Panels to Steel Hex Screws are used to join composite panels to steel frame buildings. They have a specially designed compression control thread to prevent damage and denting of panels. They are fire and corrosion resistant, protected by Elementech corrosion resistant coating, salt spray tested to 1000 hours. Complies with EU Safety, Health and Environmental requirements. They are supplied with 19mm EPDM rubber washers.These Forgefix TechFast Composite Panels to Steel Hex Screws have the following specification: Size: 5.5 x 185mmInsulation Thickness: 92-150mmPack Size: 50Drill Tip: No.5 No.5 drill tip for self-drilling in heavy gauge steel up to 12.5mm.
ForgeFix ForgeFast Wood Screws have a universally accepted, Torx® compatible drive. Their recessed ribs provide improved countersinking and reduced surface dust, and their reinforced countersunk necks improve holding power. The screws have a patented drill and drive thread for reduced splitting of the timber, reduced 'jacking' and spinning of joined timber, increased pull-out and a firmer fix. A sharp point provides faster bite and is capable of piercing 0.8mm steel. The screws have an 'Elementech 400' coating providing an anti-corrosive metal finish, which lasts up to 6 times longer than standard zinc coatings. The coating is environmentally friendly and does not contain Cr6+. It is Salt Spray tested to 400 hours. The screws are suitable for interior use. Every box is supplied with a Torx® compatible bit.Size: 3.5 x 30mm.Box quantity: 200.
Forgefix TechFast Timber to Steel CSK/Wing Screws are used to join timber to steel frame buildings. The screws are fitted with breakaway wings that create a clearance hole to protect thread from engaging timber when drilling through. Breakaway wings will ream a hole, then break-off when they contact the metal surface to be drilled. The thread will then engage with metal. They have a TORX® compatible insert for a higher transmission of power. With improved countersinking from recessed ribs. Fire and corrosion resistant. Complies with EU Safety, Health and Environmental requirements.These Forgefix TechFast Timber to Steel CSK/Wing Screws have the following specification: Size: 5.5 x 40mmClamping Thickness: 20mmEffective Thread Length: 19mmPack Size: 100Drill Tip: No.3 No.3 drill tip for self-drilling heavy gauge steel up to 5mm.
The ForgeFix Spectre Screws are advanced multipurpose wood screws with double countersunk heads and pozi compatible recess. They have a sawtooth thread design to prevent splitting and reamer to prevent jacking. The screws have a zinc yellow passivated finish for excellent resistance to corrosion. The zinc yellow passivation process of electroplating is similar to the 'galvanised' and 'zinc plated' processes but with the addition of a yellow dye. It offers an aesthetically pleasing finish.Specification: Size: 4.0 x 70mmThread: 42mm lengthPack Quantity: Box of 500
Forgefix TechFast Composite Panels to Steel Hex Screws are used to join composite panels to steel frame buildings. They have a specially designed compression control thread to prevent damage and denting of panels. They are fire and corrosion resistant, protected by Elementech corrosion resistant coating, salt spray tested to 1000 hours. Complies with EU Safety, Health and Environmental requirements. They are supplied with 19mm EPDM rubber washers.These Forgefix TechFast Composite Panels to Steel Hex Screws have the following specification: Size: 5.5 x 100mmInsulation Thickness: 28-79mmPack Size: 100Drill Tip: No.3 No.3 drill tip for self-drilling in heavy gauge steel up to 5mm.
These Forgefix TechFast Roofing Screws are designed for use in joining timber to steel and for light section purlins. They have a Torx, countersunk head to sit flush to the surface. The self-drilling point enables speedy insertion, and the wings create a clearance hole in the timber to eliminate the chance of 'jacking' when fixing. The screws are zinc plated and have an 'Elementech' coating for superior anti-corrosion, which has been salt spray tested to 1,000 hours. These light section roofing screws are suitable for fixing timber to steel thicknesses of 1.5mm to 4mm. Each pack is supplied with a free Torx bit.The TFCL5550 TechFast Roofing Screws have the following specifications: Size: 5.5 x 50mm.Pack quantity: 100.
These Forgefix General Purpose Pozidrive Screws with Countersunk heads are zinc plated for increased durability. They are an extremely popular general purpose screw, and suitable for use in and with many materials. APPLICATION:Ideal for use in many ironmongery, electrical and plumbing applications.Can be used with various screw cover caps. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminium and stainless steels by their oxide layers. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. The countersunk head is designed to sink flush with substrates to leave a smooth surface finish. They have twin threads, which enable an easy start when driving. Imperial Size > MetricNo.4 = 3.0mm, No.6 = 3.5mm, No.7 = 3.9mmNo.8= 4.0mm, No.10 = 5.0mm, No.12 = 6.0mmGeneral Purpose Pozi Screw Countersunk TT ZP 2 3/4 x 8 Box 100
These Forgefix Pozidriv Self-Tapping Screws are zinc plated for increased resistance to corrosion. Their Pan Head, with a flat under head surface makes the screw ideal to lay flat on sheet material of all types, thus reducing deformation. The screws tap their own thread in a pre-drilled pilot hole, in sheet metal. The screws are single threaded to resist pull-out. APPLICATIONIdeal for use in many DIY, ironmongery, engineering, electrical and plumbing applications. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminum and stainless steels by their oxide layers. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver.Self Tapping Screw Pozi Pan Head ZP 1 x 6 Box 200
These Forgefix Pozidriv Self-Tapping Screws have countersunk heads and are Zinc Plated for increased resistance to corrosion. They tap their own thread in to a pre-drilled pilot hole in sheet or solid material. They are single threaded to resist pull-out. APPLICATION:Ideal for use in many DIY, ironmongery, engineering, electrical and plumbing applications. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminium and stainless steels by their oxide layers. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. Countersunk heads are designed to sink flush with substrates to leave a smooth surface finish.Self Tapping Screw Pozi Countersunk ZP 1 x 8 Box 200
Forgefix TechFast Metal Roofing Panels to Timber Hex Screws are used to join metal roofing panels to timber frame buildings. They have a specially designed compression control thread to prevent damage and denting of panels. No pre-drilling is required and the self-drilling T17 Gash Point on screws makes for a rapid installation. The nails are fire and corrosion resistant, protected by Elementech corrosion resistant coating, salt spray tested to 1000 hours. Complies with EU Safety, Health and Environmental requirements. They are supplied with 16mm EPDM rubber washers.These Forgefix TechFast Metal Roofing to Timber Screws have the following specification: Size: 6.3 x 80mmSteel Thickness: 0.5-1.2mmHead Type: 8mm HexPack Size: 100
These Forgefix Socket Screws have a raised head, and are designed for attaching electrical wall sockets and switches. The screws have a slotted head and are nickel plated for increased durability. APPLICATIONUsed specifically for attaching electrical wall socket and switches to back plates. The Nickel plating process coats mild steel or stainless steel to considerably prolong the part’s life. Nickel plating is probably the most corrosion resistant finish available and is often used on socket screws for electric switch sockets avoiding corrosion and cross contamination. It leaves a bright aesthetic finish and is extremely hardwearing. With slotted screwdrivers it is important to ensure that the tip matches the width of the screw slot, otherwise you run the risk of damaging the screw head. Slotted screwdrivers are available with either Flared or Parallel tips. For the majority of uses the Flared tip is ideal but if the screw needs to be driven below the material surface a Parallel tip screwdriver should be used. Raised heads have both countersunk and raised structure which is designed for aesthetic purposes on all types of ironmongery and lighting applications.Socket Screw Slotted Raised Head Nickle Plated 3.5 x 75mm Bag 100
These Forgefix Phillips, Single Coarse Thread (SCT) Drywall Screws have a black phosphate finish for increased durability. Their Bugle Head allows the screw to sink effortlessly into the dry lining without the need for countersinking, which in turn minimises the damage to the surface. They are supplied collated, with 50 screws per strip and 1,000 screws per box. APPLICATION:Designed for fitting dry lining to studding. Phosphate coatings are made up of thin crystalline layers of phosphate compounds that adhere to the surface of the fixing or fastener. The phosphate crystals are porous and can be formed from zinc, manganese, or iron phosphate solutions. Phosphate coatings offer good corrosion resistance and have an excellent ability to absorb supplementary coatings which improves appearance, corrosion resistance and resistance to abrasion. The Phillips screw has four simple tapered slots. It is designed so that a Phillips tip screwdriver can turn a screw with increasing torque. When the torque gets to be too strong for the tip then the screwdriver tip winds itself out of the screw thus preventing over-tightening and or damage to the screw head. Coarse thread screws (mainly drywall screws) have an extremely sharp point and are designed to penetrate plasterboard skin. The coarse thread eases in to the board then the timber baton holding the board firm.Drywall Collated Screw Phillips Bugle Head SCT 3.9 x 38mm Box 1000
ForgeFix ForgeFast Wood Screws have a universally accepted, Torx® compatible drive. Their recessed ribs provide improved countersinking and reduced surface dust, and their reinforced countersunk necks improve holding power. The screws have a patented drill and drive thread for reduced splitting of the timber, reduced 'jacking' and spinning of joined timber, increased pull-out and a firmer fix. A sharp point provides faster bite and is capable of piercing 0.8mm steel. The screws have an 'Elementech 400' coating providing an anti-corrosive metal finish, which lasts up to 6 times longer than standard zinc coatings. The coating is environmentally friendly and does not contain Cr6+. It is Salt Spray tested to 400 hours. The screws are suitable for interior use. Every tub is supplied with a Torx® compatible bit.Size: 5.0 x 60mm.Pack quantity: 500.
Forgefix TechFast Timber to Steel CSK/Wing Screws are used to join timber to steel frame buildings. The screws are fitted with breakaway wings that create a clearance hole to protect thread from engaging timber when drilling through. Breakaway wings will ream a hole, then break-off when they contact the metal surface to be drilled. The thread will then engage with metal. They have a TORX® compatible insert for a higher transmission of power. With improved countersinking from recessed ribs. Fire and corrosion resistant. Complies with EU Safety, Health and Environmental requirements.These Forgefix TechFast Timber to Steel CSK/Wing Screws have the following specification: Size: 5.5 x 65mmClamping Thickness: 45mmEffective Thread Length: 44mmPack Size: 100Drill Tip: No.3 No.3 drill tip for self-drilling heavy gauge steel up to 5mm.
These Forgefix Phillips, Single Coarse Thread (SCT) Drywall Screws have a black phosphate finish for increased durability. Their Bugle Head allows the screw to sink effortlessly into the dry lining without the need for countersinking, which in turn minimises the damage to the surface. They are supplied collated, with 50 screws per strip and 1,000 screws per box. APPLICATION:Designed for fitting dry lining to studding. Phosphate coatings are made up of thin crystalline layers of phosphate compounds that adhere to the surface of the fixing or fastener. The phosphate crystals are porous and can be formed from zinc, manganese, or iron phosphate solutions. Phosphate coatings offer good corrosion resistance and have an excellent ability to absorb supplementary coatings which improves appearance, corrosion resistance and resistance to abrasion. The Phillips screw has four simple tapered slots. It is designed so that a Phillips tip screwdriver can turn a screw with increasing torque. When the torque gets to be too strong for the tip then the screwdriver tip winds itself out of the screw thus preventing over-tightening and or damage to the screw head. Coarse thread screws (mainly drywall screws) have an extremely sharp point and are designed to penetrate plasterboard skin. The coarse thread eases in to the board then the timber baton holding the board firm.Drywall Collated Screw Phillips Bugle Head SCT 3.9 x 55mm Box 1000
These Forgefix Phillips, Single Coarse Thread (SCT) Drywall Screws have a black phosphate finish for increased durability. Their Bugle Head allows the screw to sink effortlessly into the dry lining without the need for countersinking, which in turn minimises the damage to the surface. They are supplied collated, with 50 screws per strip and 1,000 screws per box. APPLICATION:Designed for fitting dry lining to studding. Phosphate coatings are made up of thin crystalline layers of phosphate compounds that adhere to the surface of the fixing or fastener. The phosphate crystals are porous and can be formed from zinc, manganese, or iron phosphate solutions. Phosphate coatings offer good corrosion resistance and have an excellent ability to absorb supplementary coatings which improves appearance, corrosion resistance and resistance to abrasion. The Phillips screw has four simple tapered slots. It is designed so that a Phillips tip screwdriver can turn a screw with increasing torque. When the torque gets to be too strong for the tip then the screwdriver tip winds itself out of the screw thus preventing over-tightening and or damage to the screw head. Coarse thread screws (mainly drywall screws) have an extremely sharp point and are designed to penetrate plasterboard skin. The coarse thread eases in to the board then the timber baton holding the board firm.Drywall Collated Screw Phillips Bugle Head SCT 3.9 x 45mm Box 1000
Forgefix TechFast Roofing Sheets to Steel Hex Screws are used for joining metal roofing panels to steel frame buildings. The screws are fire resistant and corrosion resistant. Protected by Elementech corrosion resistant coating, salt spray tested to 1000 hours. Complies with EU Safety, Health and Environmental requirements. They are supplied with 16mm EPDM rubber washers.These Forgefix TechFast Roofing Sheets to Steel Hex Screws have the following specification: Size: 5.5 x 65mmEffective Thread Length: 42mmPack Size: 100Drill Tip: No.5 No.5 drill tip for self-drilling in heavy gauge steel up to 12.5mm.
These ForgeFix ForgeFast Wood Screws have a universally accepted, Pozi compatible drive. They have 6 underhead lobes for improved countersinking and reduced surface dust, and reinforced countersunk necks which improve holding power. The screws have an anti-friction thread for reduced splitting of the timber, reduced 'jacking' and spinning of joined timber and improved drawing strength. The thread is serrated for improved pull-out and reduced torque when inserting the screw. The double cutting point allows faster drilling time and reduced clogging of wood dust and is capable of piercing 0.8mm steel. The screws have a 'Elementech 400' coating providing an anti-corrosive metal finish, which lasts up to 6 times longer than standard zinc coatings. The coating is environmentally friendly and does not contain Cr6+. It is Salt Spray tested to 400 hours. The screws are suitable for interior use.Size: 3.0 x 30mm.Box quantity: 200.
Forgefix TechFast Roofing Sheets to Steel Hex Screws are used for joining metal roofing panels to steel frame buildings. The screws are fire resistant and corrosion resistant. Protected by Elementech corrosion resistant coating, salt spray tested to 1000 hours. Complies with EU Safety, Health and Environmental requirements. They are supplied with 16mm EPDM rubber washers.These Forgefix TechFast Roofing Sheets to Steel Hex Screws have the following specification: Size: 5.5 x 25mmEffective Thread Length: 8mmPack Size: 100Drill Tip: No.3 No.3 drill tip for self-drilling in heavy gauge steel up to 5mm.
