Faithfull heavy-Duty keyed chuck for use on both Rotary and Impact drills. Fitted with an anti-thrust bearing to increase the amount of grip and to prevent slipping when under load. Designed in accordance to DIN 6349The FAICHUCK12 comes complete with key and adaptor for use with SDS and SDS Plus machines.When used with SDS machines, the drill MUST NOT be used in hammer mode1/2in x 20 UNF thread. Capacity 13mmComplete with chuck key.
The Faithfull range of open drum cable reels come in a choice of 25m or 50m cable lengths (1.5mm diameter cable) plus a 25m heavy-duty (2.5mm diameter cable) version for larger site applications - all of which are fitted with thermal overload protection and are manufactured to British Standard BS EN 61242 All reels feature a sturdy steel frame construction with carry handle for easy movement around the worksite. They are fitted with 2 outlet sockets to run 1 or more power tools etc, the sockets are protected with spring loaded flaps to keep unwanted debris out when not in use and a winding knob for easy and tangle free reel-in. NOTE: All cable reels should be fully unwound before they are used to carry their recommended maximum load.110VFully Unwound 1760W (16 amp)Fully Wound 660W (6 amp)Twin sockets and 25m of cable with fitted plug1.5mm cable diameter
Trend Craft Pro Two Fluted Tungsten Carbide Tipped straight cutters are suitable for a wide range of applications such as engraving, grooving, rebating and shallow morticing. They can be used on a wide range of materials such as softwoods, hardwoods, MDF, plywood and chipboard. All cutters are TCT and have a bottom cut feature. When deep cuts are required, more than one pass should be taken. Shank: 1/4inSuitable for a wide range of applications such as engraving, grooving, rebating and shallow morticing. Use on softwoods, hardwoods, MDF, plywood and chipboard. All cutters have a bottom cut feature. D1 1/2 inch D1 12.7 mm Cut length 2 inches Cut length 50 mm Shank Diameter 1/2 inch
This two wing slotting cutter is ideal for grooving and rebating operations. A 1/2in diameter bearing is supplied with every cutter. Depth of cut can be changed by purchasing alternative bearing sizes. T.C.T.Shank = 1/4in.C = 6.3 mm (Slots) Depth with standard cutter = 3/8in.
The Trend Craft Pro Round Over Cutter is used for edge detailing on curved and straight work with additional bearing for quirked, Ovolo detail option. Its 9.5mm radius will cut a full bullnose profile for detailing work on 19mm stock. 1/4in shank for easy control in smaller routers with 'K' mark shank to ensure safe working practices. Specially designed PTFE coated bodies to minimise heat and resin build-up and Micro-granular Tungsten Carbide tips ensure a premium finish in hard and soft woods, and abrasive man-made boards such as ply, MDF and chipboard, to meet the needs of the woodworker and tradesman for quality and performance.
Trend CO76X1 Rounding over, self-guiding TCT cutter for rounding over edges do not require a side fence with a 6.3 mm radius x 12.7 mm cut. Supplied with two bearings - use the larger bearing for a round-over. If the cutter is lowered, a top quirk can be produced. Bullnose mouldings can also be produced by taking a second pass from the opposite side of the workpiece.
Trend Craft Pro Two Fluted Tungsten Carbide Tipped straight cutters are suitable for a wide range of applications such as engraving, grooving, rebating and shallow morticing. They can be used on a wide range of materials such as softwoods, hardwoods, MDF, plywood and chipboard. All cutters are TCT and have a bottom cut feature. When deep cuts are required, more than one pass should be taken. Shank: 1/4inD - Diameter - 3/8in 9.5mmC - Cutting Length - 3/4in 19.1mmT.C.T. 2 Flutes.
Trend Craft Pro Two Fluted Tungsten Carbide Tipped straight cutters are suitable for a wide range of applications such as engraving, grooving, rebating and shallow morticing. They can be used on a wide range of materials such as softwoods, hardwoods, MDF, plywood and chipboard. All cutters are TCT and have a bottom cut feature. When deep cuts are required, more than one pass should be taken. Shank: 1/4inD - Diameter - 5/32in 4.0mmC - Cutting Length - 7/16in 11.1mmT.C.T. 2 Flutes.
The Starrett BU310-5 Wood Cutting Jigsaw Blades with Unified Shank™, will fit in virtually all jigsaw machines. These blades feature 170% more weld contact area than standard bi metal blades through the Unique™ solid state diffusion bonding process. This ensures exceptionally strong teeth, combined with the multiple cutting edges and split chip advantage, ensure that these blades typically last 25% longer than directly competing products. Supplied as a pack of 5. Specification Length: 75mm.Width: 7.5mm.Thickness: 1.3mm.TPI: 10.Tooth: Ground.Set: Tapered. Length dimension references tooth bearing section of the blades, the total length including shank is approximately 25mm longer.
Biscuit jointing has proven to be one of the strongest, fastest, safest and most accurate ways to join hard and soft woods, plywood, composition boards etc.Compared to dowelling, biscuit joinery is faster and more precise.The biscuits are made of laminated beech which is then compressed before being die cut.Beechwood biscuits expand up to 20 per cent when in contact with a woodworking adhesive. (e.g. PVA Glue).Trend BSC/10/1000 Biscuits Size: No.10 (53 x 19 x 4mm).Pack Size: 1000.
Designed for high volume operation, coils contain large quantities of nails meaning that reloading down time can be kept to a minimum. You will find them in the pallet and crate, fencing, garden furniture and the construction industries. All Coil Nails are Round Head nails. Typically: Coils of nails with diameters from 2.0 mm to 2.2 mm contain 350 nails. Coils of nails with diameters from 2.5 mm to 3.1 mm. Contain 225 nails. Roofing nail coils contain 120 nails, due to the extra large diameter of the head. 15° Collation angle Ring shank nails have a series of rings punched into the surface of the shank. A difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising, or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails. For use with: N57C-1CE heavy-duty Coil Nailer N58C-1-E Coil Nailer N58C-1-E Coil Nailer N66C-2-E Coil NailerFinish: Bright.Size: 2.1 x 40mm.Box quantity: 24,500.
These Faithfull Professional 1/4in Hexagon Drive Phillips Screwdriver Bits are manufactured from high strength, heat treated ‘S2’ grade steel. Bits are shock and wear resistant and feature precision machined tips to provide an optimum fit, helping to prevent screw stripping and cam-out and provide a long working life.These Faithfull S2 Grade Steel Screwdriver Bits have the following specification: Size: PH2 x 25mm.Pack Size: 3.
Faithfull Professional 1/4in Hexagon Drive Impact Screwdriver Bits are specifically designed and for use in high torque impact drivers. Manufactured from a unique material specially engineered for extreme durability these bits have an increased working life compared to standard screwdriver bits. Impact bits are designed to distribute impacts evenly, preventing energy waste for efficient screw driving and incorporate torsion areas to absorb torque peaks and to reduce stress at the bit tip during heavy loading. All bits feature a precision machined tip to provide an optimum fit helping to prevent screw stripping and cam-out.These Faithfull Impact Screwdriver Bits have the following specification: Size: PH2 x 50mm.Pack Size: 3.
These Faithfull Professional 1/4in Hexagon Drive Phillips Screwdriver Bits are manufactured from high strength, heat treated ‘S2’ grade steel. Bits are shock and wear resistant and feature precision machined tips to provide an optimum fit, helping to prevent screw stripping and cam-out and provide a long working life.These Faithfull S2 Grade Steel Screwdriver Bits have the following specification: Size: PH2 x 50mm.Pack Size: 3.
These Faithfull Professional 1/4in Hexagon Drive Phillips Screwdriver Bits are manufactured from high strength, heat treated ‘S2’ grade steel. Bits are shock and wear resistant and feature precision machined tips to provide an optimum fit, helping to prevent screw stripping and cam-out and provide a long working life.These Faithfull S2 Grade Steel Screwdriver Bits have the following specification: Size: PH1 x 25mm.Pack Size: 3.
The Trend PH/JIG Pocket Hole Jig is great for fast and accurate joining of timber and plywood, giving strong instant joints. Solid hardened bushes with variable pitch of 29mm to 63mm. Use on timber, MDF, plywood and block board. Allows a variety of joints to be created individually. Uses square drive self tapping screws. Work piece can be handled immediately after gluing and screwing, creating time saving benefits. No clamps required.The Trend PH/JIG Pocket Hole Jig is supplied with: 100 x Dome Head Screws, 1 x Face Clamp, 1 x HSS Drill Bit With Collar, 1 x 75mm Square Drive Bit, 1 x 150mm Square Drive Bit.
Trend solid carbide planer blades fit portable electric planers and are supplied in pairs.They have two cutting edges and are reversible, giving extended life.Planer blades must be securely clamped so they cannot work loose during use.For use with:DEWALT - DW676K.Elu - MFF40, MFF80K, MFF80, MFF81, MF81K, MFF81EK.
The Faithfull T shank Jigsaw Blade Set is the ideal companion for any jigsaw, this 10 piece set contains 6 alternative types of blades for a wide variety of woodcutting applications. 2 x FAI T144D HCS Fast straight cutting2 x FAI T101D HCS Clean straight cutting2 x FAI T101B HCS Clean straight cutting2 x FAI T111C HCS Fast straight cutting1 x FAI T119BO HCS Curved cutting1 x FAI T101AO HCS Curved cutting anti-splinter N.B. FAIT101AO is not available as a single item.
The Lessmann Cup Brushes are filled with crimped wire and are ideal for working on large surfaces. They can also be used for the removal of rust, paint, dirt or scale and for polishing. A range of sizes and wire styles are available.Diameter.80mm.Wire Height. 22mm.Bore. M14.Wire Gauge. 0.35.Wire Type. Steel.Max. R.P.M. 8,500.
The Lessmann Cup Brushes are filled with crimped wire and are ideal for working on large surfaces. They can also be used for the removal of rust, paint, dirt or scale and for polishing. A range of sizes and wire styles are available.Diameter. 80mm.Wire Height. 22mm.Bore. M14.Wire Gauge. 0.30.Wire Type. Stainless.Max. R.P.M. 8,500.
The Lessmann Cup Brushes are filled with crimped wire and are ideal for working on large surfaces. They can also be used for the removal of rust, paint, dirt or scale and for polishing. A range of sizes and wire styles are available.Diameter. 75mm.Wire Height. 25mm.Bore. M10.Wire Gauge. 0.25.Wire Type. Steel.Max. R.P.M. 12,000.
