The quick release drill system for drilling, countersinking and screwing designed for use with Power Drills and Screwdrivers and is compatible with direct-drive 1/4in Hex Shank Power Bits.Drill Size.2.4mm.(3/32in)Countersink Size. No.6.
BT13 Series 18 gauge brown Brad nails for use with the Bostitch brad nailer. Finish nails (Brads) are normally of a rectangular cross section instead of being round. Their diameters are less than the coil and stick nails, and are primarily used for finish and trim work in the construction and joinery industries.Length : 30mm.Colour : Brown.Pack : Clam pack of 1000.
Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments. 28° Collation Angle Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out. (Remember only tools fitted with sequential trip should be used when working up a ladder). Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them. Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.Gauge/Diameter (mm) 3.1 Length 90 28 Collation AngleSKU S310R90G8 Profile RING Finish G8 Description STICK NAIL 3.10-90 RING GAL8 2M Qty per box 2000 Will also fit the N80SB, FW28WW-E, N100S
The DEWALT Series 60 Extreme Circular Saw Blade with laser cut expansion slots that help to reduce vibration and noise. The extra large sub micro grain carbide teeth remain sharper for much longer and can be resharpened up to 20 times. This stationary circular saw blade range can be used for cutting in natural wood, plywood, laminates, particleboard and MDF. Ideal for both table and mitre saws.The DEWALT DT4332 Series 60 Circular Saw Blade has the following specification: Finish: General Purpose.Blade Diameter: 315mm.Bore Size: 30mm.Tooth Count: 48.Plate Thickness: 2.2mm.Kerf Thickness: 3.0mm.Grind: ATB.Rake Angle: +10°.
The DEWALT Torsion Phillips Bits with a hardened core for extra strength and durability. They have a flexible torsion zone that absorbs torque peaks and reduces breakage. The design inculdes etra grip ribs that grip the screw and reduce slipping (specific bits only). These are tough quality, professional screwdriver bits.DEWALT DT7232 Torsion Bits PH2 25mm Pack of 5
The DEWALT Torsion Pozi Bits have a hardened core for extra strength and durability. They have a flexible torsion zone absorbs torque peaks and reduces breakage (Torsion bits only). The design features extra grip ribs that grip the screw and reduce slipping (specific bits only). They are tough quality, professional screwdriver bits.DEWALT DT7226 Torsion Bits PZ2 50mm Pack of 5
The DEWALT DT70745T FLEXTORQ™ Screwdriving Set contains a selection of EXTREME® FlexTorq™ screwdriving bits engineered for longer life. The built-in torsion zone has been designed to absorb and control high-impact forces, transferring them into the optimised geometry of the bit tip. Reducing the load on the driver and fastener, means secure fixing with longer life. The full fit head eliminates wobble and screw head rounding. Supplied in a TOUGH CASE+, this is part of a connectable case system that is TSTAK™ compatible. Individual TOUGH CASES can be clipped together for easy transportation. Contains: 1 x 25mm Phillips Bit: PH21 x 25mm Pozi Bit: PZ210 x 25mm TORX Bits: T10, T15(x2), T20(x4), T25(x2) & T302 x 25mm TORX Security Bits: T20 & T25 1 x 57mm Phillips Bit: PH21 x 57mm Pozi Bit: PZ214 x 57mm TORX Bits: T10(x2), T15(x3), T20(x5) & T25(x4) 1 x Magnetic Bit Tip Holder with Torsion Zone
The DEWALT DT70737T FLEXTORQ™ Screwdriving Set contains a selection of EXTREME® FlexTorq™ screwdriving bits engineered for longer life. The built-in torsion zone has been designed to absorb and control high-impact forces, transferring them into the optimised geometry of the bit tip. Reducing the load on the driver and fastener, means secure fixing with longer life. The full fit head eliminates wobble and screw head rounding. Supplied in a TOUGH CASE+, this is part of a connectable case system that is TSTAK™ compatible. Individual TOUGH CASES can be clipped together for easy transportation. Contains: 4 x 25mm Phillips Bits: PH1, PH2(x2) & PH38 x 25mm Pozi Bits: PZ1, PZ2(x6) & PZ32 x 25mm TORX Bits: T20 & T25 4 x 57mm Phillips Bits: PH1 & PH2(x3)9 x 57mm Pozi Bits: PZ1, PZ2(x6) & PZ3(x2)3 x 57mm TORX Bits: T20(x2) & T25 1 x Magnetic Bit Holder with Torsion Zone
The DEWALT EXTREME T Shank Metal Cutting Blades deliver superior surface finish & precision with long cutting life. The blade is 50% stronger reducing blade breakage and wandering with a reinforced tooth design for greater precision and longer blade life. The bi-metal construction provides enhanced flexibility and durability. Supplied in a pack of 3.DEWALT DT2154 EXTREME T Shank Metal Cutting Blades for fast cuts in steel up to 6mm thick. Also for aluminium, copper, brass and other soft metals from 3-6mm thick.
The DEWALT EXTREME T Shank Metal Cutting Blades deliver superior surface finish & precision with long cutting life. The blade is 50% stronger reducing blade breakage and wandering with a reinforced tooth design for greater precision and longer blade life. The bi-metal construction provides enhanced flexibility and durability. Supplied in a pack of 3.DEWALT DT2150 EXTREME T Shank Metal Cutting Blades for fast cuts in steel up to 3mm thick. Also for aluminium, copper, brass and other soft metals to 3mm thick.
The DEWALT DT70738T FLEXTORQ™ Screwdriving Set contains a selection of EXTREME® FlexTorq™ screwdriving bits engineered for longer life. The built-in torsion zone has been designed to absorb and control high-impact forces, transferring them into the optimised geometry of the bit tip. Reducing the load on the driver and fastener, means secure fixing with longer life. The full fit head eliminates wobble and screw head rounding. Supplied in a TOUGH CASE+, this is part of a connectable case system that is TSTAK™ compatible. Individual TOUGH CASES can be clipped together for easy transportation. Contains: 1 x 25mm Phillips Bit: PH11 x 25mm Pozi Bit: PZ210 x 25mm TORX Bits: T10, T15, T20(x4), T25(x3) & T302 x 25mm TORX Security Bits: T20 & T25 1 x 57mm Phillips Bit: PH21 x 57mm Pozi Bit: PZ214 x 57mm TORX Bits: T10(x2), T15(x2), T20(x6) & T25(x4) 1 x Magnetic Bit Holder with Torsion Zone
The DEWALT DT70730T FLEXTORQ™ Screwdriving Set contains a selection of EXTREME® FlexTorq™ screwdriving bits engineered for longer life. The built-in torsion zone has been designed to absorb and control high-impact forces, transferring them into the optimised geometry of the bit tip. Reducing the load on the driver and fastener, means secure fixing with longer life. The full fit head eliminates wobble and screw head rounding. Supplied in a TOUGH CASE+, this is part of a connectable case system that is TSTAK™ compatible. Individual TOUGH CASES can be clipped together for easy transportation. Contains: 1 x 25mm Slotted Bit: 6mm8 x 25mm Pozi Bits: PZ2(x7) & PZ36 x 25mm TORX Bits: T20(x2) & T25(x4) 2 x 57mm Phillips Bits: PH2(x2)3 x 57mm Pozi Bits: PZ2(x2) & PZ3 1 x 89mm Phillips Bit: PH21 x 89mm Pozi Bit: PZ21 x 89mm TORX Bit: T20 1 x Compact Magnetic Drive Guide with Torsion Zone1 x Cleanable Socket Driver: 8mm
The Zenith Satin Mop is suitable for satin finishing work. It gives a satin or brushed finish to all metals.The ZENSFF62W Satin Mop has the following specifications:Grade: Fine.Size: 6 x 2 Lap.
The Masterplug Pro-XT Open Metal Cable Reel is ideal for use with workshop and other outdoor tools. It has a robust design with two UK type sockets and a high visibility cable. The cable reel features a handy cable guide, power LED indicator and a pull out handle. For safety, it features a thermal cut-out switch.
Masterplug 110 Volt low voltage cable reel with thermal cut-out to prevent overheating. With 2 x 16 Amp Sockets and a sturdy tubular steel frame. Available in 25 metre or 50 metre lengths and manufactured to BS EN 61242.25 metre arctic cable.
Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. Two flutes give a clean finish to cut edges. 1/4in Shank.C = 19 mmD = 25.4 mm 1in
These plug cutters are designed to exactly fit the counterbored holes produced by group 62 and 63 Trend cutters. Recommended speed - 1,000-20,000 /min.TC1/4in Shank. Plug Depth Max. 16mmPlug Depth Min. 12mmPlug Body Diameter. 12mm
The Dormer P809 Solid Carbide Bright Rotary Burr with oval ball nose geometry for skip flute grinding and increased strength at the centre. With a reduced chance of swarf congestion and improved cutting action closer to the centre. Produces double cuts, making it a good first choice for general machining. With an improved ease of control, increased metal removal rate and breaks swarf into manageable pieces. They have toughened and hardened steel shanks that provide rigidity and strength. This prevents bending and reduces vibrations for an improved tool life. Ground to h6 (Carbide) and h7 (Steel). Excellent impact strength that is able to withstand high forces and to withstand higher temperature without failing. Special brazing elements provide excellent braze strength.The Dormer Solid Carbide Rotary Bright Burr Oval has the following specification: Diameter: 16mm.Shank Diameter: 6mm.Working Length: 25mm.Overall Length: 70mm.
The Dormer P807 Solid Carbide Bright Rotary Burr with ball nose geometry for skip flute grinding and increased strength at the centre. With a reduced chance of swarf congestion and improved cutting action closer to the centre. Produces double cuts, making it a good first choice for general machining. With a improved ease of control, increased metal removal rate and breaks swarf into manageable pieces. They have toughened and hardened steel shanks that provide rigidity and strength. This prevents bending and reduces vibrations for an improved tool life. Ground to h6 (Carbide) and h7 (Steel). Excellent impact strength that is able to withstand high forces and to withstand higher temperature without failing. Special brazing elements provide excellent braze strength.The Dormer Solid Carbide Bright Rotary Burr Ball has the following specification: Diameter: 9.6mm.Shank Diameter: 6mm.Working Length: 8mm.Overall Length: 54mm.
The Dormer P803 Solid Carbide Bright Rotary Burrs have cylinders with end cuts and produce double cuts. The first choice for general machining, improves ease of control, increased metal removal rate and breaks swarf into manageable pieces. They have toughened and hardened steel shanks that provide rigidity and strength. This prevents bending and reducing vibrations for an improved tool life. Ground to h6 (Carbide) and h7 (Steel). Excellent impact strength that is able to withstand high forces and to withstand higher temperature without failing. Special brazing elements provide excellent braze strength.The Dormer Solid Carbide Bright Rotary Burr - Cylinder With Endcut has the following specification: Diameter: 16mm.Shank Diameter: 6mm.Working Length: 25mm.Overall Length: 70mm.
Biscuit jointing has proven to be one of the strongest, fastest, safest and most accurate ways to join hard and soft woods, plywood, composition boards etc.Compared to dowelling, biscuit joinery is faster and more precise.The biscuits are made of laminated beech which is then compressed before being die cut.Beechwood biscuits expand up to 20 per cent when in contact with a woodworking adhesive. (e.g. PVA Glue).Trend BSC/20/1000 Biscuits Size: No.20 (60 x 23 x 4mm).Pack Size: 1000.
Tooling for use on webbed aluminium and UPVC extrusions by window and door fabricators. Cutters are produced in special high speed steel (HSSE) to ensure a clean cut and resist the abrasive nature of anodised aluminium extrusions. Cutters are designed to plunge and machine or mill lateral slots All tooling for aluminium should be used with a coolant, wax stick, or lubricant. The material being worked on should always be securely clamped in a machine vice. HSSE.One Flute helical Plunge-slotting bit.8 mm Shank.D = 8 mmC = 14 mmOL = 120 mm
The Lessmann Wheel Brushes are filled with crimped wire and are used for obtaining different surface finishes. For the removal of rust, paint and dirt, for roughening, de-burring. Stripping or polishing. A decisive factor for choosing the most suitable brush is the wire and tube diameter. Brushes with a larger tube diameter are filled with more wire, are more aggressive and have a longer life. Some of the brushes are supplied with adaptor sets that allow easy mounting on all popular grinding machines. The adaptors have the following dimensions: Set 1: 30, 22.2, 20, 16 & 12mm, 1in & 1/2in. Set 2: 40, 32, 22.2, 20, & 16mm, 1in & 1/2in.Set 3: 50, 32, 22.2, 20, & 16mm, 1in & 1/2in.Set 4: Brushes With Metal Discs Bore 50.8 & Double Keyway 7x13; Plus Adaptor to Bore 30.Diameter. 125mm.Width. 20-22mm.Min/Max Bore: 13/40mm.Wire Gauge. 0.30/0.35.Wire Type. Steel Crimped.Max R.P.M.6,000
The Lessmann Conical Knot Brushes with left hand twisted knots to increase stability. The special shape of the conical brushes enables the user to work in hard to reach places. They have been designed for heavy-duty use, for the preparing of metal surfaces before painting, and the removal of slag, rust, scale, or concrete waste.Diameter. 100mm.Width. 10mm.Bore. M14.Wire Gauge. 0.50.Wire Type. Steel.Max R.P.M. 12,500
