The Wiha SoftFinish Dowel Racket has a special structure in its interior which provides galvanic separation between the blade and the solid steel cap. This ensures the tool is optimally suited to hammering dowel holes quickly and easily. No drill. No mess. No continuous noise.Galvanic separation between the blade and solid steel cap ensures the user is always protected, even if they accidentally hit a live wire. The optimised profile ensures there is as little splitting as possible when hammering into the wall. A scale on the blade quickly and conveniently shows the user how deep the hole is.Fitted with an ergonomically shaped SoftFinish multi-component handle. Made of special, skin-friendly material and is perfectly sized in your hand. PLEASE NOTE: Not an insulating product as per IEC 60900. Blade non-insulated; must not be touched when used. Safe grip in the rear handle section since striking cap is galvanically separated from blade and protected against discharge. Supplied with: 4 x Dowels: 30mm(x 2) and 40mm(x 2).
Cuts all metals including non ferrous, pipe conduit, stainless and sheet metal. Suitable for use with materials 1.5 to 10mm (1/16 inch to 3/8 inch) thick, dependent on the TPI of the blade. These blades have the following specification:Blade Type: Metal Cutting, 818R, 200mm x 18tpi. The Irwin IRW10504156 Sabre saw 818R metal cutting blades (200mm) comes in a pack of 5 with 18TPI.
The Irwin Construction Circular Saw Blade with expansion slots which dissipate heat and prevent warping. Its construction grade tungsten carbide tips retain their edge, and the plate is fully hardened for durability. The blade features alternate top bevel tooth grind (ATB) for cross cutting and ripping in all woods. Its corrosion resistant coating provides longer quality performance. Suitable for use with handheld corded machines.This IRWIN Construction Circular Saw Blade has the following specification: Blade Diameter: 184mm.Bore: 30mm.Teeth: 40.Kerf Thickness: 2.5mm.Tooth Config: ATB.
These Irwin Wood Jigsaw Blades are made from Carbon steel for use in softer materials such as wood, laminated chipboard, and plastics. They have 3 Sided, fleam ground teeth for fast cut and clean finishes in all wood applications. T Shank for AEG, Bosch, DEWALT and Hitachi Jigsaws. These Irwin 10504224 (T244D) Wood Jigsaw Blades provide very fast clean cuts in hard and soft wood, particleboard 6-60mm.
The ForgeFix ForgeFast Impact Screw Guide with a 1/4in hex shank is made from specially engineered hardened steel to extend wear resistance and bit life. Finish: Black Phosphate
These round Flex sanding papers are ideal for grinding joint filler in drywall construction. When fitted on to a sander, they are ideal for processing large surfaces on walls and ceilings. The sheets are punched to enable dust extraction. They have Hook & Loop backing and are suitable for the following Flex models: GE 5 / GE 5 RGSE 5RWSE 7 Vario SetWSE 7 Vario PlusWST 700VVWST 700VV Plus.The FLX348538 Sanding Papers have the following specifications:Grit size: P100Grit type: FineDiameter: 225mm.Pack size: 25.
Faithfull single point diamond grinding wheel dresser that can be used to accurately shape and clean the cutting face of vitrified bench grinder wheels. When used regularly, this tool will maintain the cutting surface of a grinding wheel, helping to ensure that precision cutting tools are honed and sharpened correctly for optimum performance. The dresser is manufactured from a hardened and tempered polished steel handle and fitted with a diamond tip. Regular truing and dressing of vitrified grinding wheels removes worn abrasives and waste materials that have become embedded into the grinding wheel. This restores the cutting face for optimum performance and helps to minimise vibration. Single point diamond dressing tools are suitable for use on most surface, cylindrical and internal grinding applications.Tip: 0.50 Carat Diamond.Suitable for bench grinding wheels of 150mm to 250 mm diameter.
Flexovit Delta hook & loop sanding sheets; tough and sharp high performance aluminium oxide, combined with a heavy paper backing makes this product extremely durable, long lasting and suitable for use on a variety of surfaces. Fits most brands of Delta sanders, the hook & loop backing allows quick and easy sheet changing and the perforated holes allow free and easy dust extraction. Suitable for use on: wood, paint and metal. Size: Delta Shape, 94mm.Packed in 6s
IRWIN Mixed Screwdriver Bit Set. The insert bits are manufactured from industrial-grade S2 steel for long life and durability. Engineered for use in hand-driving applications or with power tools when used with the IRWIN insert bit holder. Supplied in a compact carry case. Contains: 3 x 25mm Phillips Bits: PH1, PH2, PH3.3 x 25mm Pozidriv Bits: PZ1, PZ2, PZ3.4 x 25mm TORX Bits: TX10, TX15, TX20, TX25.1 x Bit Holder.
Irwin Multi Material Circular Saw Blade with construction grade tungsten carbide tips which retain their edge for longer and can be resharpened. Fully hardened plate with expansion slots help to dissipate heat and prevent warping. With Triple Chip Grind teeth (TCG) for an excellent cutting finish and a corrosion resistant coating for longer quality performance.This IRWIN Multi Material Circular Saw Blade has the following specifications: Blade Diameter: 160mm.Bore: 20mm.Teeth: 48.Kerf Thickness: 2.4mm.Tooth Config: TCG/Neg.
LENOX® Double Tang DIAMOND Reciprocating Saw Blade with a narrow kerf design for thinner, faster cuts. The cutting edge features nickel alloy brazed diamond particles that help to maintain sharpness, so it keeps on cutting long after conventional carbide grit fails. Fitted with a durable chrome alloy backing steel that provides extra stability. LENOX® DIAMOND Blades cut cleanly through cast iron, tile, granite and other abrasives, unlike bulky snap cutters which crush pipes and leave ragged, uneven cuts.1 x LENOX® Double Tang DIAMOND Reciprocating Saw Blade 225mm
Dual action orbital sander pad. Super polyurethane replacement backing pad for random orbital sanders. Medium density, thick profile with unique straight edge lip and a 16mm foam layer. Max RPM=10,000. Made in Great BritainSize : 150 mm (6 Inch)Thread Size : 5/16 UNFGRIP® fixing face6 Hole E80
The Trend Kitchen Worktop Jig is a hard-wearing solid laminate, 12mm thick jig that enables cutting both parts of the joint in 15 minutes including setting up. The jig has the following features: Left and right hand corners, 400mm radius peninsular joint, 45° end cut with slight radius, 45° trade corner, 40mm radius corner, 35mm kitchen door hole and 3/4inch BSP hole for mixer taps. Engraved lines for 65mm bolts and worktop cross-cut. 6 x 10mm diameter ABS plastic pins with tapered shoulders for a tight fit and 3 point pin contact to ensure ease of setting up.Tradesman ALL IN ONE work top jig for up to 900 mm worktops. Hard wearing solid laminate 12 mm thick jig that cuts both parts of the joint in 15-minutes including setting up and left hand and right hand corners, 400 mm radius peninsular joint, 45 degree end cut with slight radius, 45 degree trade corner solution for hob units, 100 mm radius corner, 40 mm radius corner, 35 mm kitchen door hole and 3/4 inch BSP hole for mixer taps. It covers fixed lengths for 400 mm, 500 mm, 550 mm, 600 mm, 616 mm, 650 mm, 700 mm and 900 mm wide worktops and can cuts up to 40 mm thick worktops with or without anti-drip postformed edge. Three open-ended bolt recesses (dog bone style) for 150 mm bolts. Engraved lines for short 65 mm bolts and worktop cross-cut. 10 mm diameter plastic pins with tapered shoulder for tight fit provides three point pin contact to ensure ease of setting up. Engraved markings for identification of pin holes. Specification:Length: 1185 mm. Width: 390 mm. Thickness: 12 mm. Weight: 7.7 Kg. End cut: 45 degrees. Corner radius: 40 mm. Corner radius: 100 mm. Corner radius: 400 mm. Corner mitre joint: 45 degrees.
Replacement bearing to suit all Trend bearing guided router cutters. The Bearings are shielded to prevent penetration of dust and grease packed for life and should not be cleaned with solvent or lubricated as this will dissolve the grease and cause premature bearing failure.Outside Diameter:- 5/8inInside Diameter:- 1/4inThickness:- 11/64in
Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods. T.C.T. Tooling1/2in Shank.T.C.T. Tooling1/2in Shank.C = 50 mmD = 12 mm 15/32 in
Trend C056A TCT Radius Cove Cutter with two flutes and carbide TCT tips for a cleaner cut and fast clearance of waste in all timber and timber-based materials. 9.5mm radius, 12.7mm cut depth for classic decorative mouldings and edge details. 1/2in shank ideal for heavy-duty applications and router table use, with a 'K' marked shank to ensure safe working practices. PTFE coating to minimise heat and resin build-up for increased cutter performance and longevity. Specification: Radius: 9.5mmCutting Depth: 12.7mmShank: 1/2in
