Arctic Hayes Silicone Grease lubricates rubber, plastics and other materials for use on valves, taps and rubber O-rings, making it an ideal plumbers grease. Complies with UK water fittings by-laws. WRAS approved.1 x Arctic Hayes Silicone Grease 500g Tub
Bahco 370-4 Chain Strap Wrench with high strength, positive grip for tightening big tubes without the removal of the chain. Length: 300mm (12in).Capacity: 110mm (4 1/4in).
The Arctic Hayes DT1 Radiator Drain Tray Kit is simple and easy-to-use with step by step detailed instructions included. With universal application for 8, 10, 15 and 22mm pipe work. Helps to avoid unnecessary mess and damage to floors to carpets. Perfect for professional use or DIY. Contains the following: Perfect for professional use or DIY. Contains the following: 1 x Draining Tray4 x Water Diverting Collars4 x Reusable Sealing Straps1 x Water-resistant Barrier Gel (sufficient for 6 - 8 applications)
Monument Radiator Spanners Twin Pack with 1 x 10mm and 1 x 12mm square section radiator spanners. Suitable for vent plugs and bleed screws. They are made from zinc plated steel with a slightly offset handle for ease of use.
Monument Disposable deburring tool. The swivelling blade rotates freely to allow allsorts of deburring operations to be carried out inside tubes, on sheet materials, inside holes etc. Suitable for use on steel, copper, brass, plastics, wood and castings.
The Monument 331E Crutch End Domestic Stopcock Key has been designed for turning on and off hard-to-reach or difficult stopcocks, such as under kitchen units, sinks and stiff to turn outside taps. The design provides increased leverage and is supplied with a removable tommy bar in hexagon shaft. This allows it to connect to a socket and ratchet handle for ease of use in difficult corners.
The Monument 2036T ;Olive Puller is ideal for removing olives from copper piping without damaging the attached pipe. Suitable for 15mm and 22mm copper pipe. This puller simply utilises the compression fitting locking nut to remove the olive from the tube. With all the major parts of the tool turned from brass, this olive puller provides a quick and reliable remedy to removing most olives. Made in Britain.
Monument testing plugs are durable, quality flexible drain plug for the pluging of drains and pipes. This plug is easy to use and are avaliable in 3 and 4-inch versions. These plugs are easy to use just place in the pipe end that is being repaired or replaced and simply turn the wing nut knob, this will depress the rubber cone, this will make it expand to seal pipe or tube end with a water tight seal. Used for blocking off drain pipes. Fitted with removable top caps and rubber rings.Monument Drain Test Plug is suitable for blocking off small pipes such as copper for dry testing prior to commissioning. It cannot be used for air testing purposes by itself. Diameter range: 37-45mm. Maximum allowable back pressure: 60psi (4bar).
The Einhell TE-DA 18/760 Li Solo Drain Cleaner with a durable zinc coated coil and sprial that won't rust. Entering and exiting the pipe is easy thanks to the powered feed and results in a neat and tidy cleaning solution. The direction of rotation can be reversed for clearing even major blockages. For user-friendly cleaning the drum has an inlet, outlet and locking mechanism. An LED illuminates the work area. Its ergonomic design and soft grip result in exceptionally easy handling. Part of the Power X-Change series, powered by Lithium-ion rechargeable batteries with a battery management system for a long-life. This drain cleaner comes as a Bare Unit, NO battery or charger. Specifications: Cable Length: 7.6m.Cable Diameter: 7mm.Min./Max. Pipe Diameter: 16/55mm.Rotation Speed: 560/min.Weight: 3.69kg.
Bahco Pipe Slices are automatic tube cutters that fit directly over the pipe and cuts with a simple twist. They are compact in size, making them ideal for work in confined spaces. With orange painted zinc body.Size 12mm
The Bailey's Lockfast drain, chimney and flue brush, has a plastic stock and polypropylene bristles. For brick chimneys and coal burning applications, and drain cleaning purposes.1 x Bailey Z5692 Lockfast Brush 200mm (8in)
Arctic Hayes Gas Leak Spray is non-flammable and non-corrosive. Use to detect leaks in joints, connections, etc. Safe for use on oxygen pipes. Complies with BS EN 14291:2004.
The Arctic Hayes Work Mat is suitable for both interior and exterior work. Easy to fold and store. The anti-slip mat is waterproof and washable, resistant to oil, water, bleaches, detergents and more. Supplied with a free storage bag.1 x Arctic Hayes Work Mat 1800 x 1500mm
Monument 173 has been especially designed for removing stiff backnuts from awkward placed taps and to make tap installation a more rapid process, this tool is for 1/2-inch. BSP and 3/4-inch. BSP taps. The Monument 170 tool stays in position on the tap tail so can be used with one hand and uses mechanical advantage of the thread of the tap tail to remove stiff nuts. Ideal for 1/2-inch and 3/4-inch BSP 25 mm 27 mm nuts 29 mm ribbed 32 mm nuts. The MON173 is complete with 3/8-inch cordless drill adaptor, 1/2-inch square drive, extension tube and full user instructions. For removing stiff backnuts and rapid tap installation for 1/2-inCH. BSP and 3/4-inch. BSP Taps.Tool stays in position on the tap tail. Uses mechanical advantage of the thread of the tap tail to remove stiff nuts. Monument Stiffnuts Professional Boxed Kit. 1/2-inch. and 3/4-inch. BSP 25 mm 27 mm nuts 29 mm ribbed 32 mm nuts. Complete with 3/8-inch. Cordless drill adaptor, 1/2-inch. Square Drive; Extension tube and full instructions.
The Monument 4507X Grip+ R1 Radiator Thermostatic Radiator Valve Tail Fitting Tool with 16mm internal hex. Fits most radiator valves. Use with MON4537 Shorty Swivel Head Handle or MON345 Pro Adjustable Basin Wrench allowing improved access. Made in Britain.
The Bailey's Universal drain, chimney and flue cleaning brush has a plastic stock and polypropylene bristles. For brick chimneys and coal burning applications, and drain cleaning purposes.1 x Bailey Z5682 Universal Brush 100mm (4in)
Monument Compression Fitting Spanner double ended spanner for tightening and loosening most 15 and 22 mm compression fitting nuts. Size: 15/22 mm.Single pack.
Monument Gas Test Gauge is made from tough plastic. Used both for testing pipework installations with air for leaks before the introduction of gas and for checking and setting correct gas pressures on domestic and commercial appliances. Extruded cover slides off and may be clipped over the base for standing the tool vertically during use. Hanging tab permits vertical hanging from suitable protrusions. Marked in millibars, the scale adjusts for zeroing water level. Plastic U Tube.Monument 257C Gas Test Gauge. Size: 300mm (12 in).Capacity: 30 Millibar.
The Sievert 8707 Cyclone Burner has been designed for brazing and soft soldering. It produces an intensive and effective short flame that reaches around the pipe. For use with the 253501, 253511 and 253547 Powerjet. Diameter: 16mm.
MoTip Pro Leak Detector Spray is used to trace leakages in gas pipes. It has a non-flammable and non-corrosive formula. Leak detector spray can be removed with water and is environmentally friendly. DVGW Certified No. NG/5170BR0105.
Centre locking drain test plugs with steel plates, steel wing nuts and brass blanking caps. Suitable for air or water testing of drains and sewers.Size 450mm (18in)
The Arctic Crack-It Shock Freeze Release Spray releases seized and corroded parts through shock freezing. The freeze action breaks the corrosion seal and allows the penetrant to reach the corroded area, releasing the seized items in 1-2 minutes. Also helps to prevent future corrosion and is completely bio-degradable.
The Arctic Hayes Plumbers Washer Kit contains a selection of rubber and fibre washers of the most popular sizes in a handy storage/carry case. Supplied with 12 pieces of each size: 16.5x6, 24x11, 19.5x5, 15.5x4, 12x4, 32x5, 19x10, 19x11, 24x15, 22x12, 18x15 & 24x20mm.
Monument Glass Fibre Plumbers Mat is an asbestos free, heavy-duty and professional quality mat that provides protection in most soldering and brazing work. The mat resists temperatures up to 600° C, and does not present any of the hazards associated with asbestos materials. Made from glass fibre fabric. Size: 12 x 10in (300 x 250mm).
The Sievert HP Hose Assembly comes supplied complete with a connection nipple. It is suitable for use with Promatic Pro 86 and Pro 88 torch handles.Size 2 metre .
The Bahco Plastic Tube Cutter is made from PA, the body is reinforced with fibreglass and fitted with a comfortable bi-material handle. Suitable for plastic tubes up to 32mm. Specification: Cuts: PVC, PEX, PP, PB and PEMax. Capacity: 32mm
The BlueSpot PVC Tube Cutter is manufactured from aluminium and features a sharp and hardened blade for excellent cutting performance. The tube cutter is ideal for cutting materials such as PVC, PPR, PE and PEX tubing. Specification: Capacity: 0-35mm
Monument pipe cutter wheels are made from high quality, heat treated steels.Suitable for both 268 and 289 pipe slices 15 mm and 22 mm copper tube and MON 240C and MON 303 21 mm and 28 mm. Pack colour. Red. Packs are colour coded according to use.
Monument 15mm and 22mm copper pipe bender is also capable of bending 15mm stainless steel pipe. Tubular steel handles and a die cast formers, it comes supplied with 15mm and 22mm guides.
Monument Tap Reseating Tool 1/2in & 3/4in re-cuts the seats of worn taps or stopcocks without disconnection from the pipework. Parallel bushes for use where the internal thread will not allow the entry of tapered cones. For taps with recessed threads in body, use parallel bush series.Cutters are case hardened, feedscrew allows fine adjustment to the cutter.All parts are interchangeable. Fits 1/2in and 3/4in BS5412 bevelled seats. Complete with 17, 20 mm (11/16 in, 13/16 in) Bevelled Cutters. One double bush.
The Monument 2166M TRV Tail Driver Fitting Socket has been designed to enable fast removal and installation of radiator valve tails and will fit most makes and sizes. The socket can be used with a either a cordless drill chuck or ratchet with 10mm hex socket.
