JG Speedfit cold water service stop end that quickly and easily caps off MDPE pipework at termination points on a temporary or permanent basis. The uniquely designed push-fit fitting incorporates stainless teeth to provide a tight and secure grip on the pipe.
Simply push the JG Speedfit cold water service stop end fully onto the pipe. The connection is demountable, making it easy to work with in the ground when maintaining or altering an existing set-up. Designed, manufactured and assembled in the UK.
Instant push-fit connection
Install and demount in seconds without tools
Stainless steel teeth grab ring provides extra grip on the pipe
Durable material with high impact resistance
Non-toxic and no scale build-up
Resists corrosion and biological growth
Compatible with MDPE pipes only (inserts required)
Suitable for cold water use only
JG Speedfit cold water service stop end that quickly and easily caps off MDPE pipework at termination points on a temporary or permanent basis. The uniquely designed push-fit fitting incorporates stainless teeth to provide a tight and secure grip on the pipe.
Simply push the JG Speedfit cold water service stop end fully onto the pipe. The connection is demountable, making it easy to work with in the ground when maintaining or altering an existing set-up. Designed, manufactured and assembled in the UK.
Instant push-fit connection
Install and demount in seconds without tools
Stainless steel teeth grab ring provides extra grip on the pipe
Durable material with high impact resistance
Non-toxic and no scale build-up
Resists corrosion and biological growth
Compatible with MDPE pipes only (inserts required)
Suitable for cold water use only
JG Speedfit cold water service stop tap MDPE x MDPE instantly shuts of water. Simply push the valve fully onto the pipe. To demount, pull the collet towards the body of the push-fit fitting and pull the pipe to release.
Simply push the JG Speedfit cold water service stop tap MDPE x MDPE fully onto the pipe. The connection is demountable, making it easy to work with in the ground when maintaining or altering an existing set-up. Designed, manufactured and assembled in the UK.
Instant push-fit connection and screw down mains stop valve
Install and demount in seconds without tools
Stainless steel teeth grab ring provides extra grip on the pipe
Durable material with high impact resistance
Non-toxic and no scale build-up
Resists corrosion and biological growth
Compatible with MDPE pipes only (inserts required)
Suitable for cold water use only
JG Speedfit cold water service stop tap MDPE x MDPE instantly shuts of water. Simply push the valve fully onto the pipe. To demount, pull the collet towards the body of the push-fit fitting and pull the pipe to release.
Simply push the JG Speedfit cold water service stop tap MDPE x MDPE fully onto the pipe. The connection is demountable, making it easy to work with in the ground when maintaining or altering an existing set-up. Designed, manufactured and assembled in the UK.
Instant push-fit connection and screw down mains stop valve
Install and demount in seconds without tools
Stainless steel teeth grab ring provides extra grip on the pipe
Durable material with high impact resistance
Non-toxic and no scale build-up
Resists corrosion and biological growth
Compatible with MDPE pipes only (inserts required)
Suitable for cold water use only
JG Speedfit cold water service stop tap MDPE x MDPE instantly shuts of water. Simply push the valve fully onto the pipe. To demount, pull the collet towards the body of the push-fit fitting and pull the pipe to release.
Simply push the JG Speedfit cold water service stop tap MDPE x MDPE fully onto the pipe. The connection is demountable, making it easy to work with in the ground when maintaining or altering an existing set-up. Designed, manufactured and assembled in the UK.
Instant push-fit connection and screw down mains stop valve
Install and demount in seconds without tools
Stainless steel teeth grab ring provides extra grip on the pipe
Durable material with high impact resistance
Non-toxic and no scale build-up
Resists corrosion and biological growth
Compatible with MDPE pipes only (inserts required)
Suitable for cold water use only
JG Speedfit cold water service stop tap MDPE x copper or PEX instantly shuts of water. Simply push the valve fully onto the pipe. To demount, pull the collet towards the body of the push-fit fitting and pull the pipe to release.
Simply push the JG Speedfit cold water service stop tap MDPE x copper or PEX fully onto the pipe. The connection is demountable, making it easy to work with in the ground when maintaining or altering an existing set-up. Designed, manufactured and assembled in the UK.
Instant push-fit connection and screw down mains stop valve
Install and demount in seconds without tools
Stainless steel teeth grab ring provides extra grip on the pipe
Durable material with high impact resistance
Non-toxic and no scale build-up
Resists corrosion and biological growth
Compatible with MDPE pipes only (inserts required)
Suitable for cold water use only
JG Speedfit cold water service stop tap MDPE x copper or PEX instantly shuts of water. Simply push the valve fully onto the pipe. To demount, pull the collet towards the body of the push-fit fitting and pull the pipe to release.
Simply push the JG Speedfit cold water service stop tap MDPE x copper or PEX fully onto the pipe. The connection is demountable, making it easy to work with in the ground when maintaining or altering an existing set-up. Designed, manufactured and assembled in the UK.
Instant push-fit connection and screw down mains stop valve
Install and demount in seconds without tools
Stainless steel teeth grab ring provides extra grip on the pipe
Durable material with high impact resistance
Non-toxic and no scale build-up
Resists corrosion and biological growth
Compatible with MDPE pipes only (inserts required)
Suitable for cold water use only
John Guest bulkhead connector push-fit fitting for the connections of metric microduct pipe in through-wall applications. The blown fibre threaded connectors help eliminate fibre/cable snagging.
Featuring a collet with stainless steel teeth, the push-fit fitting provides a secure connection with a simple and instant push-fit action. It eliminates the need for any tools, making the installation process efficiently straight forward. The O-Ring forms an airtight seal that further enhances the strength of the connection.
In the event of repair or network expansion works, the John Guest bulkhead connector provides superior installation flexibility, as the demountable feature of the solution allows for the system to be reconfigured without damage to the microduct or push-fit fitting. John Guest fittings are manufactured and assembled in the UK.
Hardwearing construction for installation in tough conditions
Includes backnut washers
Coloured body provides added UV protection
Push-fit technology ensures swift tool-free installation
Collet with stainless steel teeth grips and securely locks microduct
O-Ring seal enhances connection integrity
Compatible with microduct pipes
John Guest stem adaptor (BSP thread) adapts a push-fit connection to an imperial threaded connection. Fast and simple to install, John Guest Air and Pneumatics creates an instant connection and airtight seal without the need for tools, hot works or sealing agents. Air piping systems can be set up and installed 50% quicker than traditional methods.
The unique collet locking design firmly and securely holds the pipe in place without deforming the pipe or restricting flow. Fittings are also fully demountable, reducing system downtime during maintenance and making it quick and easy to modify or extend systems.
Designed in tough engineered plastic, fittings are compatible with John Guest nylon, powder coated aluminium or LLDPE tubing, as well as copper, PEXa and other soft metal pipe materials. All John Guest fittings are manufactured and assembled in the UK.
Strong acetal copolymer fitting with nitrile O-Ring
Airtight connection with superior flow characteristics
Instant push-fit connection and demountable without tools
Secure collet cover prevents accidental disconnection
Suitable for air and pneumatics piping systems up to 10 bar
Ideal for air, inert gases and vacuum applications
Food grade fitting suitable for potable liquids
Compatible with soft metal or plastic pipe/tubing
John Guest stem adaptor (BSP thread) adapts a push-fit connection to an imperial threaded connection. Fast and simple to install, John Guest Air and Pneumatics creates an instant connection and airtight seal without the need for tools, hot works or sealing agents. Air piping systems can be set up and installed 50% quicker than traditional methods.
The unique collet locking design firmly and securely holds the pipe in place without deforming the pipe or restricting flow. Fittings are also fully demountable, reducing system downtime during maintenance and making it quick and easy to modify or extend systems.
Designed in tough engineered plastic, fittings are compatible with John Guest nylon, powder coated aluminium or LLDPE tubing, as well as copper, PEXa and other soft metal pipe materials. All John Guest fittings are manufactured and assembled in the UK.
Strong acetal copolymer fitting with nitrile O-Ring
Airtight connection with superior flow characteristics
Instant push-fit connection and demountable without tools
Secure collet cover prevents accidental disconnection
Suitable for air and pneumatics piping systems up to 10 bar
Ideal for air, inert gases and vacuum applications
Food grade fitting suitable for potable liquids
Compatible with soft metal or plastic pipe/tubing
John Guest stem elbow push-fit fitting connects two John Guest push-fit fittings to create a 90° swivel type connection. Fast and simple to install, John Guest Air and Pneumatics creates an instant connection and airtight seal without the need for tools, hot works or sealing agents. Air piping systems can be set up and installed 50% quicker than traditional methods.
The unique collet locking design firmly and securely holds the pipe in place without deforming the pipe or restricting flow. Fittings are also fully demountable, reducing system downtime during maintenance and making it quick and easy to modify or extend systems.
Designed in tough engineered plastic, fittings are compatible with John Guest nylon, powder coated aluminium or LLDPE tubing, as well as copper, PEXa and other soft metal pipe materials. All John Guest fittings are manufactured and assembled in the UK.
Strong acetal copolymer fitting with nitrile O-Ring
Airtight connection with superior flow characteristics
Instant push-fit connection and demountable without tools
Secure collet cover prevents accidental disconnection
Suitable for air and pneumatics piping systems up to 10 bar
Ideal for air, inert gases and vacuum applications
Food grade fitting suitable for potable liquids
Compatible with soft metal or plastic pipe/tubing
John Guest LLDPE (linear low density polyethylene pipe) is suitable for a wide range of temperature and pressures, has broad chemical compatibility and is made from non-contaminating materials. It is compatible with pneumatics applications with a maximum pressure 10 bar @ 20°C. At elevated temperatures (50°C), mineral oil used in some systems will degrade LLDPE tubing. Therefore, LLDPE tubing used in pneumatic circuits should be periodically checked and replaced if necessary.
Chemical Resistance
For use of LLDPE with chemicals or potentially aggressive liquids, please refer to our Technical Service Department. When using cleaning agents or other potentially aggressive liquids, please ensure compatibility with pipe and fittings. LLDPE is not recommended for mineral oils, gases and fuels or high pressure compressed air/pneumatic systems.
Exposure to Ultraviolet Light
If biofilm growth is considered an issue, only black pipe should be installed in areas exposed to any light. Black pipe is also UV stabilised and can be installed where exposed to direct sunlight (UV).
Flexible and robust LLDPE (Linear low density polyethylene) pipe
Suitable for air and pneumatics, cold, and intermittent hot water applications
Broad chemical compatibility
Colour coded for easy identification of service type
FDA and NSF certified
John Guest LLDPE (linear low density polyethylene pipe) is suitable for a wide range of temperature and pressures, has broad chemical compatibility and is made from non-contaminating materials. It is compatible with pneumatics applications with a maximum pressure 10 bar @ 20°C. At elevated temperatures (50°C), mineral oil used in some systems will degrade LLDPE tubing. Therefore, LLDPE tubing used in pneumatic circuits should be periodically checked and replaced if necessary.
Chemical Resistance
For use of LLDPE with chemicals or potentially aggressive liquids, please refer to our Technical Service Department. When using cleaning agents or other potentially aggressive liquids, please ensure compatibility with pipe and fittings. LLDPE is not recommended for mineral oils, gases and fuels or high pressure compressed air/pneumatic systems.
Exposure to Ultraviolet Light
If biofilm growth is considered an issue, only black pipe should be installed in areas exposed to any light. Black pipe is also UV stabilised and can be installed where exposed to direct sunlight (UV).
Flexible and robust LLDPE (Linear low density polyethylene) pipe
Suitable for air and pneumatics, cold, and intermittent hot water applications
Broad chemical compatibility
Colour coded for easy identification of service type
FDA and NSF certified
John Guest straight adaptor (BSP thread) push-fit fitting for the connection of metric pipe to a BSP type thread. Fast and simple to install, John Guest Air and Pneumatics creates an instant connection and airtight seal without the need for tools, hot works or sealing agents. Air piping systems can be set up and installed 50% quicker than traditional methods.
The unique collet locking design firmly and securely holds the pipe in place without deforming the pipe or restricting flow. Fittings are also fully demountable, reducing system downtime during maintenance and making it quick and easy to modify or extend systems.
Designed in tough engineered plastic, fittings are compatible with John Guest nylon, powder coated aluminium or LLDPE tubing, as well as copper, PEXa and other soft metal pipe materials. All John Guest fittings are manufactured and assembled in the UK.
Strong acetal copolymer fitting with nitrile O-Ring
Airtight connection with superior flow characteristics
Instant push-fit connection and demountable without tools
Secure collet cover prevents accidental disconnection
Suitable for air and pneumatics piping systems up to 10 bar
Ideal for air, inert gases and vacuum applications
Food grade fitting suitable for potable liquids
Compatible with soft metal or plastic pipe/tubing
Choose this equal straight coupler to securely connect two pipes of the same size. Part of the JG Speedfit plastic push-fit system, the 15mm connector couldn’t be easier to use – simply push it fully onto the pipe, then twist the plastic nut clockwise to lock it in place.
Up to 40% faster to install than traditional methods, the equal straight connector is also easier to use in tight spaces because there’s no need for hot works and tools. Demounting the connection is simple too – you just unlock the nut by hand, push the collet towards the body of the push-fit fitting and pull the pipe to release.
JG Speedfit products blend push-fit and multi-seal technology for a reliable leak-proof connection. The extensive choice of plastic, brass and chrome fittings, tap connectors, valves and flexi hoses gives you everything you need to complete the job in no time.
By combining these products with plastic push-fit pipe, you can create a truly flexible plumbing and heating system. All products are accredited with the leading testing and approval organisations including WRAS, and are suitable for use with plastic or copper pipe.
• Connects two 15mm pipes quickly and securely
• Install or demount in seconds by hand
• Easier to install in confined spaces – no hot works or tools required
• Suitable for hot and cold water services, central heating systems and combi systems
• Compatible with Speedfit PEX and polybutylene plastic pipe (inserts required) and copper pipe
• Minimum operating temperature of 20 °C
• Maximum operating temperature of 105 °C
• Maximum operating pressure at minimum temperature of 12 bar
• Maximum operating pressure at maximum temperature of 3 bar
• BS EN 7291 Parts 1, 2, 3 and S
• WRAS-approved
Technical specification
Brand JG Speedfit
Colour White
Material Plastic
Manufacturer ID PEM0415W
Warranty (years) 50
Diameter (mm) 15
Pack Size 1
Fitting Type Coupler
Equal or Reducing Equal
Choose this equal straight coupler to securely connect two pipes of the same size. Part of the JG Speedfit plastic push-fit system, the 15mm connector couldn’t be easier to use – simply push it fully onto the pipe, then twist the plastic nut clockwise to lock it in place.
Up to 40% faster to install than traditional methods, the equal straight connector is also easier to use in tight spaces because there’s no need for hot works and tools. Demounting the connection is simple too – you just unlock the nut by hand, push the collet towards the body of the push-fit fitting and pull the pipe to release.
JG Speedfit products blend push-fit and multi-seal technology for a reliable leak-proof connection. The extensive choice of plastic, brass and chrome fittings, tap connectors, valves and flexi hoses gives you everything you need to complete the job in no time.
By combining these products with plastic push-fit pipe, you can create a truly flexible plumbing and heating system. All products are accredited with the leading testing and approval organisations including WRAS, and are suitable for use with plastic or copper pipe.
• Connects two 15mm pipes quickly and securely
• Install or demount in seconds by hand
• Easier to install in confined spaces – no hot works or tools required
• Suitable for hot and cold water services, central heating systems and combi systems
• Compatible with Speedfit PEX and polybutylene plastic pipe (inserts required) and copper pipe
• Minimum operating temperature of 20 °C
• Maximum operating temperature of 105 °C
• Maximum operating pressure at minimum temperature of 12 bar
• Maximum operating pressure at maximum temperature of 3 bar
• BS EN 7291 Parts 1, 2, 3 and S
• WRAS-approved
Technical specification
Brand JG Speedfit
Colour White
Material Plastic
Manufacturer ID PEM0415W
Warranty (years) 50
Diameter (mm) 15
Pack Size 2
Fitting Type Coupler
Equal or Reducing Equal
Choose this equal straight coupler to securely connect two pipes of the same size. Part of the JG Speedfit plastic push-fit system, the 22mm connector couldn’t be easier to use – simply push it fully onto the pipe, then twist the plastic nut clockwise to lock it in place.
Up to 40% faster to install than traditional methods, the equal straight connector is also easier to use in tight spaces because there’s no need for hot works and tools. Demounting the connection is simple too – you just unlock the nut by hand, push the collet towards the body of the push-fit fitting and pull the pipe to release.
JG Speedfit products blend push-fit and multi-seal technology for a reliable leak-proof connection. The extensive choice of plastic, brass and chrome fittings, tap connectors, valves and flexi hoses gives you everything you need to complete the job in no time.
By combining these products with plastic push-fit pipe, you can create a truly flexible plumbing and heating system. All products are accredited with the leading testing and approval organisations including WRAS, and are suitable for use with plastic or copper pipe.
• Connects two 22mm pipes quickly and securely
• Install or demount in seconds by hand
• Easier to install in confined spaces – no hot works or tools required
• Suitable for hot and cold water services, central heating systems and combi systems
• Compatible with Speedfit PEX and polybutylene plastic pipe (inserts required) and copper pipe
• Minimum operating temperature of 20 °C
• Maximum operating temperature of 105 °C
• Maximum operating pressure at minimum temperature of 12 bar
• Maximum operating pressure at maximum temperature of 3 bar
• BS EN 7291 Parts 1, 2, 3 and S
• WRAS-approved
Technical specification
Brand JG Speedfit
Colour White
Material Plastic
Manufacturer ID PEM0422W
Warranty (years) 50
Diameter (mm) 22
Pack Size 1
Fitting Type Coupler
Equal or Reducing Equal
John Guest Speedfit products blend push-fit and multi-seal technology for a reliable leak-proof connection. Simple to install and no tools are required when installing or demounting fittings, making it easy to manoeuvre in tight spaces or readjust joins.
Speedfit’s extensive choice of plastic, brass and chrome fittings, tap connectors, valves and flexi hoses gives you everything you need to complete the job in no time. By combining these products with plastic push-fit pipe, you can create a truly flexible plumbing and heating system.
All products are accredited with the leading testing and approval organisations including WRAS and are suitable for use with plastic or copper pipe.
Push-fit plastic fitting for the connection of plastic and copper pipe.
Simply push the fitting fully onto the pipe and twist the plastic nut clockwise to lock in place.
Should the need arise to demount the connection unlock the nut and push the collet towards the body of the fitting and pull the pipe to release.
The fitting ensures an easier working environment in confined places and removes the need for hot works on site.
• Suitable for hot and cold water services, central heating systems and combi systems
• BS EN 7291 parts 1, 2, 3 and S, WRAS approved
• Secure and easy demounting without the need for a tool
• 50 year guarantee
• Minimum operating temperature - 20 °C
• Maximum operating temperature - 105 °C
• Maximum operating pressure at minimum temperature - 12 BAR
• Maximum operating pressure at maximum temperature - 3 BAR
Technical specification
Brand JG Speedfit
Colour White
Material Plastic
Manufacturer ID PEM201510W
Warranty (years) 50
Diameter (mm) 15
Pack Size 1
Fitting Type Coupler
Equal or Reducing Reducing
A Size 15mm
B Size 10mm
John Guest Speedfit products blend push-fit and multi-seal technology for a reliable leak-proof connection. Simple to install and no tools are required when installing or demounting fittings, making it easy to manoeuvre in tight spaces or readjust joins.
Speedfit’s extensive choice of plastic, brass and chrome fittings, tap connectors, valves and flexi hoses gives you everything you need to complete the job in no time. By combining these products with plastic push-fit pipe, you can create a truly flexible plumbing and heating system.
All products are accredited with the leading testing and approval organisations including WRAS and are suitable for use with plastic or copper pipe.
The reducer push-fit plastic fitting for the connection of plastic and copper pipe.
Simply push the fitting fully onto the pipe and twist the plastic nut clockwise to lock in place. Should the need arise to demount the connection unlock the nut and push the collet towards the body of the fitting and pull the pipe to release.
The reducer fitting ensures an easier working environment in confined places and removes the need for hot works on site.
• Suitable for hot and cold water services, central heating systems and combi systems
• BS EN 7291 parts 1, 2, 3 and S, WRAS approved
• Secure and easy demounting without the need for a tool
• 50 year manufacturers guarantee
• Minimum operating temperature - 20 °C
• Maximum operating temperature - 105 °C
• Maximum operating pressure at minimum temperature - 12 BAR
• Maximum operating pressure at maximum temperature - 3 BAR
Technical specification
Brand JG Speedfit
Colour White
Material Plastic
Manufacturer ID PEM062215W
Warranty (years) 50
Diameter (mm) 22
Pack Size 1
Fitting Type Coupler
Equal or Reducing Reducing
A Size 22mm
B Size 15mm
Connect equally-sized pipes to form a 90° pipe bend quickly and securely with this JG Speedfit 15mm elbow. It can be installed in seconds, and no tools are needed – simply push it fully onto the pipe and twist the plastic nut clockwise to lock in place. This Twist & Lock mechanism secures the fitting and adds compression too.
At up to 40% faster to install than traditional methods, JG Speedfit equal elbow push-fit fittings are much easier to use in confined spaces as there’s no need for hot works or tools. Demounting the connection is equally easy. Just unlock the nut by hand and push the collet towards the body of the fitting, then pull the pipe to release.
JG Speedfit blends push-fit and multi-seal technology for a reliable leak-proof connection. Suitable for use with plastic or copper pipe, you can create a truly flexible plumbing and heating system, and complete the job in no time.
• Push-fit system is easy to use for faster installation times
• Provides a secure and reliable leak-proof connection
• Install or demount in seconds, without the need for tools
• Suitable for hot and cold water services
• Can be used on central heating systems and combi systems
• Minimum operating temperature of 20°C
• Maximum operating temperature of 105°C
• 12 bar maximum operating pressure at minimum temperature
• 3 bar maximum operating pressure at maximum temperature
• 50-year guarantee
• Manufactured to BS EN 7291 Parts 1, 2, 3 and S
• WRAS-approved
• Compatible with Speedfit PEX and polybutylene plastic pipe (inserts required) and copper pipe
Technical specification
Brand JG Speedfit
Colour White
Material Plastic
Manufacturer ID PEM01315W
Warranty (years) 50
Angle (°) 90
Diameter (mm) 15
Pack Size 2
Fitting Type Elbow
Equal or Reducing Equal
Connect equally-sized pipes to form a 90° pipe bend quickly and securely with this JG Speedfit 15mm elbow. It can be installed in seconds, and no tools are needed – simply push it fully onto the pipe and twist the plastic nut clockwise to lock in place. This Twist & Lock mechanism secures the fitting and adds compression too.
At up to 40% faster to install than traditional methods, JG Speedfit equal elbow push-fit fittings are much easier to use in confined spaces as there’s no need for hot works or tools. Demounting the connection is equally easy. Just unlock the nut by hand and push the collet towards the body of the fitting, then pull the pipe to release.
JG Speedfit blends push-fit and multi-seal technology for a reliable leak-proof connection. Suitable for use with plastic or copper pipe, you can create a truly flexible plumbing and heating system, and complete the job in no time.
• Push-fit system is easy to use for faster installation times
• Provides a secure and reliable leak-proof connection
• Install or demount in seconds, without the need for tools
• Suitable for hot and cold water services
• Can be used on central heating systems and combi systems
• Minimum operating temperature of 20°C
• Maximum operating temperature of 105°C
• 12 bar maximum operating pressure at minimum temperature
• 3 bar maximum operating pressure at maximum temperature
• 50-year guarantee
• Manufactured to BS EN 7291 Parts 1, 2, 3 and S
• WRAS-approved
• Compatible with Speedfit PEX and polybutylene plastic pipe (inserts required) and copper pipe
Technical specification
Brand JG Speedfit
Colour White
Material Plastic
Manufacturer ID PEM01315W
Warranty (years) 50
Angle (°) 90
Diameter (mm) 15
Pack Size 1
Fitting Type Elbow
Equal or Reducing Equal
John Guest Speedfit products blend push-fit and multi-seal technology for a reliable leak-proof connection. Simple to install and no tools are required when installing or demounting fittings, making it easy to manoeuvre in tight spaces or readjust joins.
Speedfit’s extensive choice of plastic, brass and chrome fittings, tap connectors, valves and flexi hoses gives you everything you need to complete the job in no time. By combining these products with plastic push-fit pipe, you can create a truly flexible plumbing and heating system.
All products are accredited with the leading testing and approval organisations including WRAS and are suitable for use with plastic or copper pipe.
Push-fit plastic fitting for the connection of plastic and copper pipe.
Simply push the fitting fully onto the pipe and twist the plastic nut clockwise to lock in place.
Should the need arise to demount the connection unlock the nut and push the collet towards the body of the fitting and pull the pipe to release.
The fitting ensures an easier working environment in confined places and removes the need for hot works on site.
• Suitable for hot and cold water services, central heating systems and combi systems
• BS EN 7291 parts 1, 2, 3 and S, WRAS approved
• Secure and easy demounting without the need for a tool
• 50 year guarantee
• Minimum operating temperature - 20 °C
• Maximum operating temperature - 105 °C
• Maximum operating pressure at minimum temperature - 12 BAR
• Maximum operating pressure at maximum temperature - 3 BAR
Technical specification
Brand JG Speedfit
Colour White
Material Plastic
Manufacturer ID PEM222222W
Warranty (years) 50
Angle (°) 90
Diameter (mm) 22
Pack Size 1
Fitting Type Elbow
Equal or Reducing Equal
Need to securely connect three pipes of the same size? If you’re using the JG Speedfit push-fit system, you’ll need these equal tee connectors – they can be used with plastic or copper pipes, and it's a far faster way of connecting than using traditional methods.
Installation is simple – you just push the push-fit fitting fully onto the pipe and twist the plastic nut clockwise to lock in place. No tools are needed, which makes it far easier to manoeuvre in tight spaces or to readjust joins. Tool-free dismounting is equally straightforward, by unlocking the nut and pushing the collet towards the body of the fitting. Then, you just need to pull the pipe to release it.
• Install or demount in seconds, without the need for tools
• Suitable for hot and cold water services
• Can be used on central heating systems and combi systems
• Minimum operating temperature of 20°C
• Maximum operating temperature of 105°C
• 12 bar maximum operating pressure at minimum temperature
• 3 bar maximum operating pressure at maximum temperature
• 50-year manufacturer’s guarantee (T&Cs apply)
• Manufactured to BS EN 7291 Parts 1, 2, 3 and S
• WRAS-approved
• Compatible with Speedfit PEX and polybutylene plastic pipe (inserts required) and copper pipe
Technical specification
Brand JG Speedfit
Colour White
Material Plastic
Manufacturer ID PEM0215W
Warranty (years) 50
Diameter (mm) 15
Pack Size 1
Fitting Type Tee
Equal or Reducing Equal
Need to securely connect three pipes of the same size? If you’re using the JG Speedfit push-fit system, you’ll need these equal tee connectors – they can be used with plastic or copper pipes, and it's a far faster way of connecting than using traditional methods.
Installation is simple – you just push the push-fit fitting fully onto the pipe and twist the plastic nut clockwise to lock in place. No tools are needed, which makes it far easier to manoeuvre in tight spaces or to readjust joins. Tool-free dismounting is equally straightforward, by unlocking the nut and pushing the collet towards the body of the fitting. Then, you just need to pull the pipe to release it.
• Install or demount in seconds, without the need for tools
• Suitable for hot and cold water services
• Can be used on central heating systems and combi systems
• Minimum operating temperature of 20°C
• Maximum operating temperature of 105°C
• 12 bar maximum operating pressure at minimum temperature
• 3 bar maximum operating pressure at maximum temperature
• 50-year manufacturer’s guarantee (T&Cs apply)
• Manufactured to BS EN 7291 Parts 1, 2, 3 and S
• WRAS-approved
• Compatible with Speedfit PEX and polybutylene plastic pipe (inserts required) and copper pipe
Technical specification
Brand JG Speedfit
Colour White
Material Plastic
Manufacturer ID PEM0215W
Warranty (years) 50
Diameter (mm) 15
Pack Size 2
Fitting Type Tee
Equal or Reducing Equal
