JG Speedfit bulkhead elbow push-fit fitting that is primarily used for the modular bathroom ‘Pod’ market. The bulkhead allows connections to fixtures, through partitions. Simply push the push-fit fitting fully onto plastic or copper pipe. To demount the connection, push the collet towards the body of the push-fit fitting and pull the pipe to release.
The JG Speedfit bulkhead elbow push-fit fitting is quicker and easier to install in confined spaces than traditional methods as it eliminates the need for hot works or tools. Designed, manufactured and assembled in the UK.
Instant push-fit connection
Install and demount in seconds without tools
Safe flame-free installation, with no hot works, glue or flux
Grip & Seal collet with stainless steel teeth and main O-Ring seal
Non-toxic, resists corrosion and no scale build-up
Compatible with Speedfit PEX and polybutylene plastic pipe (inserts required) and copper pipe
Suitable for cold water use only
JG Speedfit thread washer is for use with female couplers or tap connectors. Designed, manufactured and assembled in the UK
Replacement thread seal for Speedfit tap connectors and FBSP fittings
Suitable for cold and hot water and central heating
JG Underfloor control unit is used to provide heating to a conservatory or room extension up to 30m². It is suitable for use when the boiler serving the existing heating system has the capacity to take the extra output from 2KW to 3KW and the maximum area to be heated is 30m2 or less.
The unit is pre-assembled and pre-wired to allow for a fast and simple installation. It can be plugged into any convenient electrical socket or spur. It also has integral ball valves for isolation from the primary heating system, an adjustable blending valve and a six-metre head circulation pump.
It should ideally be connected to the main central heating flow and returns distribution system, but it can connect to the nearest radiator supply pipe. In this case, the pump will not operate independently and will only obtain hot water when the radiator system is on.
Pre-wired and pre-assembled for a fast a simple installation
Single zone control unit for conservatories and extensions
JG Speedfit push-fit connections
Plug directly into an electrical socket or spur
Integral ball valves for isolation from the primary heating system
Adjustable blending valve and 6m head circulation pump
Anti-vibration mounting bracket
Suitable for underfloor heating applications up to 30m2
JG Underfloor Thermomix Control Pack mixes and controls water temperature for underfloor heating systems (UFH) up to 14kW. The nickel plated unit features a mixing valve, Grundfos A rated pump, return elbow, manifold adaptor and necessary seals.
It also connects directly to the manifold without the need for extra brackets and can be mounted either side of the manifold to suit the application. The unit can also be used to isolate UFH system components for maintenance purposes.
Integral mixing valve, Grundfos A rated pump, return elbow, manifold adaptor and seals
Lightweight and nickel plated design
Automatically adjust pump speed to suit heat load (3 speed settings)
JG Speedfit push-fit connections allow for horizontal or vertical pipe runs
Suitable for use with JG Speedfit PEX and polybutylene barrier pipe (inserts required) and copper pipe
Mountable either side of the manifold
Suitable for JG Underfloor manifolds only
JG Underfloor 4 Port Manifold connects and centralises underfloor (UFH) pipework in one place and distributes warm water through the pipe circuits to provide even and comfortable heat. When combined with the JG Aura wiring centre and JG Aura heating controls, it also offers independent zone control.
Made from stainless steel, the manifold is manufactured to the highest standards. Fast and simple to install, it has a pre-fitted wall bracket and vibration isolation mount and uniquely features JG Speedfit connections and an integral air vent and fill valve. It also features pre-assembled flow rate indicators for adjusting flow and isolating pipe circuits.
Protective dust caps are supplied on the return rail, which can be removed when installing circuit actuator valves to open and close the flow of water to each pipe loop.
High performance stainless steel manifold with 4 ports
Easy to fit wall bracket and vibration isolation mount
Fast and simple push-fit connections (JG Speedfit)
Integral air vent, fill valve and adjustable flow meter
Versatile assembly for left or right-hand supply
Protective and removable dust caps
Suitable for use with JG Speedfit PEX and polybutylene barrier pipe (inserts required)
Screw plugs, pipe inserts (STS) and collet clips supplied
Suitable for underfloor heating applications only
JG Underfloor 8 Port Manifold connects and centralises underfloor (UFH) pipework in one place and distributes warm water through the pipe circuits to provide even and comfortable heat. When combined with the JG Aura wiring centre and JG Aura heating controls, it also offers independent zone control.
Made from stainless steel, the manifold is manufactured to the highest standards. Fast and simple to install, it has a pre-fitted wall bracket and vibration isolation mount and uniquely features JG Speedfit connections and an integral air vent and fill valve. It also features pre-assembled flow rate indicators for adjusting flow and isolating pipe circuits.
Protective dust caps are supplied on the return rail, which can be removed when installing circuit actuator valves to open and close the flow of water to each pipe loop.
High performance stainless steel manifold with 8 ports
Easy to fit wall bracket and vibration isolation mount
Fast and simple push-fit connections (JG Speedfit)
Integral air vent, fill valve and adjustable flow meter
Versatile assembly for left or right-hand supply
Protective and removable dust caps
Suitable for use with JG Speedfit PEX and polybutylene barrier pipe (inserts required)
Screw plugs, pipe inserts (STS) and collet clips supplied
Suitable for underfloor heating applications only
JG Underfloor 6 Port Manifold connects and centralises underfloor (UFH) pipework in one place and distributes warm water through the pipe circuits to provide even and comfortable heat. When combined with the JG Aura wiring centre and JG Aura heating controls, it also offers independent zone control.
Made from stainless steel, the manifold is manufactured to the highest standards. Fast and simple to install, it has a pre-fitted wall bracket and vibration isolation mount and uniquely features JG Speedfit connections and an integral air vent and fill valve. It also features pre-assembled flow rate indicators for adjusting flow and isolating pipe circuits.
Protective dust caps are supplied on the return rail, which can be removed when installing circuit actuator valves to open and close the flow of water to each pipe loop.
High performance stainless steel manifold with 6 ports
Easy to fit wall bracket and vibration isolation mount
Fast and simple push-fit connections (JG Speedfit)
Integral air vent, fill valve and adjustable flow meter
Versatile assembly for left or right-hand supply
Protective and removable dust caps
Suitable for use with JG Speedfit PEX and polybutylene barrier pipe (inserts required)
Screw plugs, pipe inserts (STS) and collet clips supplied
Suitable for underfloor heating applications only
JG Underfloor 10 Port Manifold connects and centralises underfloor (UFH) pipework in one place and distributes warm water through the pipe circuits to provide even and comfortable heat. When combined with the JG Aura wiring centre and JG Aura heating controls, it also offers independent zone control.
Made from stainless steel, the manifold is manufactured to the highest standards. Fast and simple to install, it has a pre-fitted wall bracket and vibration isolation mount and uniquely features JG Speedfit connections and an integral air vent and fill valve. It also features pre-assembled flow rate indicators for adjusting flow and isolating pipe circuits.
Protective dust caps are supplied on the return rail, which can be removed when installing circuit actuator valves to open and close the flow of water to each pipe loop.
High performance stainless steel manifold with 10 ports
Easy to fit wall bracket and vibration isolation mount
Fast and simple push-fit connections (JG Speedfit)
Integral air vent, fill valve and adjustable flow meter
Versatile assembly for left or right-hand supply
Protective and removable dust caps
Suitable for use with JG Speedfit PEX and polybutylene barrier pipe (inserts required)
Screw plugs, pipe inserts (STS) and collet clips supplied
Suitable for underfloor heating applications only
JG Underfloor 12 Port Manifold connects and centralises underfloor (UFH) pipework in one place and distributes warm water through the pipe circuits to provide even and comfortable heat. When combined with the JG Aura wiring centre and JG Aura heating controls, it also offers independent zone control.
Made from stainless steel, the manifold is manufactured to the highest standards. Fast and simple to install, it has a pre-fitted wall bracket and vibration isolation mount and uniquely features JG Speedfit connections and an integral air vent and fill valve. It also features pre-assembled flow rate indicators for adjusting flow and isolating pipe circuits.
Protective dust caps are supplied on the return rail, which can be removed when installing circuit actuator valves to open and close the flow of water to each pipe loop.
High performance stainless steel manifold with 12 ports
Easy to fit wall bracket and vibration isolation mount
Fast and simple push-fit connections (JG Speedfit)
Integral air vent, fill valve and adjustable flow meter
Versatile assembly for left or right-hand supply
Protective and removable dust caps
Suitable for use with JG Speedfit PEX and polybutylene barrier pipe (inserts required)
Screw plugs, pipe inserts (STS) and collet clips supplied
Suitable for underfloor heating applications only
JG Underfloor Overfit Board is a low-profile underfloor heating (UFH) pipe fixing system designed for existing floor structures. Ideal for retrofit projects, the pipe fixing system provides low height build up and is suitable for ground and first floor level applications.
15mm pipe is easily installed into a grooved foil-faced panel over an existing subfloor. Maximum pipe circuit length is 100m with a recommended flow temperature of 50-60ºC.
Existing floor pipe fixing system
Lightweight insulated panel with compressive strength
Grooved foil-faced panel with 200mm centres
Low height build up
Medium to low heat output and response (approx. 50-60w/m2)
Ideal for rooms of all sizes and shapes
Suitable for underfloor heating applications only
JG Underfloor Underfit Board is a low-profile underfloor heating (UFH) pipe fixing system designed for existing timber suspended or floating floor structures. Ideal for retrofit projects, the pipe fixing system provides no height build up and is suitable for ground and first floor level applications.
15mm pipe is easily installed into a grooved foil-faced panel over an existing floor, either between battens or under the floor between joists. Maximum pipe circuit length is 100m with a recommended flow temperature of 50-60ºC.
Existing floor pipe fixing system
Lightweight insulated panel
Grooved foil-faced panel with 200mm centres
Low height build up
Medium to low heat output and response (approx. 50-60w/m2)
Ideal for rooms of all sizes and shapes
Suitable for underfloor heating applications only
JG Aura Probe is used to control underfloor heating (UFH) temperature in rooms where moisture could cause an issue e.g. wet rooms or bathrooms. The sensor is ideal for areas where thermostats cannot be directly installed. It can also control floor temperature where overheating would cause damage. A JG Aura Probe box is required and sold separately.
Monitors and controls temperature
Prevents overheating
JG Underfloor 2 Port Manifold connects and centralises underfloor (UFH) pipework in one place and distributes warm water through the pipe circuits to provide even and comfortable heat. When combined with the JG Aura wiring centre and JG Aura heating controls, it also offers independent zone control.
Made from stainless steel, the manifold is manufactured to the highest standards. Fast and simple to install, it has a pre-fitted wall bracket and vibration isolation mount and uniquely features JG Speedfit connections and an integral air vent and fill valve. It also features pre-assembled flow rate indicators for adjusting flow and isolating pipe circuits.
Protective dust caps are supplied on the return rail, which can be removed when installing circuit actuator valves to open and close the flow of water to each pipe loop.
High performance stainless steel manifold with 2 ports
Easy to fit wall bracket and vibration isolation mount
Fast and simple push-fit connections (JG Speedfit)
Integral air vent, fill valve and adjustable flow meter
Versatile assembly for left or right-hand supply
Protective and removable dust caps
Suitable for use with JG Speedfit PEX and polybutylene barrier pipe (inserts required)
Screw plugs, pipe inserts (STS) and collet clips supplied
Suitable for underfloor heating applications only
JG Underfloor 3 Port Manifold connects and centralises underfloor (UFH) pipework in one place and distributes warm water through the pipe circuits to provide even and comfortable heat. When combined with the JG Aura wiring centre and JG Aura heating controls, it also offers independent zone control.
Made from stainless steel, the manifold is manufactured to the highest standards. Fast and simple to install, it has a pre-fitted wall bracket and vibration isolation mount and uniquely features JG Speedfit connections and an integral air vent and fill valve. It also features pre-assembled flow rate indicators for adjusting flow and isolating pipe circuits.
Protective dust caps are supplied on the return rail, which can be removed when installing circuit actuator valves to open and close the flow of water to each pipe loop.
High performance stainless steel manifold with 3 ports
Easy to fit wall bracket and vibration isolation mount
Fast and simple push-fit connections (JG Speedfit)
Integral air vent, fill valve and adjustable flow meter
Versatile assembly for left or right-hand supply
Protective and removable dust caps
Suitable for use with JG Speedfit PEX and polybutylene barrier pipe (inserts required)
Screw plugs, pipe inserts (STS) and collet clips supplied
Suitable for underfloor heating applications only
JG Underfloor manifold ball valve is designed for installation to the flow supply connection to a JG Underfloor heating manifold.
Durable DZR brass with nickel plate finish
Suitable for use with JG Speedfit PEX and polybutylene barrier pipe (inserts required) and copper pipe
Suitable for JG Underfloor heating manifolds manufactured prior to April 2014
JG Underfloor Spreader Plates (From Above) is an underfloor heating (UFH) pipe fixing system designed for use with timber suspended or floating floors, where a low height build up is required.
15mm pipe is installed into single or double grooved aluminium spreader plates that transmit heat evenly across the floor. insulation is placed in the void below the plates to minimise downward heat loss. Ideal for new builds, extensions and renovations, especially first floor levels.
For existing floor structures install between battens and for new floors, fix between existing joists. If the floor can be raised, floors can also be counter-battened to make installation even easier.
Timber floor pipe fixing system
Aluminium heat diffusion plates
Options for traditional or composite joists
Low height build up
Medium heat output and response
Ideal for all room sizes, single or multi room
Suitable for underfloor heating applications only
JG Underfloor manifold ball valve is designed for installation to the return feed connection to a JG Underfloor Heating manifold
Durable DZR brass with nickel plate finish
Suitable for use with JG Speedfit PEX and polybutylene barrier pipe (inserts required) and copper pipe
Suitable for JG Underfloor heating manifolds manufactured prior to April 2014
JG Underfloor Manifold Isolation Valve is a replacement valve for that thermostatically opens the return port for the associated manifold circuit when in use and closes when shutting down.
Installed on the return bar of the manifold, the valve opens as hot water is pumped through the circuit slowly opening as the temperature rises. The valve closes automatically as the system shuts off and cools.
Durable brass
Suitable for JG Underfloor heating manifolds manufactured prior to April 2014
JG Underfloor Heating Air Vent automatically discharges any air that may build up within the underfloor heating (UFH) system to eliminate any cold spots within the floor.
An alternative solution to manual bleed valves, the integral float automatically drops to allow any air to be vented from the top of the valve. The vent is easy to install as it simply screws directly into the JG Underfloor Manifold.
Integral float automatically releases air
Durable DZR brass with a nickel plate finish
Suitable for underfloor heating applications only
JG Underfloor Angle Ball Valve is a service valve that isolates supply to the underfloor heating (UFH) manifold and control pack.
The ball valve connects the main heating flow and return pipe to the mixing valve, while allowing the supply to the control pack to be safely isolated for maintenance purposes. The angle design allows it to be used in both vertical or horizontal pipe arrangements.
Replacement ball valve for a JG Thermomix Control Pack
Durable DZR brass with nickel plate finish
Angle design for vertical or horizontal pipe arrangements
JG Speedfit push-fit connections for fast and simple install
This JG Underfloor Speedfit mixing valve unit is compatible with the brand's Speedfit underfloor hitting systems.
Product features
Compatible with Speedfit underfloor heating systems
Technical specifications
Brand JG Underfloor
Finish Galvanised
Length (M) 0,29
Length (mm) 290
Material Type Ductile Iron
Range speedfit
Range Name Speedfit
Range Type Wet System Underfloor Heating Valves
Weight 815.00000
Hazardous N
Body Material Ductile Iron
Dimensions (L x W x D) 290 x 220 mm
Material Ductile Iron
Supplier Product Code SPUFH1-H
Type Mixing Valve Unit
WEEE Compliant N
Width (mm) 220
JG Underfloor Pipe Staples are used to quickly and securely fix underfloor heating pipework to insulation. Suitable for screed floor applications, this method of pipe fixing is cost-effective and offers high heat output and response.
The pipe staples are barbed to ensure a secure grip and are easy to install when using a JG Underfloor Staple Gun.
Screed pipe fixing system
Barbed staples secure pipe to insulation
Ideal for regular and irregular shaped rooms
Conduit required when pipework runs through adjacent rooms
Suitable for underfloor heating applications only
JG Underfloor Staple Gun is used for securing staples to the pipe and insulation in screed floor applications.
Robust staple gun
Easy repeatable action
Use with JG Underfloor staples (not included)
Suitable for underfloor heating applications only
