Finish nails and brads have heads that are rectangular. They are the same width as the shank, but the breadth of them is greater than the shank, ensuring that their holding power is enhanced. Applications include partition walls, shop and bar fitting, light framing and timber construction and most second fit applications. For use with N62FN-1, N62FNB-E & N62FNK-2 models. Note: This nail will also fit the N60FN and the N59FNK models. Applications - Partition walls, shop and bar fitting, light framing and timber construction and most second fit applications. 25° collation angleType - 15 gauge angled finish nailFinish - GalvanisedLength - 38mmQTY - Box 3655
Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments. 28° Collation Angle Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out. (Remember only tools fitted with sequential trip should be used when working up a ladder). Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them. Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.Gauge/Diameter (mm) 2.8 Length 65 28 Collation AngleSKU S280R65 Profile RING Finish BRIGHT Description STICK NAIL 2.80-65 RING 2M Qty per box 2000Will also fit the N80SB, FW28WW-E, N100S
Finish nails and brads have heads that are rectangular. They are the same width as the shank, but the breadth of them is greater than the shank, ensuring that their holding power is enhanced. Applications include partition walls, shop and bar fitting, light framing and timber construction and most second fit applications. For use with N62FN-1, N62FNB-E & N62FNK-2 models. Note: This nail will also fit the N60FN and the N59FNK models. Applications - Partition walls, shop and bar fitting, light framing and timber construction and most second fit applications. 25° collation angleType - 15 gauge angled finish nail.Finish - Galvanised.Length - 57mm.QTY - Box 3655.
Designed for high volume operation, coils contain large quantities of nails meaning that reloading down time can be kept to a minimum. You will find them in the pallet and crate, fencing, garden furniture and the construction industries. All Coil Nails are Round Head nails. Typically: Coils of nails with diameters from 2.0 mm to 2.2 mm contain 350 nails. Coils of nails with diameters from 2.5 mm to 3.1 mm. Contain 225 nails. Roofing nail coils contain 120 nails, due to the extra large diameter of the head. 15° Collation angle Ring shank nails have a series of rings punched into the surface of the shank. A difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising, or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails. For use with: N57C-1CE heavy-duty Coil Nailer N58C-1-E Coil Nailer N58C-1-E Coil Nailer N66C-2-E Coil NailerFinish: Galvanised.Size: 2.1 x 40mm.Box quantity: 24,500.
Designed for high volume operation, coils contain large quantities of nails meaning that reloading down time can be kept to a minimum. You will find them in the pallet and crate, fencing, garden furniture and the construction industries. All Coil Nails are Round Head nails. Typically: Coils of nails with diameters from 2.0 mm to 2.2 mm contain 350 nails. Coils of nails with diameters from 2.5 mm to 3.1 mm. Contain 225 nails. Roofing nail coils contain 120 nails, due to the extra large diameter of the head. 15° Collation angle Ring shank nails have a series of rings punched into the surface of the shank. A difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising, or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails. For use with: N57C-1CE heavy-duty Coil Nailer N58C-1-E Coil Nailer N58C-1-E Coil Nailer N66C-2-E Coil NailerFinish: Bright.Size: 2.3 x 45mm.Box quantity: 16,500.
Designed for high volume operation, coils contain large quantities of nails meaning that reloading down time can be kept to a minimum. You will find them in the pallet and crate, fencing, garden furniture and the construction industries. All Coil Nails are Round Head nails. Typically: Coils of nails with diameters from 2.0 mm to 2.2 mm contain 350 nails. Coils of nails with diameters from 2.5 mm to 3.1 mm. Contain 225 nails. Roofing nail coils contain 120 nails, due to the extra large diameter of the head. 15° Collation angle Ring shank nails have a series of rings punched into the surface of the shank. A difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising, or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails. For use with: N57C-1CE heavy-duty Coil Nailer N58C-1-E Coil Nailer N58C-1-E Coil Nailer N66C-2-E Coil NailerFinish: Bright.Size: 2.3 x 55mm.Box quantity: 13,200.
Bostitch Stanox staples are also known as 84 series. For use with TU-216-84-E or other tools using 84 gauge.Wire gauge 0.5 mm x 1mm, 12.3 mm crown staple with 8 mm leg length.
Senco DuraSpin® Collated Decking screws with a green Weatherex coating. Square No.2 drive, coarse thread. 50 screws per strip. CE-marked (EN145566). Suitable for both cordless and mains operated machines.Senco DuraSpin® Collated Decking Screws with Weatherex coating. Size: 4.5 x 75mm.
Senco 34° angled collated brad nails with a sharp chisel point, smooth shank, D-head and Galvanised finish.Senco Chisel Smooth Brad Nails Galvanised Size: 15G x 32mm.
Packs of 2000 Round head nails. These plastic collated stick nails traditionally have a full round head, while only giving marginally better holding power to clipped head nails, they are preferred by the construction industry. Collation is angled at 21° to accommodate the overlapping heads. Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them. Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.65 mm Galvanised Ring round head nails. Type : Ring.Head Width : 2.8 mm.Length : 65 mm.Pack : Box of 2000 nails.
Senco DuraSpin® Self-Drill Collated Screws for drywall to light steel applications. Phillips No.2 drive, phosphate zinc finish, fine-thread. 50 screws per strip. CE-marked (EN145566). Suitable for both cordless and mains operated machines.Senco DuraSpin® Collated Screws for Drywall to Light Steel. Size: 3.9 x 35mm.
Senco 34° angled collated brad nails with a sharp chisel point, smooth shank, D-head and Galvanised finish.Senco Chisel Smooth Brad Nails Galvanised Size: 15G x 64mm.
BT Series galvanised 18 gauge Brad fasteners for use with the Bostitch Finish Bradders. Joined with an adhesive coating that holds the brads together. Finish nails (Brads) are normally of a rectangular cross section instead of being round. Their diameters are less than the coil and stick nails, and are primarily used for finish and trim work in the construction and joinery industries.Gauge/Diameter (mm) 18 GA Length 35 SKU BT13350GA Finish GALV Description MINIBRADS 35 GALVA 5M Qty per box 5000
These DEWALT 16 Gauge Galvanised Finish Nails are compatible with most 16Ga straight magazine nailers. Suitable for a wide range of applications. Made from inspected high-quality steel to ensure reliability in performance. Galvanised nails reduce the likelihood of rust or staining. Available in packs of 2500 and 5000.1 x Box of 2500 DEWALT 16 Gauge Galvanised Finish Nails 32mm
High carbon Zinc Dichromate HCFN finish nail 15 gauge. For use with Bostitch concrete block nailer.50mmGauge/Diameter (mm) 15 GA Box 1500High Carbon Zinc Dichromate Suits: SB-HC50FN
BT Series galvanised 18 gauge Brad fasteners for use with the Bostitch Finish Bradders. Joined with an adhesive coating that holds the brads together. Finish nails (Brads) are normally of a rectangular cross section instead of being round. Their diameters are less than the coil and stick nails, and are primarily used for finish and trim work in the construction and joinery industries.Gauge/Diameter (mm) 18 GA Length 45 SKU BT1345GA Finish GALV Description MINIBRADS 45-GALVA 5M Qty per box 5000
High carbon Zinc Dichromate HCFN finish nail 15 gauge. For use with Bostitch concrete block nailer.40mmGauge/Diameter (mm) 15 GA Box 1500High Carbon Zinc Dichromate Suits: SB-HC50FN
Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments. 28° Collation Angle Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out. (Remember only tools fitted with sequential trip should be used when working up a ladder). Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them. Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.Gauge/Diameter (mm) 2.8 Length 75 28 Collation AngleSKU S280R75G8 Profile RING Finish G8 Description STICK NAIL 2.80-75 RING GAL8 2M Qty per box 2000 Will also fit the N80SB, FW28WW-E, N100S
DEWALT 2nd Fix 15 Gauge DA Finish Nails have a smooth shank and are compatible with most 15Ga 34° angled nailers for a wide range of applications. Made from inspected high-quality steel to ensure reliability in performance. Galvanised (G) and Stainless Steel (S/S) options available. Pack Quantity: 1 x Box 40001 x Box of 4000 DEWALT 15 Gauge Galvanised DA Finish Nails 50mm
The DEWALT Galvanised Ring Shank Nails are paper-taped for use with the DEWALT DCN692 Nailer and other popular brand first fix angled nailers. Annular rings for ultimate grip on first fix, framing applications. Galvanised finish for increased durability, suitable for indoor and outdoor use. Paper-taped for easy loading, handling and a cleaner job. Inclination of the nails in the casing is 33-34°.1 x Box of 2,200 DEWALT DNPT28R50 Galvanised 33° Angle Ring Shank Nails 2.8 x 50mm
Senco DuraSpin® Self-Drill Collated Screws for drywall to light steel applications. Phillips No.2 drive, phosphate zinc finish, fine-thread. 50 screws per strip. CE-marked (EN145566). Suitable for both cordless and mains operated machines.Senco DuraSpin® Collated Screws for Drywall to Light Steel. Size: 3.9 x 45mm.
The DEWALT 16 Gauge Galvanised 20° Finish Nails have been designed for use with the DEWALT 16 gauge nailer, ensuring fewer jamming or fitment issues. DEWALT nails are made from inspected high quality steel to ensure reliability in performance. Galvanised nails reduce the likelihood of rust or staining.These DEWALT DNBA1663GZ 16 Gauge 20° Finish Nails have the following specification: Length: 63mm.Type: 20° Angled Nails.Finish: Galvanised.Gauge: 1.6 (16GA).Box Quantity: 2500.
These HiKOKI Second Fix 16 Gauge Straight Electro Galvanised Finish Nails and gas fuel cells are suitable for applications such as fixing skirting boards, architrave, tongue and groove, wood panelling and fencing. Suitable for use with the HiKOKI NT65GS Second Fix Cordless Nailer.1 x Pack of 2,500 HiKOKI Second Fix Straight Nails 40mm1 x Gas Fuel Cell
Designed for high volume operation, coils contain large quantities of nails meaning that reloading down time can be kept to a minimum. You will find them in the pallet and crate, fencing, garden furniture and the construction industries. All Coil Nails are Round Head nails. Typically: Coils of nails with diameters from 2.0 mm to 2.2 mm contain 350 nails. Coils of nails with diameters from 2.5 mm to 3.1 mm. Contain 225 nails. Roofing nail coils contain 120 nails, due to the extra large diameter of the head. 15° Collation angle Ring shank nails have a series of rings punched into the surface of the shank. A difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising, or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails. For use with: N57C-1CE heavy-duty Coil Nailer N58C-1-E Coil Nailer N58C-1-E Coil Nailer N66C-2-E Coil NailerFinish: Bright.Size: 2.1 x 35mm.Pack quantity: 24,500.
The DEWALT 16 Gauge Stainless Steel 20° Finish Nails have been designed for use with the DEWALT 16 gauge nailer, ensuring fewer jamming or fitment issues. Manufactured from high quality stainless steel for a high resistance to rust. DEWALT nails are made from inspected high quality steel to ensure reliability in performance.These DEWALT DNBA1638SZ 16 Gauge 20° Finish Nails have the following specification: Length: 38mm.Type: 20° Angled Nails.Finish: Stainless Steel.Gauge: 1.6 (16GA).Box Quantity: 2500.
BT13 Series 18 gauge brown Brad nails for use with the Bostitch brad nailer. Finish nails (Brads) are normally of a rectangular cross section instead of being round. Their diameters are less than the coil and stick nails, and are primarily used for finish and trim work in the construction and joinery industries.Length : 32mm.Colour : Brown.Pack : Clam pack of 1000.
Finish nails and brads have heads that are rectangular. They are the same width as the shank, but the breadth of them is greater than the shank, ensuring that their holding power is enhanced. Applications include partition walls, shop and bar fitting, light framing and timber construction and most second fit applications. For use with N62FN-1, N62FNB-E & N62FNK-2 models. Note: This nail will also fit the N60FN and the N59FNK models. Applications - Partition walls, shop and bar fitting, light framing and timber construction and most second fit applications. 25° collation angleType - 15 gauge angled finish nail.Finish - Galvanised.Length - 44mm.QTY - Box 3655.
Senco DuraSpin® Collated Decking screws with a green Weatherex coating. Square No.2 drive, coarse thread. 50 screws per strip. CE-marked (EN145566). Suitable for both cordless and mains operated machines.Senco DuraSpin® Collated Decking Screws with Weatherex coating. Size: 4.2 x 50mm.
Senco 34° angled collated brad nails with a sharp chisel point, smooth shank, D-head and Galvanised finish.Senco Chisel Smooth Brad Nails Galvanised Size: 15G x 44mm.
