The Lessmann Brake Caliper Brush, manufactured for the automobile industry and used for the cleaning of clogged lining deposits when changing brake pad linings. The brush is thin with two rows of straight wire filling and is manufactured this way to prevent damage to sensitive brake areas during use. Available in Steel or Brass. Length: 225mm (9in). 182.401: Straight Steel, Gauge: 0.35.182.451: Crimped Brass, Gauge: 0.25.The Lessmann Brake Caliper Brush has the following specification: Type: Steel Straight, Gauge: 0.35.Length: 225mm (9in).
The Lessmann Brake Caliper Brush, manufactured for the automobile industry and used for the cleaning of clogged lining deposits when changing brake pad linings. The brush is thin with two rows of straight wire filling and is manufactured this way to prevent damage to sensitive brake areas during use. Available in Steel or Brass. Length: 225mm (9in). 182.401: Straight Steel, Gauge: 0.35.182.451: Crimped Brass, Gauge: 0.25.The Lessmann Brake Caliper Brush has the following specification: Type: Brass, Gauge: Crimped 0.25.Length: 225mm (9in).
The Lindstrom Supreme Oblique Cutting Nipper produced from high performance tool steel. It has a screw joint that minimises friction and alignment of cutting edges. The edges are precision induction hardened to 58-60 HRC. The handles with return spring and sleeved.Length (A): 109mm (4.29 in). Blade length (B): 9mm (0.35 in). Head width (C): 9mm (0.35 in). Head depth (D): 6mm (0.24 in). Tip width: (F): 1.0mm (0.04 in). Cutting capacity: 0.2-1.25mm. Head type: TaperedCutting edge: Micro-bevel. The tapered head is the smallest of the standard cutting heads available. Not only does it taper on both sides, but also the underside is cut away, allowing the operater to gain access into some difficult areas. The Micro-Bevel cut is designed to meet the requirements of the electronic assembly industry. Leads are ‘pinched’, allowing less altitude and a smaller overall surface area. Because of its design, it has a wide cutting range and variety of uses.
These Lindstrom Diagonal cutting nippers have an oval head. They are produced from high performance ball bearing steel which is black oxidised for increased durability. The numerically controlled machine grinding guarantees edge and angle accuracy and contact, which increases tool reliability and consistency. The edges are precision induction hardened to 63-65 HRC. The handles have a return spring and are sleeved. Ideal for wire harness work, and standard printed circuit board assembly. Oval heads are the most common type of nipper head. It combines strength and durability, can withstand and distribute the impact of cutting and is utilised in a myriad of applications.Lindstrom Diagonal Cutting Size: 110mm.Type: Micro Bevel Nipper.
These Lindstrom Diagonal cutting nippers have an oval head. They are produced from high performance ball bearing steel which is black oxidised for increased durability. The numerically controlled machine grinding guarantees edge and angle accuracy and contact, which increases tool reliability and consistency. The edges are precision induction hardened to 63-65 HRC. The handles have a return spring and are sleeved. Ideal for wire harness work, and standard printed circuit board assembly. Oval heads are the most common type of nipper head. It combines strength and durability, can withstand and distribute the impact of cutting and is utilised in a myriad of applications.Length (A): 110mm (4.3/8 in)Blade length (B): 10mm (0.39 in). Head width (C): 10mm (0.39 in). Head depth (D): 6mm (0.24 in). Tip width: (F): 0.8mm (0.03 in).Cutting Capacity: 0.1-1.25mm. Cutting edge: Flush Bevel. The Flush Bevel cut is designed to meet the requirements of the electronic assembly industry. Leads are ‘pinched’, allowing less altitude and a smaller overall surface area – more than Micro-bevel cuts. The cutters have fine cutting edges that leave a narrow and short taper and small exposed area. They can be used to meet tight specifications for a flush result to a board, component or part.
These Lindstrom Diagonal cutting nippers have an oval head. They are produced from high performance ball bearing steel which is black oxidised for increased durability. The numerically controlled machine grinding guarantees edge and angle accuracy and contact, which increases tool reliability and consistency. The edges are precision induction hardened to 63-65 HRC. The handles have a return spring and are sleeved. Ideal for wire harness work, and standard printed circuit board assembly. Oval heads are the most common type of nipper head. It combines strength and durability, can withstand and distribute the impact of cutting and is utilised in a myriad of applications.Length (A): 125mm (5 in). Blade length (B): 16mm (0.63 in). Head width (C): 16mm (0.63 in). Head depth (D): 8mm (0.31 in). Tip width: (F): 1.6mm (0.06 in). Cutting capacity: 0.4-2.0mm. Cutting edge: Micro-bevel. The Micro-Bevel cut is designed to meet the requirements of the electronic assembly industry. Leads are ‘pinched’, allowing less altitude and a smaller overall surface area. Because of its design, it has a wide cutting range and variety of uses.
The Lufkin Frame Tape has a unique pistol grip compact design with a smooth wind-in mechanism which fits into a tool chest. The steel blade is graduated with both metric and imperial measurements and will not stretch.The Lufkin FT30CME Frame Tape has both metric and imperial measurements. Blade Length: 30m/100ftBlade Width: 13mmAccuracy: EC Class II
The Lufkin Frame Tape has a unique pistol grip compact design with a smooth wind-in mechanism which fits into a tool chest. The steel blade is graduated with both metric and imperial measurements and will not stretch.The Lufkin FT50CME Frame Tape has both metric and imperial measurements. Blade Length: 50m/165ftBlade Width: 13mmAccuracy: EC Class II
Lufkin Folding Measuring Wheel has an accurate measurements up to 9999.9m. The wheel is calibrated to counter and is accurate for estimated measurements. Wheel brake and reset is located on the handle for convenient multiple measurements. Whilst the 160mm wheel diameter guarantees accurate measurements both indoors and out. Includes carry bag. Specification Size: Extend: 1040mm, Folded: 430mm. Weight: 1.1kg.
Lufkin diameter steel tape is graduated in diameter inches on one side permitting direct reading of diameters. The zero falls in same place on each side of blade and has a manual operation, yellow Clad blade. Specification Blade Length: 6ft (72in)Blade Width: 1/4in
The Lufkin Unilok Pocket Tape has a yellow clad abrasion resistant blade with 2 colour, easy to read markings in metric and imperial graduations. With a self-adjusting end hook. It has a lightweight high strength case with removable belt clip and a toggle lock that holds the blade securely at any length. Built-in shock absorber cushions blade return.This Lufkin YU835CME Unilok Pocket Tape has metric and imperial graduations. Blade Length: 5m/16ftBlade Width: 19mmAccuracy: EC Class II
The Lufkin Unilok Pocket Tape has a yellow clad abrasion resistant blade with 2 colour, easy to read markings in metric and imperial graduations. With a self-adjusting end hook. It has a lightweight high strength case with removable belt clip and a toggle lock that holds the blade securely at any length. Built-in shock absorber cushions blade return.This Lufkin YU835CME Unilok Pocket Tape has metric and imperial graduations. Blade Length: 8m/26ftBlade Width: 19mmAccuracy: EC Class II
The Marshalltown Aluminium Plasterer's Hawk is made from heavy gauge hard-rolled aluminium with smooth straight edges, rounded corners and a 95mm (3.3/4in) flange with extended hub that is threaded for the handle. Fitted with a detachable 125mm (5in) DuraSoft® handle. Also supplied with a sponge rubber callous preventer.1 x Marshalltown M1D Aluminium Plasterers Hawk DuraSoft® Handle 325 x 325mm (13 x 13in)
Marshalltown M120D cement edger designed to give a good finish on steps and verges. Blade of polished steel with sturdy steel mountings. Light and easy to handle with comfortable DuraSoft® handle. Size: 200 x 150mm (8 x 6in).Straight Ends with 10mm (3/8in) Radius.
Marshalltown 19 Series Wooden handled Philadelphia pattern brick trowel with the blade being manufactured from a single piece of high-grade steel, tempered and taper ground with a straight post and carefully set handle angle. The handle is securely attached with a polished steel ferrule, straight shouldered Philadelphia pattern blade. These trowels have been re-engineered and are produced on the most modern forging equipment available. The impact area is strong to provide extra endurance, the flexibility produces the unique feel of Marshalltown brick trowels, straight shouldered Philadelphia pattern blade.Blade length 280 x 140mm (11 x 5 1/2 in)Handle type wooden
145 magnesium hand Floats made from very hard, durable and lightweight magnesium (lighter than traditional trowels). The comfortable wooden handle is positioned to give perfect balance and is secured with screws that will not back out. Magnesium floats produce a smoother finish than wood. Size: 400 x 80mm (16 x 3.1/8in).
Marshalltown 19 Series Leather handled Philadelphia pattern brick trowel with the blade being manufactured from a single piece of high grade steel, tempered and taper ground with a straight post and carefully set handle angle. The handle is securely attached with a polished steel ferrule, straight shouldered Philadelphia pattern blade. These trowels have been re-engineered and are produced on the most modern forging equipment available. The impact area is strong to provide extra endurance, the flexibility produces the unique feel of Marshalltown brick trowels, straight shouldered Philadelphia pattern bladeLeather handle Size. 280 x 140mm (11 x 5 1/2 in)
Marshalltown M192 cement edger designed to give a good finish on steps and verges. Stainless steel blade with sturdy mountings. Light and easy to handle with comfortable DuraSoft® handle. Size: 250 x 100mm (10 x 4in).Straight Ends with 10mm (3/8 in) Radius.
Marshalltown 19 Series Plastic handled Philadelphia pattern brick trowel with the blade being manufactured from a single piece of high grade steel, tempered and taper ground with a straight post and carefully set handle angle. The handle is securely attached with a polished steel ferrule, straight shouldered Philadelphia pattern blade. These trowels have been re-engineered and are produced on the most modern forging equipment available. The impact area is strong to provide extra endurance, the flexibility produces the unique feel of Marshalltown brick trowels, straight shouldered Philadelphia pattern blade.Philadelphia Pattern with plastic handle.Size. 280 x 140mm (11 x 5 1/2 in)
Marshalltown 19 Series Plastic handled Philadelphia pattern brick trowel with the blade being manufactured from a single piece of high grade steel, tempered and taper ground with a straight post and carefully set handle angle. The handle is securely attached with a polished steel ferrule, straight shouldered Philadelphia pattern blade. These trowels have been re-engineered and are produced on the most modern forging equipment available. The impact area is strong to provide extra endurance, the flexibility produces the unique feel of Marshalltown brick trowels, straight shouldered Philadelphia pattern blade.Philadelphia Pattern with plastic handle.Size. 290 x 145mm (11 1/2 x 5 3/4 in).
The Marshalltown 20D Hand Sander is lightweight and is fitted with an exclusive one-piece handle clamp that holds paper firmly and makes changing paper easy. It has a bonded foam pad and DuraSoft® handle, and is designed for pre-cut or half sheet standard sandpaper.
The Marshaltown M23D internal dry wall corner trowel is a lightweight internal corner trowel made from one piece of flexible stainless steel with aluminium mounting. Blade set at 103° angle that flexes to form a perfect 90° corner during use. Fitted with a DuraSoft® handle for user comfort. Specification Size: 100 x 125mm (4 x 5in).Weight: 200g.
Marshalltown Brick Trowels are manufactured from a single piece of high grade tool steel. These trowels have been re-engineered and are produced on the most modern forging equipment available. The blades are expertly ground from heel to toe and are London Pattern with a wooden or Durasoft handle and polished steel ferrule. The impact area is strong to provide extra endurance, the flexibility produces the unique feel of Marshalltown brick trowels.London Pattern with wooden handle. Size. 250 x 115mm (10 x 4 1/2 in).
34 Series Wide London pattern brick trowels are one-piece forged from highest carbon steel then heat treated for strength and durability. The handle rise is set for correct hang and balance. The blade is taper ground and polished. The DuraSoft handle incorporates an integral finger guard, provides a soft feel, reduces fatigue and offers excellent durability. Wide London trowels have a rounded heel which places mortar further forward on the blade than the Philadelphia Pattern Trowels.Made in USA.Wooden handle. Size. 267 x 140mm (10 1/2 x 5 1/2 in)
34 Series Wide London pattern brick trowels are one-piece forged from highest carbon steel then heat treated for strength and durability. The handle rise is set for correct hang and balance. The blade is taper ground and polished. The DuraSoft handle incorporates an integral finger guard, provides a soft feel, reduces fatigue and offers excellent durability. Wide London trowels have a rounded heel which places mortar further forward on the blade than the Philadelphia Pattern Trowels.Made in USA.
34 Series Wide London pattern brick trowels are one-piece forged from highest carbon steel then heat treated for strength and durability. The handle rise is set for correct hang and balance. The blade is taper ground and polished. The DuraSoft handle incorporates an integral finger guard, provides a soft feel, reduces fatigue and offers excellent durability. Wide London trowels have a rounded heel which places mortar further forward on the blade than the Philadelphia Pattern Trowels.Made in USA.Wooden handle with polished steel ferrule. Size. 300 x 145mm (12 x 5 3/4 in).
34 Series Wide London pattern brick trowels with plastic handles are forged from a single piece of high carbon steel, then heat treated for strength and durability. Blade is taper ground and polished to give the correct flexibility and feel. Wide London pattern trowels have a rounded heel which places mortar further forward on the blade than the Philadelphia style trowels.Plastic handle. Size. 280 x 145mm (11 x 5 3/4 in).
34 Series Wide London pattern brick trowels with plastic handles are forged from a single piece of high carbon steel, then heat treated for strength and durability. Blade is taper ground and polished to give the correct flexibility and feel. Wide London pattern trowels have a rounded heel which places mortar further forward on the blade than the Philadelphia style trowels.Plastic handle.Size. 300 x 145mm (12 x 5 3/4 in).
The Marshalltown Taping Knives are available with either a blue steel flexible blade or a stainless steel blade. They are fitted with a comfortable DuraSoft® handle, and are primarily used for smoothing jointing tape in drywall applications.The Marshalltown M3508D Taping Knife is made from blued steel. Size: 200 x 75mm (8 x 3in).
The Marshalltown Taping Knives are available with either a blue steel flexible blade or a stainless steel blade. They are fitted with a comfortable DuraSoft® handle, and are primarily used for smoothing jointing tape in drywall applications.The Marshalltown M3508DS Taping Knife has a premium tempered stainless steel blade mounted in a rigid alloy back. The blade is tapered for easier use in tight corners. Ergonomic contoured Durasoft® handle for improved comfort and control.
The Marshalltown Taping Knives are available with either a blue steel flexible blade or a stainless steel blade. They are fitted with a comfortable DuraSoft® handle, and are primarily used for smoothing jointing tape in drywall applications.Marshalltown M3510D Taping Knife is made from blued steel. Size: 250 x 75mm (10 x 3in).
The Marshalltown Taping Knives are available with either a blue steel flexible blade or a stainless steel blade. They are fitted with a comfortable DuraSoft® handle, and are primarily used for smoothing jointing tape in drywall applications.The Marshalltown M3510DS Taping Knife is made from Stainless Steel. Size: 250 x 75mm (10 x 3in)
The Marshalltown Taping Knives are available with either a blue steel flexible blade or a stainless steel blade. They are fitted with a comfortable DuraSoft® handle, and are primarily used for smoothing jointing tape in drywall applications.The Marshalltown M3512D BTaping Knife is made from blued steel. Size: 300 x 75mm (12 x 3in).
The Marshalltown Taping Knives are available with either a blue steel flexible blade or a stainless steel blade. They are fitted with a comfortable DuraSoft® handle, and are primarily used for smoothing jointing tape in drywall applications.Marshalltown M3512DS Taping Knife is made from Stainless Steel. Size: 300 x 75mm (12 x 3in).
The Marshalltown M36D cement edger is designed to produce a radius at the edge of a concrete slab to prevent the edge from chipping. It has a blade of polished steel with sturdy steel mountings. Light and easy-to-use with a comfortable DuraSoft® handle. Size: 150 x 75mm (6 x 3in).Straight Ends with 10mm (3/8in) Radius.
A sponge rubber pad cemented to an aluminium backing, with smooth handle. Ideal for finishing top coat render. No.38: Fine Cell Pad.No.39: Coarse Cell Pad.Fine Cell Pad.Size. 230 x 100mm (9 x 4 in).Thick 19mm (3/4 in).
