Imperial 13in lengths of high carbon bright steel, precision ground to very close tolerances; Above 1 in + - 0.0005in.Below 1 in + - 0.00025in. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 1/8 in
This micrometer has a 63.5mm (2.1/2in) base and 3.2mm (1/8in) diameter measuring rod. Base and rod are hardened, ground and lapped. Furnished with ratchet stop, lock nut and case. Size: 0-75mm.Rods: 3.Graduation: 0.01mm.
Hardened steel punches carefully heat treated for long life. Precisely knurled body with square head which gives a good striking area and prevents the punch from rolling.Size 3mm (1/8 in).Length 100mm (4 in)
Metric 333mm lengths of high carbon bright steel, precision ground to very close tolerances; Above 25mm + - 0.025mm.Below 25mm + - 0.0127mm. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 3mm
The Moore & Wright Firm Joint Outside Calipers are manufactured from polished tool steel and have a large headed nut and screw assembly that provides a firm and rigid friction joint, with no play. The sizes listed are the effective leg length which is measured from the joint assembly. The Firm Joint Outside Calipers are manufactured to BS3123 standards. Note: Firm joint caliper capacities are generally 1/3 greater than the effective leg length.The Moore & Wright 33124 Firm Joint Outside Calipers have the following specification: Size: 600mm (24in).
Metric 333mm lengths of high carbon bright steel, precision ground to very close tolerances; Above 25mm + - 0.025mm.Below 25mm + - 0.0127mm. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 30mm
Metric 333mm lengths of high carbon bright steel, precision ground to very close tolerances; Above 25mm + - 0.025mm.Below 25mm + - 0.0127mm. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 25mm
Metric 333mm lengths of high carbon bright steel, precision ground to very close tolerances; Above 25mm + - 0.025mm.Below 25mm + - 0.0127mm. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 24mm
Extra long pin punch. Hardened and tempered with a knurled grip. The drive pin sections are 90mm (3.1/2in) long and the diameters of the punches are slightly under the sizes listed. Length: 200mm (8in).Size 8mm (5/16 in)
Imperial 13in lengths of high carbon bright steel, precision ground to very close tolerances; Above 1 in + - 0.0005in.Below 1 in + - 0.00025in. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 1/2 in
Imperial 13in lengths of high carbon bright steel, precision ground to very close tolerances; Above 1 in + - 0.0005in.Below 1 in + - 0.00025in. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 1/4 in
Manufactured from heat-treated tool steel, this dual function tool is used firstly to set the rivet up and then to form the head.Size 2.5 x 115mm (3/32 x 4 3/4 in).
A hexagonal bodied Rivet Snap with the working end heat-treated to ensure a long life.This tool is used for the forming of heads on solid rivets.Size 3 X 115mm (1/8 x 4 1/2 in)
Type 117 Centre punches are manufactured from specially selected steel, hardened and properly tempered. They are well proportioned, nicely finished and have a knurled finger grip. The points are ground at the proper angle to give maximum service, and the tips are accurately centered. Length: 100mm (4in).Size 2 x 100mm (5/64 x 4 in)
Type 117 Centre punches are manufactured from specially selected steel, hardened and properly tempered. They are well proportioned, nicely finished and have a knurled finger grip. The points are ground at the proper angle to give maximum service, and the tips are accurately centered. Length: 100mm (4in).Size 1.5 x 75mm (1/16 x 3 in)
Type 117 Centre punches are manufactured from specially selected steel, hardened and properly tempered. They are well proportioned, nicely finished and have a knurled finger grip. The points are ground at the proper angle to give maximum service, and the tips are accurately centered. Length: 100mm (4in).Size 4 x 100mm (5/32 x 4 in)
Metric 333mm lengths of high carbon bright steel, precision ground to very close tolerances; Above 25mm + - 0.025mm.Below 25mm + - 0.0127mm. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 12mm
Metric 333mm lengths of high carbon bright steel, precision ground to very close tolerances; Above 25mm + - 0.025mm.Below 25mm + - 0.0127mm. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 14mm
Designed for maximum strength and rigidity, this clamp is hardened and extremely useful for holding work together in tapping, drilling and various machine setups. The ends of the jaws are rounded to permit clamping under shoulders or in recesses.Capacity: 44mm (1 3/4 in). Throat Depth: 25mm (1 in).
Letter punches are for marking metals and other solid materials. Produced from quality steel, heat treated to give maximum endurance and accuracy of impression. Packed in attractive plastic box.Size. 5mm (3/16 in)Contents A to Z Plus & (and)
Hexagonal bodied parallel pin punches with extra long pins. Used for driving out long retaining pins. The pin should be first started with a hand or taper punch to avoid damage to the point of the pin punch. Pin length: 63mm (2.1/2in).Overall length: 152mm (6in).Size. 5.5mm (7/32 in).
Hexagonal bodied parallel pin punches with extra long pins. Used for driving out long retaining pins. The pin should be first started with a hand or taper punch to avoid damage to the point of the pin punch. Pin length: 63mm (2.1/2in).Overall length: 152mm (6in).Size. 4.8mm (3/16 in).
Hexagonal bodied parallel pin punches with extra long pins. Used for driving out long retaining pins. The pin should be first started with a hand or taper punch to avoid damage to the point of the pin punch. Pin length: 63mm (2.1/2in).Overall length: 152mm (6in).Size. 3.2mm (1/8 in).
A hardened and tempered parallel pin punch, which is used for removing pins in parallel holes. The pin should be first started with a hand or taper punch to avoid damage to the point of the parallel punch.Size 1.6mm (1/16 in).
