Number punches are for marking metals and other solid materials. Produced from quality steel, heat treated to give maximum endurance and accuracy of impression. Set contains 0-9 with the latter inverted to double up as a 6. Packed in attractive plastic box.Size. 12mm (1/2 in).
This Teng Tools 1/2inch drive Stud Extractor which is ideal for inserting and extracting stud bolts. It has one eccentric journalled, knurled wheel which grips against an internal fluting. The TEN2300 Stud Extractor is suitable for stud sizes, ranging from 5.5m to 19mm (7/32 inch - 3/4 inch).
The Moore & Wright 100 Series Vernier Calipers have a standard workshop model design. They are made of hardened alloyed stainless steel and have a chromed scale with engraved graduations. The calipers allow 4-way measurement and the measuring surface is micro-lapped. The calipers are manufactured to DIN 862 standards. Supplied in a plastic box.The MAW10030BI calipers have the following specifications: Range: 0-300mm (0-12in).Resolution: 0.02mm (0.001in).
These Dormer Metric Coarse Combination Drill & Spiral Flute Taps allow drilling/threading holes in one single operation. They are made from High Speed Steel and are suitable for use on most materials. They can be used in reversible, variable speed power tools. Manufactured to ISO Standards.Size: M6Tip Diameter: 5.0mmOverall Length: 84mm
Faithfull Letter and number punches are used for hand marking metals and other hard materials. They are useful for stamping personal identification or post codes on tools, cycles etc., as frequently recommended by police and insurers. The letter or number sizes as shown, relate to the height of the characters. The punches are manufactured from high quality tested carbon steel with double induction hardened heads to ensure high quality impressions. The body is hardened and the head is tempered to prevent chipping when hammered.Contents : 1, 2, 3, 4, 5, 6, 7, 8, 9, 0 (9 is achieved by reversing 6).Set supplied in plastic box.Size : 5mm (3/16 in).
Metric 333mm lengths of high carbon bright steel, precision ground to very close tolerances; Above 25mm + - 0.025mm.Below 25mm + - 0.0127mm. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 16mm
Metric 333mm lengths of high carbon bright steel, precision ground to very close tolerances; Above 25mm + - 0.025mm.Below 25mm + - 0.0127mm. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 18mm
Metric 333mm lengths of high carbon bright steel, precision ground to very close tolerances; Above 25mm + - 0.025mm.Below 25mm + - 0.0127mm. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 5mm
Metric 333mm lengths of high carbon bright steel, precision ground to very close tolerances; Above 25mm + - 0.025mm.Below 25mm + - 0.0127mm. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 20mm
Metric 333mm lengths of high carbon bright steel, precision ground to very close tolerances; Above 25mm + - 0.025mm.Below 25mm + - 0.0127mm. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 13mm
Metric 333mm lengths of high carbon bright steel, precision ground to very close tolerances; Above 25mm + - 0.025mm.Below 25mm + - 0.0127mm. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 15mm
Metric 333mm lengths of high carbon bright steel, precision ground to very close tolerances; Above 25mm + - 0.025mm.Below 25mm + - 0.0127mm. Closely controlled analysis for uniform machining properties and consistent response to heat treatment. Chamfered, deburred ends for safety.Size 24mm
These Faithfull punches are made from uniformly heat treated carbon steel and are used for removing pins in parallel holes. The removal of the pins should first be started with a hand or taper punch to avoid damage to the end of the parallel punch.Tip Diameter: 2.5mm (3/32in).Length: 100mm (4in).
The Moore & Wright Spring Dividers are manufactured from polished tool steel and the points are hardened to over 550Hv. The bow spring ensures uniform tension over working range and they are fitted with a centrally mounted adjustment screw. These Spring Dividers comply with BS3123 standards. Note: The nominal size is the distance between the centre of the roller and the working ends of the legs.The Moore & Wright 503 Spring Dividers have the following specifications: Size: 75mm (3in).
The Moore & Wright 100 Series Vernier Calipers have a standard workshop model design. They are made of hardened alloyed stainless steel and have a chromed scale with engraved graduations. The calipers allow 4-way measurement and the measuring surface is micro-lapped. The calipers are manufactured to DIN 862 standards. Supplied in a plastic box.The MAW10020BI calipers have the following specifications: Range: 0-200mm (0-8in).Resolution: 0.02mm (0.001in).
The RIDGID Inner-Outer Reamers have a hardened steel construction and are suitable for cutting copper and stainless steel tubing. They have 46 cutting edges on the interior cone that allow for fast, clean, inner reaming and outer deburring/bevelling of 1⁄4in (6mm) to 2in (50mm). The reamers have dual inch/metric measurement bars.RIDGID 227S Inner-Outer Reamer Capacity: 12-54mm (1/2 - 2in).Weight: 0.56kg.
Dormer E500 straight flute taps are the only type of taps that can be used by hand, but they may also be used in a machine if required. Extremely versatile, can tap through or blind holes in most materials. When tapping blind holes straight flute taps should be used in sets. The three taps which form a set are known by more than one name. 1. Taper or First tap2. Second or Intermediate tap3. Bottoming, third or plug tap. Metric coarse straight flute taps. Tolerance: Class 2 for 6H FitSurface treatment: BrightMaterial: HSS High Speed SteelChamfer No: 1,2 and 3, Serial no 4 and 5Flute Geometry: Straight Flutes ISO529Size 5.0mm x 0.8 bottoming
These Dormer 2 piece sets each feature a tap and its corresponding pre-hole drill in one convenient package, helping to save time and error.The packs contain an A002 split-point jobber drill and a straight flute tap. The taps are suitable for threading up to 1.5x their diameter in most materials (ISO Standard). Two tap options are available: Second tap for through drilling, or a bottoming tap for blind holes.Specifications: Tap Type: SecondThread Size: M8
Dormer E500 straight flute taps are the only type of taps that can be used by hand, but they may also be used in a machine if required. Extremely versatile, can tap through or blind holes in most materials. When tapping blind holes straight flute taps should be used in sets. The three taps which form a set are known by more than one name. 1. Taper or First tap2. Second or Intermediate tap3. Bottoming, third or plug tap. Metric coarse straight flute taps. Tolerance: Class 2 for 6H FitSurface treatment: BrightMaterial: HSS High Speed SteelChamfer No: 1,2 and 3, Serial no 4 and 5Flute Geometry: Straight Flutes ISO529Size 16.0mm x 2.0 second
Straight edge for accurate marking out with a carpenters pencil or metal scriber. Accuracy is 0.01% of the length of the straight edge.Size 1200 x 50 x 6mm (48 x 2 x 1/4in).
Straight edge for accurate marking out with a carpenters pencil or metal scriber. Accuracy is 0.01% of the length of the straight edge.Size: 900 x 50mm (36 x 2in).
The Faithfull HSS Straight Flute Taps are versatile, general-purpose taps for threading blind or through-holes in most materials. Suitable for machine cutting, each set contains taper, second and bottom taps to accommodate all threading. The taps are made from high-speed steel, with a bright finish and conform to ISO529.Size: M5Thread: 0.8Drill Size: 4.3mm
Pin vices are chiefly used for holding small taps, reamers, scribers or wire. The handles are tubular which permit holding wires of any length or diameter up through the length of the tool.Size: 1Capacity: 0 - 1mm (0 - 3/64 in)
Q.Max Thrust Races are recommended to increase punch life and to significantly ease the operation of the punch. Makes cutting the holes effortless.This 16mm Thrust Race is suitable for 52-80mm punches.
A quick and easy way to cut clean metric sized holes in sheet metal up to 16 gauge. The special design allows even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches are sold singly without key, which should be ordered separately. Thread the punch onto the hexagonal screw and then pass the hexagonal screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting hexagonal screw until it touches the metal sheet. Use a hexagonal key to turn the hexagonal screw. The screw will pull the punch through the metal and a hole will result. Please note these instructions apply to cutters up to 15 mm in size, for cutters 15 mm and over have a different configuration. Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.Size.52.0mm.Key Type.ME. 14mm hexagonal wrench
A quick and easy way to cut clean metric sized holes in sheet metal up to 16 gauge. The special design allows even load during cutting and produces a burr free hole that needs no extra finishing. Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting. All punches are sold singly without key, which should be ordered separately. Thread the punch onto the hexagonal screw and then pass the hexagonal screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting hexagonal screw until it touches the metal sheet. Use a hexagonal key to turn the hexagonal screw. The screw will pull the punch through the metal and a hole will result. Please note these instructions apply to cutters up to 15 mm in size, for cutters 15 mm and over have a different configuration. Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.Size.20.4mm.Key Type.MB. 8mm hexagonal wrench
Hardened steel punches carefully heat treated for long life. Precisely knurled body with square head which gives a good striking area and prevents the punch from rolling.Size 4mm (5/32 in).Length 100mm (4 in)
SB-3732 series nail punches are manufactured with a plastic handle and fully polished steel surface with a brilliant chrome finish.Tip size: 4.0 mm (5/32in). Length: 125 mm (5in).
The Faithfull Prestige Centre Finder Gauge is manufactured from aluminium using computer numerical controlled (CNC) machines. The black anodised finish offers enhanced corrosion protection and the laser engraved scales give outstanding measurement accuracy. The centre finder is used to find the centre point of a square or cylindrical object. It features ruled markings in millimetre increments and can also be used for 45° and 90° mitre cut lines, making this product ideal for any engineer's workshop.With a measuring capacity of 90mm, this tool can be used on objects with a diameter or width of up to 180mm. Specification: Size: 100mmMeasuring Capacity: 90mm
Feeler gauges are used to adjust tappets, spark plugs, distributor points, check bearing clearances and gear play, fitting pistons, rings and pins and gauging narrow slots. Leaves are tempered steel, easily removed and replaced. There is a locking device on all sets.Millimetre Reading Gauges with Straight leaves 12.7 x 77 mm No. of leaves: 20 Range 0.05 - 1 mm (by 0.05mm steps)
The Starrett Fractional Display Caliper is lightweight, comfortable, and easy to use. Made from hardened stainless steel, it has a slim profile and a clear LCD display, reads 0.01mm, .0005in or 1/64in. The display includes function buttons for zeroing and unit switching (mm, inch, F). A fine adjustment thumb wheel allows for easy measuring and a lock screw to secures the slide position. To save battery life it has an auto-off after 5 minutes. It also features a low battery warning system with flashing display and a USB port for data output. Comes with: a battery cover wrench for easy access and a hardwearing case. Conforms to DIN862 standard. Specifications: Power: Single SR44/LR44 Long-life Battery.Max. Measuring Speed: 1.5m/sec or 60in/sec.1 x Starrett Fractional Display Caliper 200mm.
Recoil inserts are the quick and easy way to repair damaged threads or creating stronger original threads in alloys and composite materials in original equipment manufacture.Made from corrosion resistant stainless steel, they create stronger threads in most materials and simplifiy changeover from unified to metric or vice versa. Recoil thread repair kits contain a quality HSS tap, Installation tool, precision stainless steel inserts and instructions.Supplied in a sturdy container.Supplied with a tapping drill.Kit 5/16 UNC X 18 tpiLength 1 1/2 X Diameter
Recoil Inserts are made from high quality stainless steel wire, with a diamond shaped cross section wound to the shape of a spring thread. The insert, which is larger in diameter than the tapped hole, is compressed during installation then allowed to spring back permanently anchoring the insert in the tapped hole. Because of its larger diameter the recoil insert has a greater contact area and is normally stronger than the original thread.Size M16 x 2.0 Pitch.Length. 1 1/2 x Diameter
Recoil inserts are the quick and easy way to repair damaged threads or create stronger original threads in alloys and composite materials in original equipment manufacture.Made from corrosion resistant stainless steel, they create stronger threads in most materials and simplify changeover from unified to metric or vice versa. Recoil thread repair kits contain a quality HSS tap, installation tool, precision stainless steel inserts and instructions. Supplied in a sturdy container.Supplied with a tapping drill.Kit 7.0mm x 1.0Length 1 1/2 x Diameter
Recoil inserts are the quick and easy way to repair damaged threads or create stronger original threads in alloys and composite materials in original equipment manufacture.Made from corrosion resistant stainless steel, they create stronger threads in most materials and simplify changeover from unified to metric or vice versa. Recoil thread repair kits contain a quality HSS tap, installation tool, precision stainless steel inserts and instructions. Supplied in a sturdy container.Supplied with a tapping drill.Kit 8.0mm x 1.25Length 1 1/2D