The Forgefix Nyloc hexagon nut is a fastener that incorporates a nylon component to effectively lock the nut into position on the bolt. The nylon component has a smaller inside diameter than the actual nut. This locks the nut in place by squeezing the nylon firmly around the bolt when tightened. Unlike a standard locking washer, the Nyloc nut prevents the nut from loosening under vibration as the nylon is tightly wedged into the bolt threads and provides resistance to turning when tightened. The nuts are zinc-plated for increased resistance to corrosion. Their hexagonal shape is designed to be driven by a wrench (spanner) and provides excellent torque when done so. APPLICATION:Where a permanent fastening is required and loosening must be prevented by movement or vibration.Can be used on most bolt products including HT Bolts, Carriage Bolts, Threaded Rod etc. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminum and stainless steels by their oxide layers.Hexagon Nut & Nylon Insert ZP M8 Bag 100
These Forgefix TechFast Hex Head Roofing Screws are designed for fixing cladding and sheet steel to heavy section steel purlins of between 6.0mm and 12.5mm. The screws have a hex head, are self-drilling and have a rubber washer which expands under pressure to form a permanent weather seal. They are zinc plated and have an 'Elementech' coating for superior corrosion resistance, which has been salt spray tested to 1,000 hours.The TFHH5560 TechFast Hex Head Roofing Screws have the following specifications: Size: 5.5 x 60mm.Pack quantity: 50.
These Forgefix Flat Repair Washers have a large 40mm outside diameter. They are bright Zinc Plated for increased corrosion resistance. Washers provide a smooth surface for the nut or bolt to bear on, making it less likely to loosen as a result of an uneven fastening surface. The main purpose of a washer is to distribute the load under a bolt head or the nut face. APPLICATION:On all manner of bolting applications. Can be used with all types of bolts and nuts. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminum and stainless steels by their oxide layers.Flat Repair Washers ZP M10 x 40mm Bag 10
These Forgefix Cable Ties are suitable for a range of tasks in areas including: gardening, electrical installations, sign installation, point of sale applications and much, much more. They can be joined together, increasing the size and diameter reach. The cable tie consists of a tape section with triangular teeth that slope in one direction, as in a ratchet mechanism. The head of the cable tie has a slot with a flexible pawl that rides up the slope of these teeth when the tape is inserted. Once the pointed tip of the cable tie has been pulled through the case and past the ratchet, it is prevented from being pulled back; the resulting loop may only be pulled tighter. Extensive size range from 100-450mm. Available in widths 2.5-8.0mm. The ties have a temperature range for continuous use from 40-85°C.These ForgeFix Cable Ties are: Colour: BlackSize: 3.6 x 150mm Pack Quantity: 100
The ForgeFix Spectre Screws are advanced multipurpose wood screws with double countersunk heads and pozi compatible recess. They have a sawtooth thread design to prevent splitting and reamer to prevent jacking. The screws have a zinc yellow passivated finish for excellent resistance to corrosion. The zinc yellow passivation process of electroplating is similar to the 'galvanised' and 'zinc plated' processes but with the addition of a yellow dye. It offers an aesthetically pleasing finish.Specification: Size: 4.0 x 25mmThread: Fully threadedPack Quantity: Box of 200
These Forgefix Cable Ties are suitable for a range of tasks in areas including: gardening, electrical installations, sign installation, point of sale applications and much, much more. They can be joined together, increasing the size and diameter reach. The cable tie consists of a tape section with triangular teeth that slope in one direction, as in a ratchet mechanism. The head of the cable tie has a slot with a flexible pawl that rides up the slope of these teeth when the tape is inserted. Once the pointed tip of the cable tie has been pulled through the case and past the ratchet, it is prevented from being pulled back; the resulting loop may only be pulled tighter. Extensive size range from 100-450mm. Available in widths 2.5-8.0mm. The ties have a temperature range for continuous use from 40-85°C.These ForgeFix Cable Ties are: Colour: Natural/Clear Size: 4.6 x 200mm Pack Quantity: 100
Faithfull Hose Clips are ideal for fixing flexible rubber hoses, plastic hoses and flexible pipes and can be used around the home, in the garden, workshop or the garage, in most applications where a water or air tight seal is required. The non-perforated worm drive used on these hose clips provides a high thread strength with a smooth running, snag-free winding surface. A hex shaped drive nut allows the use of either a slotted screwdriver, spanner, nutdriver or hose clip driver* when tightening or loosening the clips. Standard range hose clips are manufactured from mild steel and are zinc plated to aid corrosion resistance and are available in a wide variety of sizes. * The Faithfull Flexi-drive hose clip driver (product code: FAISDHOSE) is perfect for fitting and removing hose clips. The driver features a full sized, soft-grip, non-slip handle and a flexible drive shaft that allows easy access when removing or fitting hose clips in difficult to reach or offset positions. Screw head size: 7mm.Size: 1.Adjustment: 25 - 35mm.
The Faithfull Plastic Chain is available in a selection of colours, this range of polythene plastic chain is ideal for both internal and external use. Its alternately contrasting colour sections make it particularly useful when specific areas need to be clearly sectioned off. These plastic chains are supplied in 12.5m reels.The Faithfull FAICHPLW812C plastic chain is white with the following dimensions: Thickness: 8mm
These Faithfull Welded Chains are galvanised for increased durability and protection against the elements. These chains are load tested, but not certified and should never be used for any overhead lifting, load binding or towing applications. Maximum load figures quoted are for guidance ONLY.This Faithfull Galvanised Chain has the following specification: Link Diameter: 6mm.Chain Length: 15m.Max Load: 250kg.
These Forgefix Hook Bolts are Zinc Yellow Passivated for increased durability and corrosion resistance. They have a tough and reliable construction to cover most heavy-duty fixing applications. The four-way expansion shield offers extremely strong and secure anchorage, and the specially manufactured retaining spring ensures encapsulation of the wedge during expansion. APPLICATIONHook bolts are commonly used to attach cables to objects for lifting or holding in place.Ensure the correct spanner is used to ensure accurate installation. The Zinc Yellow Passivation process of electroplating is similar to the ‘Galvanised’ and ‘Zinc Plated’ processes but with the addition of a yellow dye. It provides a coating that is aesthetically pleasing, and which offers excellent resistance to corrosion.Hook Bolt Zinc Yellow Passivated M10 Bag 5
This Energizer® LED Opal GLS Non-Dimmable Bulb has the following specification: Fitting: ES (E27)Input Wattage: 12.5W (60W equivalent)Lumens of Light: 1521 lmSwitching Cycles: 40,000Average Rated Life: 15,000 hoursColour Temperature: 2,700K (Warm White)Lamp Dimensions: 60 x 122mmDimmable: NoRated: A+
These Forgefix General Purpose Pozidrive Screws with Countersunk heads are zinc plated for increased durability. They are an extremely popular general purpose screw, and suitable for use in and with many materials. APPLICATION:Ideal for use in many ironmongery, electrical and plumbing applications.Can be used with various screw cover caps. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminium and stainless steels by their oxide layers. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. The countersunk head is designed to sink flush with substrates to leave a smooth surface finish. They have twin threads, which enable an easy start when driving. Imperial Size > MetricNo.4 = 3.0mm, No.6 = 3.5mm, No.7 = 3.9mmNo.8= 4.0mm, No.10 = 5.0mm, No.12 = 6.0mmGeneral Purpose Pozi Screw Countersunk TT ZP 1.3/4 x 8 Box 200
The Gorilla Heavy-Duty Double Sided Mounting Tape provides a quick and easy solution to mount and repair where traditional fasteners can't. This industrial strength tape grips to smooth and rough surfaces, delivering an instant and weatherproof bond. Suitable for use indoors and outdoors.This Gorilla Heavy-Duty Double Sided Mounting Tape has the following specification: Colour: BlackWidth: 25.4mmLength: 1.52m
The Stanley HT150 Heavy-duty Sharpshooter Hammer Tacker is ideal for furniture fabrication and building insulation. It will accommodate 2 sticks of G-type staples. It has a heavy-duty steel construction and features a full rubber grip which absorb shock and protects hands. Specification: Fires: TRA7 Type G 140 Staples: 6-10mm
Faithfull Hose Clips are ideal for fixing flexible rubber hoses, plastic hoses and flexible pipes and can be used around the home, in the garden, workshop or the garage, in most applications where a water or air tight seal is required. The non-perforated worm drive used on these hose clips provides a high thread strength with a smooth running, snag-free winding surface. A hex shaped drive nut allows the use of either a slotted screwdriver, spanner, nutdriver or hose clip driver* when tightening or loosening the clips. The Stainless range of hose clips are manufactured using a marine grade 316 W5 stainless steel and are ideal where a high resistance to corrosion is required. Clips are available in a variety of sizes. * The Faithfull Flexi-drive hose clip driver (product code: FAISDHOSE) is perfect for fitting and removing hose clips. The driver features a full sized, soft-grip, non-slip handle and a flexible drive shaft that allows easy access when removing or fitting hose clips in difficult to reach or offset positions. Screw head size: 7mm.The Faithfull FAIHC3SSB Stainless Steel Hose Clip comes in the following:Size: 3.Adjustment: 55 - 70mm.
Forgefix Hex Head Lightning Bolts provide a virtually stress-free fixing for close to edge applications. They are self-threading and allow quick and easy installation of most masonry fixing applications. They can simply be screwed into a pre-drilled hole, without the need for a sleeve or plug. The bolts are through-fixing, eliminating the need for marking and re-positioning. They have a high load capacity due to the thread interlocking into the base material. The bolts have an 'Elementech' coating for superior anti-corrosion, which has been salt spray tested to 1,000 hours. Applications: Widely used for fixing battens, balustrades, handrails, racking and holding down machinery, plus many more installation applications. Suitable for most masonry substrates including concrete and brickwork but also for hollow block or bricks due to the nature of the thread type anchoring along the total length of the fixing.Specifications: Size: M12 x 130mm.Pack quantity: 5.
Faithfull Hose Clips are ideal for fixing flexible rubber hoses, plastic hoses and flexible pipes and can be used around the home, in the garden, workshop or the garage, in most applications where a water or air tight seal is required. The non-perforated worm drive used on these hose clips provides a high thread strength with a smooth running, snag-free winding surface. A hex shaped drive nut allows the use of either a slotted screwdriver, spanner, nutdriver or hose clip driver* when tightening or loosening the clips. The Stainless range of hose clips are manufactured using a marine grade 316 W5 stainless steel and are ideal where a high resistance to corrosion is required. Clips are available in a variety of sizes. * The Faithfull Flexi-drive hose clip driver (product code: FAISDHOSE) is perfect for fitting and removing hose clips. The driver features a full sized, soft-grip, non-slip handle and a flexible drive shaft that allows easy access when removing or fitting hose clips in difficult to reach or offset positions. Screw head size: 7mm.Size: O.Adjustment: 16 - 22mm.
These ForgeFix traditional slotted, single thread Wood Screws have countersunk heads and can be used in many internal and external applications. They have a solid brass construction to avoid corrosion. APPLICATION:Used for both decorative and in applications where the screw may come in to contact with the elements avoiding corrosion.Can be used with all manner of wall plugs. Slotted screw driver required. With Slotted screwdrivers it is important to ensure that the tip matches the width of the screw slot, otherwise you run the risk of damaging the screw head. Slotted screwdrivers are available with either Flared or Parallel tips. For the majority of uses the Flared tip is ideal but if the screw needs to be driven below the material surface a Parallel tip screwdriver should be used. Countersunk heads are designed to sink flush with substrates to leave a smooth surface finish. The single threads have been designed to offer higher pull out values and quicker insertion.Wood Screw Slotted Countersunk Solid Brass 1/2 x 8 Box 200
Convenient and economical to use, applied easily by brush, swab or spray, to cold surfaces and then heated to melt the solder and make the joints. Only a thin coat is needed and, as the solder and flux are both applied at once, it saves time. Used in a myriad of industrial jointing applications and a firm favourite with modellers, Fryolux is a uniform mixture of finely powdered tin/lead solder and zinc chloride activated flux. It has a creamy consistency and is reported to be ideal for pre-tinning, solder coating and soft solder assembly.Size: 125g.
These Forgefix high-low thread Concrete Frame Screws are Zinc Yellow Passivated for increased resistance to corrosion. They offer a virtually stress free fixing, allowing close to edge applications. They are through-fixing, eliminating the need for marking and re-positioning when fixing batons etc. The Torx compatible head of the screw enables increased torque control. APPLICATION: Extremely popular fixing for window and door frames. Also now used as a versatile fixing for many applications in DIY, Joinery, Plumbing and Electrical trades. The Zinc Yellow Passivation process of electroplating is similar to the 'Galvanised' and 'Zinc Plated' processes but with the addition of a yellow dye. It offers an aesthetically pleasing finish, whilst having excellent resistance to corrosion. By design, Torx compatible head screws resist cam-out much better than Phillips or Slotted screws. Where Phillips heads were designed to cause the driver to cam out, to prevent over-tightening, Torx compatible heads were designed to prevent it and to achieve a desired torque consistently. Torx compatible head sizes are described using the capital letter 'T', followed by a number. A smaller number corresponds to a smaller point-to-point dimension of the screw head. Only the proper driver can drive a specific head size without risk of ruining the driver or screw. High-Low Thread screws have an excellent holding power in wood due to their alternating high and low thread heights.Concrete Frame Screw Torx High-Low Thread ZYP 7.5 x 132mm Bag 10
These Forgefix Multi-Purpose Pozi Screws with countersunk heads are made from A2 stainless steel. They are ideal for use in and with many materials. APPLICATIONIdeal for use in sanitary locations and in marine environments. Stainless Steel does not corrode, rust or stain with water as ordinary steel does, but despite the name it is not fully stain-proof, most notably under low oxygen, high salinity, or poor circulation environments. Stainless steel is used where both the properties of steel and resistance to corrosion are required. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. The screws' countersunk heads are designed to sink flush with substrates to leave a smooth surface finish. They have single threads, designed to offer higher pull out values and quicker insertion.Multi-Purpose Pozi Screw Countersunk ST Stainless Steel 3.5 x 20mm Box 200
Unibond No More Nails is a high strength grab adhesive that eliminates the need for nails and screws in many DIY and repair jobs. It is safe and easy-to-use, adheres to most building materials and can be used to fill minor gaps on uneven surfaces. No More Nails is ideal for fixing skirting boards, dado rails, architraves, coving, polystyrene mouldings, decorative wall panels, plasterboard, carpet and carpet grippers and worktops.Unibond No More Nails Original Tube 200ml. Supplied in a handy tube.
The ForgeFix Dome Head Rivet has a steel-plated stem and Aluminium head which provides a neat appearance with a low profile. This rivet is the most versatile and commonly specified head style. The dome head has a diameter double that of the rivet body providing more than sufficient bearing surface to retain all but the extremely soft or brittle materials.The rivet assembly is inserted into a hole drilled through the parts to be joined together and can be finally fixed by use of a hand held or pneumatic rivet gun.
Forgefix Hex Head Lightning Bolts provide a virtually stress-free fixing for close to edge applications. They are self-threading and allow quick and easy installation of most masonry fixing applications. They can simply be screwed into a pre-drilled hole, without the need for a sleeve or plug. The bolts are through-fixing, eliminating the need for marking and re-positioning. They have a high load capacity due to the thread interlocking into the base material. The bolts have an 'Elementech' coating for superior anti-corrosion, which has been salt spray tested to 1,000 hours. Applications: Widely used for fixing battens, balustrades, handrails, racking and holding down machinery, plus many more installation applications. Suitable for most masonry substrates including concrete and brickwork but also for hollow block or bricks due to the nature of the thread type anchoring along the total length of the fixing.Specifications: Size: M10 x 130mm.Pack quantity: 10.
These ForgeFix Don Quichotte Medium Gauge Masonry Nails have the following specification: Size: 3.0 x 50mmFinish: Zinc GalvanisedPack Quantity: Box of 100
These Forgefix Veneer Pins are ideal for lightweight and decorative tasks. Their shape helps to reduce splitting in hard or brittle wood. The nails have a 'Bright' finish, which is simply the basic raw mild steel material, without any coating or finish. APPLICATION:General cross section of joinery applications such as fixings decorative timber mouldings.Veneer Pin 20mm Bag Weight 500g
These Forgefix Round Head Nails are multi-purpose nails, for use with both soft and hard timber materials. The nails have a 'Bright' finish, which is simply the basic raw mild steel material, without any coating or finish. APPLICATION:These nails are the most popular type of nail, used in many joinery and construction applications.Round Head Nail Bright Finish 65mm Bag of 2.5kg
These Forgefix Multi-Purpose Pozi Screws with countersunk heads have a zinc yellow passivated finish for increased durability. The screws are immensely popular and versatile, and used in all trades including joinery, electrical and plumbing. Also widely used in DIY applications. APPLICATIONSuitable for use with many materials including PVCu, Timber, Chipboard, MDF, and other similar types. The Zinc Yellow Passivation process of electroplating is similar to the 'Galvanised' and 'Zinc Plated' processes but with the addition of a yellow dye. It offers an aesthetically pleasing finish, whilst having excellent resistance to corrosion. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. The countersunk head is designed to sink flush with substrates to leave a smooth surface finish. They have single threads, designed to offer higher pull out values and quicker insertion.Multi-Purpose Pozi Screw Countersunk ST ZYP 3.0 x 30mm Box 200
These Forgefix Frame Fixings include both plug and screw with Pozi head. The plug is made from Nylon, for a longer life and durability. Its anti-rotation barbs prevent the plug from rotating in the hole. The fixings are through fixing, thus eliminating the need for marking and re-positioning. To use, simply drill through both fixture and into the base material tap in the plug, insert the screw and tighten. APPLICATION:Widely used for batten, window and door frame fixing.Ensure the correct Pozi drive insert bit is used to avoid 'Cam-Out'.Frame Fixing & Plug M8 x 135 Blister 10
Forgefix Hex Head Lightning Bolts provide a virtually stress-free fixing for close to edge applications. They are self-threading and allow quick and easy installation of most masonry fixing applications. They can simply be screwed into a pre-drilled hole, without the need for a sleeve or plug. The bolts are through-fixing, eliminating the need for marking and re-positioning. They have a high load capacity due to the thread interlocking into the base material. The bolts have an 'Elementech' coating for superior anti-corrosion, which has been salt spray tested to 1,000 hours. Applications: Widely used for fixing battens, balustrades, handrails, racking and holding down machinery, plus many more installation applications. Suitable for most masonry substrates including concrete and brickwork but also for hollow block or bricks due to the nature of the thread type anchoring along the total length of the fixing.Specifications: Size: M8 x 75mm.Bag of 10
Forgefix Hex Flange Head Lightning Bolts provide a virtually stress-free fixing for close to edge applications. They are self-threading and allow quick and easy installation of most masonry fixing applications. They can simply be screwed into a pre-drilled hole, without the need for a sleeve or plug. The bolts are through-fixing, eliminating the need for marking and re-positioning. They have a high load capacity due to the thread interlocking into the base material. The flange head acts as a fixed washer, distributing the load under the bolt head. The bolts have an 'Elementech' coating for superior anti-corrosion, which has been salt spray tested to 1,000 hours. Applications: Suitable for most masonry substrates including concrete and brickwork but also for hollow blocks or bricks due to the nature of the thread type anchoring along the total length of the fixing.Specifications: Size: M6 x 75mm.Bag of 10.
Forgefix TechFast Metal Roofing Panels to Timber Hex Screws are used to join metal roofing panels to timber frame buildings. They have a specially designed compression control thread to prevent damage and denting of panels. No pre-drilling is required and the self-drilling T17 Gash Point on screws makes for a rapid installation. The nails are fire and corrosion resistant, protected by Elementech corrosion resistant coating, salt spray tested to 1000 hours. Complies with EU Safety, Health and Environmental requirements. They are supplied with 16mm EPDM rubber washers.These Forgefix TechFast Metal Roofing to Timber Screws have the following specification: Size: 6.3 x 25mmSteel Thickness: 0.5-1.2mmHead Type: 8mm HexPack Size: 100
Forgefix TechFast Roofing Sheets to Steel Hex Screws are used for joining metal roofing panels to steel frame buildings. The screws are fire resistant and corrosion resistant. Protected by Elementech corrosion resistant coating, salt spray tested to 1000 hours. Complies with EU Safety, Health and Environmental requirements. They are supplied with 16mm EPDM rubber washers.These Forgefix TechFast Roofing Sheets to Steel Hex Screws have the following specification: Size: 5.5 x 50mmEffective Thread Length: 27mmPack Size: 100Drill Tip: No.5 No.5 drill tip for self-drilling in heavy gauge steel up to 12.5mm.
These Forgefix Multi-Purpose Pozi Screws with countersunk heads are made from A2 stainless steel. They are ideal for use in and with many materials. APPLICATIONIdeal for use in sanitary locations and in marine environments. Stainless Steel does not corrode, rust or stain with water as ordinary steel does, but despite the name it is not fully stain-proof, most notably under low oxygen, high salinity, or poor circulation environments. Stainless steel is used where both the properties of steel and resistance to corrosion are required. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. The screws' countersunk heads are designed to sink flush with substrates to leave a smooth surface finish. They have single threads, designed to offer higher pull out values and quicker insertion.Multi-Purpose Pozi Screw Countersunk ST Stainless Steel 4.0 x 40mm Box 200
