These Forgefix Cut Clasp Nails are specially designed for fitting floorboards. They are sometimes knowns as square nails, due to their rectangular shank shape.The nails have a 'Bright' finish, which is simply the basic raw mild steel material, without any coating or finish.Cut Clasp Nail Bright 65mm Bag Weight 500g
This Masterplug Metal Clad Light Switch has been designed to perform at 10AX inductive loads. Manufactured in heavy gauge steel and finished with a scratch resistant epoxy powder-coating. Flat profile with rounded edges, colour coded terminals with backed out captive screws for ease of installation. Suitable for everyday use in a garage, shed, commercial and industrial environments. 1 x Masterplug Metal Clad 2-Way 2-Gang Light Switch
White Gorilla Tape grips smooth, rough and uneven surfaces. It is a tough all-weather tape which is UV resistant. It has strong, reinforced backing and double thick adhesive.1 x Gorilla Glue Gorilla Tape White 48mm x 10m
Masterplug Connector Strips are manufactured from thermoplastic. Snap-off spine design. Fully backed out screws to speed installations. Manufactured to BS EN 60998 2-1.10 x Masterplug Connector Strips 5A 12W
These Forgefix TechFast Hex Head Roofing Screws are designed for fixing cladding and sheet steel to light section steel purlins of between 1.2mm and 3.6mm. The screws have a hex head, are self-drilling and have a rubber washer which expands under pressure to form a permanent weather seal. They are zinc plated and have an 'Elementech' coating for superior corrosion resistance, which has been salt spray tested to 1,000 hours.The TFHL5525 TechFast Hex Head Roofing Screws have the following specifications: Size: 5.5 x 25mm.Pack quantity: 100.
These ForgeFix ForgeFast Wood Screws have a universally accepted, Pozi compatible drive. They have 6 underhead lobes for improved countersinking and reduced surface dust, and reinforced countersunk necks which improve holding power. The screws have an anti-friction thread for reduced splitting of the timber, reduced 'jacking' and spinning of joined timber and improved drawing strength. The thread is serrated for improved pull-out and reduced torque when inserting the screw. The double cutting point allows faster drilling time and reduced clogging of wood dust and is capable of piercing 0.8mm steel. The screws have a 'Elementech 400' coating providing an anti-corrosive metal finish, which lasts up to 6 times longer than standard zinc coatings. The coating is environmentally friendly and does not contain Cr6+. It is Salt Spray tested to 400 hours. The screws are suitable for interior use.Size: 5.0 x 70mm.Box quantity: 100.
These Forgefix Carriage Bolts are Zinc Plated, and ideal for timber to timber joining. They come complete with a hex nut and are fully threaded to 100mm. Also known as 'Cup Square Hex Bolts', the square underneath the Cup stops rotation of the bolt when tightening. Conform to DIN 603 and DIN 934 standards. Available in a comprehensive range of sizes to suit most applications. APPLICATIONUsed mainly for fastening timber to timber and is extensively used for timber joist construction in house building and numerous decking applications. A Carriage Bolt, also known as a Coach Bolt or as a ‘Fully Threaded Cup Square Hex Bolt’, has a domed or countersunk head, and the shank is topped by a short square section under the head. The square section grips into the part being fixed (typically wood), preventing the bolt from turning when the nut is tightened. A rib neck Carriage Bolt has several longitudinal ribs instead of the square section, to grip into a metal part being fixed. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminium and stainless steels by their oxide layers.Carriage Bolt & Nut ZP M8 x 130 Bag 10
Plasplugs specialised, Hollow Door Fixings are ideal for fitting coat hooks, name plates and other fixings to the narrow gauge of hollow doors and panels. These tough, compact fixings have a rivet type action that grips the inside of the panel. Expanding wings grip securely in hollow doors, thin skin partitions, plywood and fibreglass. Multi-thread technology ensures superior holding power, ideal for the home, boat and caravan. Accepts No. 6 Screws.Drill size: 6mm.Supplied in a pack of 5.
Plasplugs® Solid Wall Super Grips™ are suitable for fixing into concrete and brick. They are available in 3 different sizes/colours. Yellow: Regular-duty, accepts screws No.4-8 (3-4.5mm)Red: Regular-duty, accepts screws No.6-12 (3.5-5.5mm)Brown: Heavy-duty, accepts screws No.8-14 (4.5-7mm)The brown wall plugs are heavy-duty and will accept screws No 8-14 (4.5-7mm). Drill: 7mm.Pack quantity: 100.
These Forgefix Multi-Purpose Pozi Screws with countersunk heads have a zinc yellow passivated finish for increased durability. The screws are immensely popular and versatile, and used in all trades including joinery, electrical and plumbing. Also widely used in DIY applications. APPLICATIONSuitable for use with many materials including PVCu, Timber, Chipboard, MDF, and other similar types. The Zinc Yellow Passivation process of electroplating is similar to the 'Galvanised' and 'Zinc Plated' processes but with the addition of a yellow dye. It offers an aesthetically pleasing finish, whilst having excellent resistance to corrosion. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. The countersunk head is designed to sink flush with substrates to leave a smooth surface finish. They have single threads, designed to offer higher pull out values and quicker insertion.Multi-Purpose Pozi Screw Countersunk ST ZYP 4.0 x 45mm Box 200
Gorilla Super Glue keeps holding strong, even when the bond takes a hit. Just hold in place for 30-60 seconds while the formula sets, no clamping necessary. Suitable for use on nearly anything: wood, metal, ceramics, some plastics, rubber and much more. Features include: IMPACT STRENGTH - unique rubber particles increase impact-resistance and strength to handle everyday use after your repair or creation is set. WON'T CLOG - anti-clog tip with metal pin keeps nozzle clean. EASY TO USE - thick formula flows better for improved control. Dries in just 30-60 seconds, with no clamping. WHATEVER THE SURFACE - use on nearly anything, from wood, metal, ceramics, some plastics, rubber and a whole lot more!Size: 15g.
Bostik all purpose adhesive is a fast drying clear strong adhesive that is ideal for household repairs, DIY tasks, craft and hobby and much more.Size 20ml Tube
A general purpose one-part contact adhesive suitable for bonding laminates, wallboards, plywood and hardboard panels, and leather goods. It has a high initial grab that bonds on contact, a high shear strength and good temperature resistance with an excellent final bond strength with low odour. BONDS: Decorative laminates, Rigid PVC, Wood, Chipboard, Hardboard, Cork, Leather, Rubber, Stone, Metal, Dense film fabrics, Ceramics, and Glass(Not suitable for use on polystyrene or cellulose painted surfaces).Size. 1 litre tin.
16 gauge finish nails, which are compatible with: Tacwise Air Powered Nailers: DFN50, DFN50WHH and FFN64LHH.Tacwise Battery Powered Nailers: Ranger 2 16G Nailer.And all other nailers that take 16g straight finish nails.
16 gauge finish nails, which are compatible with: Tacwise Air Powered Nailers: DFN50, DFN50WHH and FFN64LHH.Tacwise Battery Powered Nailers: Ranger 2 16G Nailer.And all other nailers that take 16g straight finish nails.
Rapid No. 53 precision cut fine wire staples are made from high performance galvanised steel for strength and durability. The fine wire makes the fixed staple almost invisible, ideal for fabrics, decoration, small construction and light repair.Type: 53 (galvanised)Size: 6mm leg length.Quantity: 2500. For use with: Rapid R53, R153, R253, R353, R453, MS2.1, MS4.1, ALU610, ALU753, ALU853, ALU953, E100, ESN530, BTX530, PS101, PS6-16, M10R, M20, M30, M40, Eco Tacker, Hobby Tacker, Hobby Tacker Dual, Multitacker, Compacta, Hobby Electric.
The ForgeFix Spectre Screws are advanced multipurpose wood screws with double countersunk heads and pozi compatible recess. They have a sawtooth thread design to prevent splitting and reamer to prevent jacking. The screws have a zinc yellow passivated finish for excellent resistance to corrosion. The zinc yellow passivation process of electroplating is similar to the 'galvanised' and 'zinc plated' processes but with the addition of a yellow dye. It offers an aesthetically pleasing finish.Specification: Size: 4.5 x 60mmThread: 36mm lengthPack Quantity: Box of 100
These Forgefix High Tensile Hex Head Bolts are made from 8.8 grade steel. The bolts are part threaded and conform to DIN 933 standards. The hexagonal head has been designed for use with spanners or sockets and offers maximum torque when used with these tools. APPLICATION:For fastening together numerous types of material or to be fastened into pre-tapped holes. Widely used in many engineering applications. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrityHigh Tensile Bolts ZP M6 x 60 Bag 10
16 gauge finish nails, which are compatible with: Tacwise Air Powered Nailers: DFN50, DFN50WHH and FFN64LHH.Tacwise Battery Powered Nailers: Ranger 2 16G Nailer.And all other nailers that take 16g straight finish nails.
These Forgefix Wing Nuts are a convenient alternative to the standard Hex Nut, and allow hand tightening rather than having to use spanners or other tools. The nuts are bright zinc plated for increased corrosion resistance. Also known as a 'Thumbscrew', the wing nut has two large metal 'wings' for easy tightening and loosening. APPLICATION:Where ever a hand tightened fastening is required. Used where frequent adjustments are needed or part removal can be made quickly at some later stage.Can be used with all threaded bolt products. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminum and stainless steels by their oxide layers.Wing Nut ZP M8 Bag 10
The Rapid waterproof rivets are ideal for use in humid areas. They are made from high grade aluminium and the head of the rivet is made of 1 single part to prevent leakage between the 2 parts when they are fixed together. The rivets are ideal for applications that require a waterproof fixing, such as on waterspouts, gutters, shower panels and greenhouses. Each pack is supplied with a drill bit.Specifications:Size: 4 x 12mm.Grip range: 6-9mm.Pack: Blister of 50.
