Unibond No More Nails is a high strength grab adhesive that eliminates the need for nails and screws in many DIY and repair jobs. It is safe and easy-to-use, adheres to most building materials and can be used to fill minor gaps on uneven surfaces. No More Nails is ideal for fixing skirting boards, dado rails, architraves, coving, polystyrene mouldings, decorative wall panels, plasterboard, carpet and carpet grippers and worktops.Unibond No More Nails Original Mini Tube 40ml Supplied in a handy mini tube.
The Gripit Mirror Kit includes everything you need to mount a mirror to a plasterboard wall. Contains: 2 x Gripit Red Fixings 18mm2 x Screws 5.0 x 30mm2 x Picture Hooks1 x Flat Drill Bit 18mm
Bondloc B454 is a Thixotropic Non-Drip Gel Cyanoacrylate that bonds metals, plastics, wood, ceramics, rubber, leather, card, glass and many other materials. Cyanoacrylate adhesives cure through reaction with moisture held on the surface to be bonded. They need close fitting joints and usually solidify in seconds which has resulted in the universal generic name of 'Superglues'. Curing is started by the film of moisture found on most surfaces which is usually slightly alkaline and it is this alkalinity which causes the polymerisation. Most grades have varying viscosities and therefore they need close fitting joints. Newer developments of gelled variants allow cure in wider gaps and application to vertical surfaces. Cyanoacrylates are suited to small plastic parts and to rubber bonding. Liquid Properties:Ester base: Ethyl cyanoacrylateAppearance: Clear, colourlessSpecific Gravity: 25°C 1.1 g/cm²Shelf life: 12 months unopenedViscosity @ 25°C: GelSize: 20g
Bondloc B2001 is a hand kneadable, specialty epoxy putty that mixes in 1 minute for permanent repairs to many substrates. Contains fading black dye that becomes grey after mixing. May be applied under water (fresh or salt). Bonds to fibreglass, metal, wood, concrete and glass. Will not yellow to UV exposure. Hardens in 10 minutes, back in service in an hour, full strength in 24 hours. Can be used for repairing tanks and drums, patching holes in pipes, stopping leaks and repairing porosity holes in castings. Specification: Typical Properties: 7 days cured at 24°CColour: Black, changes to grey after mixingViscosity: putty/hand kneadablePot Life @24°C: 20 minutesComprehensive Strength: 83 N/mm2Adhesive Tensile Shear: 5 N/mm2Cured Hardness Shore: D 75Dielectric Strength: volts/mil 300Solids: 100%Temperature Resistance: Wet: 49°C, Dry: 121°CSize: 50g
These Forgefix Plasterboard Spring toggles have an all-metal constuction, making them ideal for applications where heat resistance is required. Their wide span wings spread load, ensuring an increased holding capacity. They have excellent holding in lathe and plaster applications.The toggles are quick and easy to use, with no requirement for specialist tools. APPLICATION:Light to medium-duty fixing for all manner of fixtures including bathroom accessories, shelving, lighting, radiators and much, much more.Plasterboard Spring Toggle M3 x 50 Bag 10
These Forgefix Hexagon Nuts are bright Zinc Plated for increased corrosion resistance. The hexagonal shape is designed to be driven by a wrench (spanner) and provides excellent torque when done so. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrates surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminum and stainless steels by their oxide layers.Hexagon Nut ZP M4 Bag 100
These Forgefix General Purpose Pozidrive Screws with Countersunk heads are zinc plated for increased durability. They are an extremely popular general purpose screw, and suitable for use in and with many materials. APPLICATION:Ideal for use in many ironmongery, electrical and plumbing applications.Can be used with various screw cover caps. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminium and stainless steels by their oxide layers. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. The countersunk head is designed to sink flush with substrates to leave a smooth surface finish. They have twin threads, which enable an easy start when driving. Imperial Size > MetricNo.4 = 3.0mm, No.6 = 3.5mm, No.7 = 3.9mmNo.8= 4.0mm, No.10 = 5.0mm, No.12 = 6.0mmGeneral Purpose Pozi Screw Countersunk TT ZP 3 x 12 Box 100
The Arrow T59 Insulated Staples are for use with the Arrow T59. Ideal for tacking bell wire, etc.Arrow T59 Insulated Staples have the following specification: Size: 6 x 6mm.Colour: Clear.Quantity: Box 300.
These Forgefix Masonry Anchor Projection Bolts have a Zinc Yellow Passivated finish for increased durability and resistance to corrosion. They have a tough and reliable construction to cover most heavy-duty fixing applications. The four-way expansion shield offers extremely strong and secure anchorage, and the specially manufactured retaining spring ensures encapsulation of the wedge during expansion. Projection bolts offer easier fixture removal or repositioning due to the bolt remaining in the shield. APPLICATION:Ideal for securing reinforcement wall plates, lighting supports, guy ropes and bracketry.Ensure the correct socket drive or spanner is used to ensure accurate installation. When sizing a Masonry Anchors it is most important to know the depth of the material that you are fixing.Eg: Size M610: The 'M6' is the thread size of the bolt. The '10' denotes the maximum thickness of material it will fix. The Zinc Yellow Passivation process of electroplating is similar to the ‘Galvanised’ and ‘Zinc Plated’ processes but with the addition of a yellow dye. It provides a coating that is aesthetically pleasing, and which offers excellent resistance to corrosion.Masonry Anchor Bolt Projecting Zinc Yellow Passivated M12 x 30 Bag 5
These Forgefix General Purpose Pozi Screws with countersunk heads have an electro brassed finish for increased durability and to suit most internal and decorative requirements. They are versatile screws, ideal for use in and with many materials. APPLICATION:Ideal for use in many decorative installations.Can be used with various screw cover caps. The Electro brassed process of electroplating is similar to the 'Galvanised' and 'Zinc Plated' processes but with the addition of a dye. It offers an aesthetically pleasing finish that is resistant to corrosion. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. The screws' countersunk heads are designed to sink flush with substrates to leave a smooth surface finish. They have twin threads to enable an easy start when driving.General Purpose Pozi Screw Countersunk TT Electro Brass 1/2 x 4 Box 200
ForgeFix ForgeFast Wood Screws have a universally accepted, Torx® compatible drive. Their recessed ribs provide improved countersinking and reduced surface dust, and their reinforced countersunk necks improve holding power. The screws have a patented drill and drive thread for reduced splitting of the timber, reduced 'jacking' and spinning of joined timber, increased pull-out and a firmer fix. A sharp point provides faster bite and is capable of piercing 0.8mm steel. The screws have an 'Elementech 400' coating providing an anti-corrosive metal finish, which lasts up to 6 times longer than standard zinc coatings. The coating is environmentally friendly and does not contain Cr6+. It is Salt Spray tested to 400 hours. The screws are suitable for interior use. Every box is supplied with a Torx® compatible bit.Size: 4.0 x 70mm.Box quantity: 100.
The Rapid R13E and R53E Staple Guns are ideal for hobby and DIY applications. Suitable for home decor, securing textiles, reupholstery and light-duty repair. They fire fine wire staples that are barely visible and have minimal effect on the textile fibres. An easy colour match staple system ensures you have the right size staple. Made in tough, robust plastic with all steel wear parts inside. The staple guns are recoilless for comfort during long term use and also have a noise damper and an integrated locking function for storage. The ergonomic design with low-angle handle ensures a comfortable fit in the hand and are easy-to-use. R53E Fires: Type 53 Fine Wire Staples: 4-10mm.R13E Fires: Type 13 Fine Wire Staples: 4-10mm. Covered by a 2 year guarantee. Made in Sweden.The Rapid R53E fires Type 53 fine wire staples 4-10mm.
Powerful, no compromise staple guns for 6-8mm staples. Designed for demanding professional applications and precision operations (tested to 100,000 fixings). All steel casing and wear parts inside. It's easy to load, has no recoil, and fits comfortably into the hand. Made in Sweden. 5 Year Guarantee.Staples: No.53 Fine Wire Staples 6-8mm.
Rapid No. 140 precision cut flat wire staples are made from high-performance galvanised steel for strength and durability. Flat wire staples have a larger holding area against the material, making them ideal for thin plastic or insulation.Type: 140 (galvanised)Size: 14mm leg length.Quantity: 2,000. For use with: Rapid R34, R44, R64, ALU740, ALU840, ALU940, R54, E-tac, ESN114, R214, PS111 tackers.
PINKGRIP DRY FIX is a revolutionary new type of fast curing, adhesive foam that has been specially developed for the rapid installation of Plasterboard, Insulation Boards and other sheet materials such as Roof Decking and Floorboards. PINKGRIP DRY FIX provides significant labour saving and convenience benefits when compared to traditional dry wall adhesives. It will bond to most common building substrates; can be applied horizontally or vertically to boards, walls or battens/beams. The foam expands very minimally on application but enough to fill any gaps on uneven surfaces. PINKGRIP DRY FIX can be applied using an Everbuild Dry Fix Applicator Gun.
These Forgefix TechFast Hex Head Roofing Screws are designed for fixing cladding and sheet steel to heavy section steel purlins of between 6.0mm and 12.5mm. The screws have a hex head, are self-drilling and have a rubber washer which expands under pressure to form a permanent weather seal. They are zinc plated and have an 'Elementech' coating for superior corrosion resistance, which has been salt spray tested to 1,000 hours.The TFHH5535 TechFast Hex Head Roofing Screws have the following specifications: Size: 5.5 x 35mm.Pack quantity: 100.
The BlueSpot S Hook Cam Buckle is manufactured from polyester webbing with stitched reinforcement for increased durability. Fitted with plastic coated, steel S hooks for increased corrosion protection. The automatic locking cam has a quick-release function for quick and easy use and the polyester webbing is resistant to cutting and friction abrasion. The cam buckle is ideal for the securing of large, bulky or awkwardly shaped loads during transportation. Specification: Working Capacity: 250kgBreaking Capacity: 500kgLength: 2mWidth: 25mm
These Forgefix Hinged Cover Caps, sometimes known as 'Fold Over Cover Caps', are extremely versatile and will suit most type of screw heads. APPLICATION:Offer a concealed yet aesthetically pleasing finish where screws would normally be bare to the elements or the eye.Used for many sign and sanitary installations as well as cupboard and carcass assembly.Hinged Cover Cap Grey No.6-8 Bag 100
ForgeFix ForgeFast Wood Screws have a universally accepted, Torx® compatible drive. Their recessed ribs provide improved countersinking and reduced surface dust, and their reinforced countersunk necks improve holding power. The screws have a patented drill and drive thread for reduced splitting of the timber, reduced 'jacking' and spinning of joined timber, increased pull-out and a firmer fix. A sharp point provides faster bite and is capable of piercing 0.8mm steel. The screws have an 'Elementech 400' coating providing an anti-corrosive metal finish, which lasts up to 6 times longer than standard zinc coatings. The coating is environmentally friendly and does not contain Cr6+. It is Salt Spray tested to 400 hours. The screws are suitable for interior use. Every tub is supplied with a Torx® compatible bit.Size: 5.0 x 70mm.Pack quantity: 450.
These Forgefix Multi-Purpose Pozi Screws with countersunk heads have a zinc yellow passivated finish for increased durability. The screws are immensely popular and versatile, and used in all trades including joinery, electrical and plumbing. Also widely used in DIY applications. APPLICATIONSuitable for use with many materials including PVCu, Timber, Chipboard, MDF, and other similar types. The Zinc Yellow Passivation process of electroplating is similar to the 'Galvanised' and 'Zinc Plated' processes but with the addition of a yellow dye. It offers an aesthetically pleasing finish, whilst having excellent resistance to corrosion. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. The countersunk head is designed to sink flush with substrates to leave a smooth surface finish. They have single threads, designed to offer higher pull out values and quicker insertion.Multi-Purpose Pozi Screw Countersunk ST ZYP 3.0 x 10mm Box 200
